User manual
Table Of Contents
- 1 General information
- 2 Quick guide
- 3 Overview
- 4 Installation of the base system
- 5 Initial commissioning of the base system
- 6 Installation and initial commissioning of optional components
- 6.1 Commissioning the SD card (MPPT 6000-M only)
- 6.2 AUX 1,2,3 relay output connection (MPPT 6000-M only)
- 6.3 AUX IO remote control input connection (MPPT 6000-M only)
- 6.4 PA TS-S external temperature sensor connection
- 6.5 StecaLink slave connection
- 6.6 StecaLink master connection (MPPT 6000-M only)
- 6.7 UART/RS-232 interface connection (MPPT 6000-M only)
- 6.8 Redundancy function (MPPT 6000-S only)
- 6.9 Install cable strain relief
- 7 Display (layout, function, operation)
- 8 System functions
- 8.1 Protection functions
- 8.2 Battery type setting
- 8.3 Current limit system setting (MPPT 6000-M only)
- 8.4 Current limit device setting
- 8.5 Lead-acid battery system functions
- 8.5.1 Equalisation cycle mode
- 8.5.2 Battery control mode (MPPT 6000-M only)
- 8.5.3 Battery capacity test (MPPT 6000-M only)
- 8.5.4 Battery type
- 8.5.5 Battery capacity
- 8.5.6 Current limit system (MPPT 6000-M only)
- 8.5.7 Current limit device
- 8.5.8 Charge voltages
- 8.5.9 IUIA charge mode (MPPT 6000-M only)
- 8.5.10 Start boost charge
- 8.5.11 Battery temperature sensor
- 8.5.12 Cable compensation
- 8.5.13 PV string connection
- 8.5.14 Expert menu
- 8.6 Li-Ion battery system functions (MPPT 6000-M only)
- 8.7 NiCd battery system functions (MPPT 6000-M only)
- 8.8 StecaLink bus
- 8.9 Internal data logger
- 8.10 Clear log data
- 8.11 Clear event log
- 8.12 Factory settings
- 8.13 UART/RS-232 interface (MPPT 6000-M only)
- 8.14 Acoustic alarm
- 8.15 SD card (MPPT 6000-M only)
- 9 Control functions via AUX 1/2/3 (MPPT 6000-M only)
- 10 Troubleshooting
- 11 Maintenance, dismounting and disposal
- 12 Technical data
- 13 Guarantee conditions, exclusion of liability, contacts, notes
Battery capacity test
✔
‘Main menu è Battery settings è Battery capacity test ’
1. Press SET. The Start capacity test dialogue appears (Fig.
left).
2. Press and hold SET for 1 s. The capacity test starts.
3. The display switches to the Battery settings menu.
If the capacity test could be successfully started then charging
is deactivated (OFF) and the code C
is displayed in the footer of
the status screen, see
Ä
Chapter 7.3 ‘Status display’
on page 53.
8.5.4 Battery type
For information on switching between the lead-acid, lead-gel/AGM, Li-Ion and NiCd battery
types, see
Ä
Chapter 5 ‘Initial commissioning of the base system’ on page 33.
8.5.5 Battery capacity
For the battery capacity settings see
Ä
Chapter 5 ‘Initial commissioning of the base system’
on page 33.
8.5.6 Current limit system (MPPT 6000-M only)
For the current limit system setting, see
Ä
Chapter 8.3 ‘Current limit system setting (MPPT
6000-M only)’ on page 60.
8.5.7 Current limit device
For the current limit device setting, see
Ä
Chapter 8.4 ‘Current limit device setting’
on page 61.
8.5.8 Charge voltages
CAUTION!
Ensure that the charge limit settings agree with the specifications of your battery. Incorrect
settings can destroy the battery.
756.404 | Z01 | 16.06
66