User manual

14
VST Connections: Setting up input and output busses
About this chapter
Cubase uses a system of input and output busses to trans-
fer audio between the program and the audio hardware.
• Input busses let you route audio from the inputs on your audio
hardware into the program. This means that when you record
audio, you will always do this through one or several input
busses.
• Output busses let you route audio from the program to the
outputs on your audio hardware. When you play back audio,
you will always do this through one or several output busses.
As you can see, the input and output busses are vital when
you work with Cubase. This is why you find this chapter in
the beginning of the Operation Manual – once you under-
stand the bus system and set up the busses properly, it will
be easy to go on with recording, playing back, mixing and
doing surround work (Cubase only).
Setting up busses
Strategies
In Cubase, you can create any number of busses. A num-
ber of surround formats are supported (Cubase only). In
Cubase Studio, busses are in mono or stereo.
Ö The bus configuration is saved with the projects –
therefore it’s a good idea to add and set up the busses
you need and save these in a template project (see “Save
as Template” on page 451).
When you start working on new projects, you start from this template.
That way you get your standard bus configuration without having to make
new bus settings for each new project. If you need to work with different
bus configurations in different projects, you can either create several dif-
ferent templates or store your configurations as presets (see “Other bus
operations” on page 17). The templates can of course also contain other
settings that you regularly use – sample rate, record format, a basic track
layout, etc.
So, which type of busses do you need? This depends on
your audio hardware, your general audio setup (e.g. sur-
round speaker setup) and what kind of projects you work
with.
Here’s an example:
Let’s say you are using audio hardware with eight analog
inputs and outputs and digital stereo connections (10 in-
puts and outputs all in all). Furthermore, you work with a
surround setup in 5.1 format (Cubase only). Here’s a list
of busses you may wish to add:
Input busses
• Most likely you need at least one stereo input bus assigned to
an analog input pair. This would let you record stereo material.
If you want to be able to record in stereo from other analog in-
put pairs as well, you could add stereo input busses for these
too.
• Although you can record mono tracks from one side of a ste-
reo input, it may be a good idea to add a dedicated mono in-
put bus. This could be assigned to an analog input to which
you have connected a dedicated microphone pre-amp for ex-
ample. Again, you can have several different mono busses.
• You probably want a dedicated stereo input bus assigned to
the digital stereo input, for digital transfers.
• If you want to transfer surround material directly to a surround
track, e.g. from surround-configured location recording equip-
ment, you need an input bus in that surround format (Cubase
only) – in this example, this would be a 5.1 input bus.
Output busses
• You probably want one or several stereo output busses for
monitoring and listening to stereo mixes .
• For digital transfers, you need a stereo bus assigned to the
digital stereo output as well.
• You need a surround bus in the format of your speaker config-
uration (in this example, 5.1) assigned to the correct outputs
(which in turn are connected to the correct speakers). Again,
this is available in Cubase only.
• You may want additional surround busses if you tend to work
in different surround formats.
!
Different busses can use the same inputs/outputs on
the audio hardware! For example, you may want a
stereo output bus assigned to the same outputs as
the front stereo channels in your surround bus – this
makes it easy to listen to stereo mixes without having
to reconnect your speakers.