Plug-in Reference

72
The included VST Instruments
Envelope
LFO
X/Y Pad
Effects
Master
Parameter Description
A – (Attack) Sets the attack time.
D – (Decay) Sets the decay time.
S – (Sustain) Sets the sustain level.
R – (Release) Sets the release time.
Mod Src (A+B) Defines the envelope modulation source. You can select:
Modwheel, Aftertouch, Pitchbend, Velocity, LFO and
Mod Env.
Depth (A+B) Controls the envelope modulation depth for the mod
source defined in the “mod src” field.
Parameter Description
Waveform
(pop-up menu)
Here, you can select the waveform for the low frequency
oscillator. Available waveforms are: Triangle, Square,
Sawtooth, Sample & Hold and Random.
Rate Adjusts the frequency of the LFO, thus changing the rate
of the modulation. Depending on the LFO sync parame-
ter, you can edit the rate in Hertz or in note values.
Sync When “Sync” is “on” the LFO speed will be synchronized
to the sequencer’s tempo. This also affects the LFO rate
format.
Mod Src Defines the LFO modulation source. Available sources
are:
Modwheel, Aftertouch, Pitchbend, Velocity, LFO and
Mod Env.
Depth Controls the LFO modulation depth for the mod source
defined in the “mod src” field.
Parameter Description
X Par Sets the parameter to be modulated on the x axis of the
XY Pad. All of Monologue’s parameters are available as
destinations.
Y Par Sets the parameter to be modulated on the y axis of the
XY Pad.
XY Pad Use the mouse to control any two of Monologue’s param-
eters in combination. By moving the mouse horizontally,
you can control the x parameter, by moving it vertically,
you can control the y parameter. You can also record
controller movements as automation data.
Parameter Description
FX Type
(pop-up menu)
Selects the effect type for Monologue’s pitch effects. The
available types are Chorus, Flanger and Phaser.
Rate Use this to adjust the rate of the effect modulation.
Depth Use this to adjust the depth of the effect modulation.
FBK Controls the feedback of the effect.
Mix Controls the balance between dry and wet (effect) signal.
Set to 0, the effect will be off. Set to 50, the balance be-
tween dry and wet signal is 50/50.
Overdrive Controls the amount of overdrive (distortion) added to
the signal. A slight amount of overdrive will create punch
and bottom. Higher amounts will add distortion.
Delay Sets the delay time in musical values. The delay effect is
always in sync with the song tempo.
Spread Controls the stereo spread of the delay signal. If you set
this to 0, the delay will be centered mono. Higher
amounts of spread will shift the left and right delay chan-
nels. If you set this to 100, the delays will “ping-pong”
between the left and right channels at an even rate.
Tone Adds a low pass filter to the delay. Increasing “tone” will
make every delay repetition darker in tone.
FBK Controls the amount of feedback of the delay. High feed-
back levels will create infinite delays. Use this parameter
with caution.
Mix Controls the balance between dry and wet (effect) signal.
Set to 0, the effect will be off. Set to 50, the balance be-
tween dry and wet signal is 50/50.
Parameter Description
Glide Mode The available modes are: “held”, “on” and “off”. With
“held” selected, a glide effect only occurs for notes
played legato.
Rate Controls the glide rate – the time it takes for a note to
reach its destination pitch.
PB Range Controls the range of a pitch bend MIDI controller. Range
can be set between 1 and 24 semitones for a total of two
octaves.
Env Trigger When set to “Multi”, each keystroke will re-trigger the en-
velopes. When set to “single”, legato notes will not retrig-
ger the envelopes, effectively holding the envelopes on
the sustain level until all keys are released before a new
note is triggered.
Note Priority Defines which note is played when multiple keys are held.
Options are: First, Lowest, Highest, and Last.
Oct Controls the master pitch of Monologue in octave steps.
Range is +/- 4 octaves.
Master Out Controls the master output level that is sent to the VST
mixer. Use it to adjust the balance between different pre-
sets. Use the VST mixer channel volume to control or au-
tomate the Monologue master volume.
Keyboard Pressing the “keyboard” button will reveal a six octave
virtual keyboard. Pressing the “keyboard” button again
will hide the keyboard and display the master section
again.
Parameter Description