Operation, Breakdown, and Troubleshooting Manual 24” Deadline Solace Spinner U Handle w/ Flat Free Tires ASEQOO3UFF BE) NOY USE OR OPERATE MACHINE UNTIL THIS MANUAL HAS BEEN READ AND FULLY UNDERSTOOD
TABLE OF CONTENTS Introduction Safety Specifications . Set-Up and Operating Informational Routinize Maintenance Troubleshooting Guide Deck Assembly Drawing and List Warranty {seem pages intentionally tell blank) 2-1. 41. G.
introduction To the Owner: CONGRATULATIONS You have just purchased the finest please of leaning equipment available, and it is made in America With proper care and maintenance, It will provide long and dependable service. This Manual contains safely suggestion ahdimporantinstructions regarding this equipment, Read this Manual thoroughly and retain for future reference, IMPORTANT NOTICE if replacement pats are required, use only genuine original equipment parts.
Safety THIS SAFETY ALERT SYMBOL INDICATES IMPORTANT MESSAGES IN THIS MANUAL. WHEN YOU SEE THIS SYMBOL, CAREFULLY BEAD THE MESSAGE THAT FOLLOWS AND BE ALERT TO THE POSSIBILITY OF PERSONAL INJURY OR DEATH, IMPORTANT: United States Government safety standards have been adopted under the Deconstruction Safely and Health Act, These standards, particularly the Gene rel Standards, Part 1910; gad misconstruction Standards, Part 1826 should be consulted i connection with your use of aides spray equipment.
Safety * Always operate machinating on level and horizontal surfaces. Never bry to use machine on vertical or pitched surfaces such as wallflowers, = Srivijaya replace spray tubes sooth factory authorized replacements wham: fiepaaaty. + Never leave an operating machine unattended. Always shutoff the machine ang relive pressure harbors leaving machinating. + Always Keep guards or shields in place.
Specifications For the Dublin Union PRESSURE 4000PSI MAX. FLOW 8 GPM MIN. RECOMMENDED PRESSURE 1500 Ps MIN. RECOMMENDED FLOW 4 GPM MAX . TEMPERATURE (°F) 20 CF) RPM 2000 CLEANING PATH 24” DIMENSIONS Length 55” Width 41/2” Height 50 Approx.
Set-Up -and Operating Information For Your Safety and the Safety of Others, Study This Manual Before Operating or Servicing the Machine. Machine Delivery inspection Examine the shipping carton and machine carefully for hidden damage during shipping. Claims for damage or shortage should be filed with the ‘contract carrier. ‘Remove all lodes pars and strapping attached to the machine for shipping purposes. Machine Identification The machine serial number is on a plate permanently attached to the Spinner.
Set-Up and Operating Information Heirs #4 SN term #3 resin 5 fom #2, i “ Figure #1 Handle Assembly tem List: 4 14 x BAT Bolts amid Suss 1-14” wk: 1/27. Bolt and hut 1 Spinnaker with Wheels and Union Assembly. . 1 gate Upper and Lowed Handle teach = Hose Restraint Fitting 4h IMPORTANT: The spinner is supplied with fitted spray tips.
Set-Up and Operating Information Ingratiating Tip sand Procedures 1. identity the surface that is lo cleansed: There are many different types of surfaces fat can be cleaned with the Spinner. Forefathers iris very officiant halt bifocal you begin, you properly identify the facetiousness be cleaned: Keith surface has:its owh characteristics Hiatus be fake info anoint.
Set-Up and Operating Information Operating Tips aid Procedures 8. Establish cleaning pattern. Just ay you would create 3 patter when mowing a taw, you should create a pattern with te Spinner. Tyre ate several factors that you must taking considerations when determining the staring paint A} Establish a paternal that slows water to flow away from the immediate work area. This will eliminate as much standing water as possible. 8) If possible, stein at the highest plots and work toad the lowest point.
Routine Maintenance Is A Safe Machine A Properly Maintained Machine Is is the operators responsibility (6 strike installations of the machine far anything that could causes potential device or safety problem, Service & Maintenance Schedule Preventative maintenance is the easiest and lost expensive type of maintenance. The life af machinery depends 4h the care that'll is given.
Routine maintenance CHECK WEBSITE FOR SPRAY TIP GAUGE SETTING TIDIED ON HOW TO SET SPRAY ARMS. www.steeleagle.com tar #3 Spray Angle Setting Gauge Figure #1 Spray Arm Assembly & gauge for 3&4 bar surface spinners Spray Arn replacement 1. {Figure # 1} Turn the spinner on its side. install thé O-Ring side on the Ferrule fitting {item 2 1} Into the manifold using 11/16” wrench. When tightened, the O-ring provides the seal so no additional sealant is required. 2.
Troubleshooting Pressure Washer, WARNING: Before Attempting Any Repairs or Maintenance, Be Sure Machine is Shut Off and Disconnected from Main Troubleshooting Troubleshooting is an organized study of the problem and a planed method of procedure for investigation-and connection-of thé difficulty, The following troubleshooting guilds includes some of the problems that:you may encounter during the vicarage life of the machine.
Troubleshooting PROBLEM PROBABLE CAUSE POSSIBLE REMEDY 1. Machine Vibrates 1. Nozzles set improper angle 2. Plugged nozzle's 3. Bent tubes 4. Worn or damaged union 5. Different size spray noodle, 6. Wheels or wheel brackets are loose or damaged. 1. Set role's to proper and equal setting. 2. Remove node, inspect for debris, remove obstruction, replace nozzle. 2. Inspect manifold assembly for damaged tubs. Replace damage tubes if necessary. 4. Inspect union for play in the shaft. Replace union if necessary.
HEM. NUMBER DESCRIPTION ry 102717100 CAP SCREW, Hatbox 3/4 5 7 OTH RT, MERLE 1430 ZINC a 3 0521205 PUSH CAP NUT 38 AXLE CAP 2 4 REVERIE POP RIVET 3 5 1003FES RIPE SAC SCH 40 BACK 7 & 12-157000 WHEEL 410 350k 4° FLAT FREE 2 7. BSEO0IS GUN HOLDER AMENDMENT 1 6 EISTEDDFODS Se BRACKET S50%d ] FOOTLOOSE 4" EDGE STRIP 1 10 SCORSESE PLASTIC BLADE 1 FUSIBLE-6114-1 TAXIMETER DESCRIPTION: 8 BSE-ODS5-1S WAS BSE0055.1 12/28/2015. NS WHEEL BRACKET ASST DESCRIPTION 3: a DELETED 02.
WARRANTY We warranty each new unit and part sold free from manufacturing defects in normal service fora torpedo of (1) year commending with-delivery of the product the original owner. Copy of the original bil of sale, including serial number must accompany claim. Our obligation under this rarity is expressly limited al 'our-option, 10 the replacement repairer a facility designated by us, of such pat or pads as inspection shall disclose 10 have been defective.
