Use and Care Manual

ManualsBrandsSTEELEX ManualsJointers6 in. Jointer with Mobile Base

ST1010 6" Jointer (Mfd. Since 3/16)

-13-

The following is a list of items shipped with your

machine. Before beginning setup, lay these items out

and inventory them.

Note: If you cannot find an item on this list, carefully

check around/inside the machine and packaging mate-

rials. Often, these items get lost in packaging materials

while unpacking or they are pre-installed at the factory.

Box 1 (Figure 5) Qty

A. Table Assembly ............................................................ 1

B. Fence Carriage Assembly ......................................... 1

C. Carriage Mounting Bracket ..................................... 1

D. Infeed Table Lever ....................................................... 1

E. Fence Tilt Handles ....................................................... 2

F. Cutterhead Guard ....................................................... 1

G. Push Blocks ................................................................... 2

H. Outfeed Table Handwheel ....................................... 1

I. Knife-Setting Jig .......................................................... 1

J. Fence Assembly ........................................................... 1

Inventory

Figure 5. Box 1 contents.

Figure 6. Box 2 contents.

Hardware (See Hardware Recognition Chart)

• Hex Bolts M10-1.5 x 55 (Foot Pedal) .................... 2

• Hex Nuts M10-1.5 (Foot Pedal) .............................. 2

• Hex Bolt M8-1.25 x 50 (Foot Pedal) ...................... 1

• Flat Washers 8mm (Foot Pedal, CarriageBracket,

Fence Carriage, Fence, Switch) ...........................11

• Flat Washers 10mm (Foot Pedal, Jointer/

Cabinet) .......................................................................... 5

• Cap Screws M10-1.5 x 20 (Jointer/Cabinet) ...... 3

• Lock Washers 10mm (Jointer/Cabinet) ............... 3

• Cap Screws M8-1.25 x 60 (Carriage Bracket) .... 4

• Lock Washers 8mm (Carriage Bracket, Fence

Carriage, Fence, Switch) .........................................10

• Cap Screws M8-1.25 x 20 (Fence Carriage)........ 2

• Cap Screws M8-1.25 x 25 (Fence).......................... 2

• Set Screw M5-.8 x 12 (Cutterhead Guard) ......... 1

• Phillip Head Screws M5-.8 x 16 (Dust Port) ....... 4

• Flat Washers 5mm (Dust Port) ................................ 4

• Cap Screws M8-1.25x 40 (Switch) ......................... 2

• Hex Nuts M8-1.25 (Switch) ...................................... 2

• Phillips Screws M5-.8 x 12 (Switch)

• Hold Downs (Switch) ................................................. 2

• Phillips Screw M6-1 x 12 (Handwheel) ................ 1

• Flat Washer 6mm (Handwheel) ............................. 1

Box 2: (Figure 6) Qty

K. Cabinet ........................................................................... 1

L. Power Switch and Support Arm ............................ 1

M. V-Belt ............................................................................... 1

N. Locking Foot Pedal Assembly ................................ 1

O. Leveling Feet ................................................................ 2

P. Dust Port ........................................................................ 1

Tools (Not Shown) Qty

• Wrenches 8/10mm, 12/14mm .........................1 Ea.

• Hex Wrenches 2.5, 3, 4, 6, 8mm .......................1 Ea.

When ordering replacement parts, refer to

the parts list and diagram in the back of the

manual.

Some hardware/fasteners on the inventory list

may arrive pre-installed on the machine. Check

these locations before assuming that any items

from the inventory list are missing.