User manual
Table Of Contents
- 1 General information
- 2 Quick guide
- 3 Overview
- 4 Installation of the base system
- 5 Initial commissioning of the base system
- 6 Installation and initial commissioning of optional components
- 6.1 Commissioning the SD card (MPPT 6000-M only)
- 6.2 AUX 1,2,3 relay output connection (MPPT 6000-M only)
- 6.3 AUX IO remote control input connection (MPPT 6000-M only)
- 6.4 PA TS-S external temperature sensor connection
- 6.5 StecaLink slave connection
- 6.6 StecaLink master connection (MPPT 6000-M only)
- 6.7 UART/RS-232 interface connection (MPPT 6000-M only)
- 6.8 Redundancy function (MPPT 6000-S only)
- 6.9 Install cable strain relief
- 7 Display (layout, function, operation)
- 8 System functions
- 8.1 Protection functions
- 8.2 Battery type setting
- 8.3 Current limit system setting (MPPT 6000-M only)
- 8.4 Current limit device setting
- 8.5 Lead-acid battery system functions
- 8.5.1 Equalisation cycle mode
- 8.5.2 Battery control mode (MPPT 6000-M only)
- 8.5.3 Battery capacity test (MPPT 6000-M only)
- 8.5.4 Battery type
- 8.5.5 Battery capacity
- 8.5.6 Current limit system (MPPT 6000-M only)
- 8.5.7 Current limit device
- 8.5.8 Charge voltages
- 8.5.9 IUIA charge mode (MPPT 6000-M only)
- 8.5.10 Start boost charge
- 8.5.11 Battery temperature sensor
- 8.5.12 Cable compensation
- 8.5.13 PV string connection
- 8.5.14 Expert menu
- 8.6 Li-Ion battery system functions (MPPT 6000-M only)
- 8.7 NiCd battery system functions (MPPT 6000-M only)
- 8.8 StecaLink bus
- 8.9 Internal data logger
- 8.10 Clear log data
- 8.11 Clear event log
- 8.12 Factory settings
- 8.13 UART/RS-232 interface (MPPT 6000-M only)
- 8.14 Acoustic alarm
- 8.15 SD card (MPPT 6000-M only)
- 9 Control functions via AUX 1/2/3 (MPPT 6000-M only)
- 10 Troubleshooting
- 11 Maintenance, dismounting and disposal
- 12 Technical data
- 13 Guarantee conditions, exclusion of liability, contacts, notes
Additional symbols used in the MPPT 6000-M
I (IUIA charge)
C (Capacity test running)
L (Li-Ion charge mode)
A (NiCd charge mode)
Additional symbols used in the MPPT 6000-S
S (StecaLink slave mode active)
⑤
Time
⑥
Derating symbol. Active when the device automatically reduces
the output power due to overloading.
7.4 Display of special states
n When the inverter is processing large amounts of data it is not able to process any user input.
This is indicated by an animated sun symbol:
n The backlight blinks red when faults occur. An event message is also displayed. More
information on this is provided in
Ä
Chapter 10.2 ‘Event messages’ on page 111.
7.5 General operation
Paging through displays and menu levels
1. If necessary, press ESC for 1 s to show the basic setting of the
status display.
2.
Press D, Ñ to display the measurements.
3. Press SET. The main menu appears and the top entry is
selected.
4.
Press D, Ñ to select a different entry.
5. Press SET. The submenu appears.
6. Repeat steps 4 and 5 if necessary.
7. Press ESC briefly to jump one menu level higher or press ESC
for a longer time (1 s) to show the basic settings of the status
display.
7.6 Advanced operation
Switching the device on/off
✔
‘Main menu è Device On/Off
’
1.
Press D, Ñ to select On or Off.
2. Press SET. Charging of the battery is switched on/off. OFF is
displayed in the basic setting of the status display when
charging is switched off.
756.404 | Z01 | 16.06
56