User manual
Table Of Contents
- 1 General information
- 2 Quick guide
- 3 Overview
- 4 Installation of the base system
- 5 Initial commissioning of the base system
- 6 Installation and initial commissioning of optional components
- 6.1 Commissioning the SD card (MPPT 6000-M only)
- 6.2 AUX 1,2,3 relay output connection (MPPT 6000-M only)
- 6.3 AUX IO remote control input connection (MPPT 6000-M only)
- 6.4 PA TS-S external temperature sensor connection
- 6.5 StecaLink slave connection
- 6.6 StecaLink master connection (MPPT 6000-M only)
- 6.7 UART/RS-232 interface connection (MPPT 6000-M only)
- 6.8 Redundancy function (MPPT 6000-S only)
- 6.9 Install cable strain relief
- 7 Display (layout, function, operation)
- 8 System functions
- 8.1 Protection functions
- 8.2 Battery type setting
- 8.3 Current limit system setting (MPPT 6000-M only)
- 8.4 Current limit device setting
- 8.5 Lead-acid battery system functions
- 8.5.1 Equalisation cycle mode
- 8.5.2 Battery control mode (MPPT 6000-M only)
- 8.5.3 Battery capacity test (MPPT 6000-M only)
- 8.5.4 Battery type
- 8.5.5 Battery capacity
- 8.5.6 Current limit system (MPPT 6000-M only)
- 8.5.7 Current limit device
- 8.5.8 Charge voltages
- 8.5.9 IUIA charge mode (MPPT 6000-M only)
- 8.5.10 Start boost charge
- 8.5.11 Battery temperature sensor
- 8.5.12 Cable compensation
- 8.5.13 PV string connection
- 8.5.14 Expert menu
- 8.6 Li-Ion battery system functions (MPPT 6000-M only)
- 8.7 NiCd battery system functions (MPPT 6000-M only)
- 8.8 StecaLink bus
- 8.9 Internal data logger
- 8.10 Clear log data
- 8.11 Clear event log
- 8.12 Factory settings
- 8.13 UART/RS-232 interface (MPPT 6000-M only)
- 8.14 Acoustic alarm
- 8.15 SD card (MPPT 6000-M only)
- 9 Control functions via AUX 1/2/3 (MPPT 6000-M only)
- 10 Troubleshooting
- 11 Maintenance, dismounting and disposal
- 12 Technical data
- 13 Guarantee conditions, exclusion of liability, contacts, notes
7.3 Status display
The status display consists of the basic settings, the pages with the measurements and the
information bar.
Basic settings
The figures show the respective basic settings when battery charging
is switched on (top left) and when the charging is switched off
(bottom left).
①
The Solar module/system symbol shows the status of the solar
module and the system as follows:
The solar module is illuminated, the controller has detected the
Day condition. There are no event messages of type
Information
1)
present.
The solar module is illuminated, the controller has detected the
Day condition. An event message of type Warning
1)
or Error
1)
is present.
The solar module is not illuminated, the controller has detected
the Night condition. There are no event messages of type
Information
1)
present.
The solar module is not illuminated, the controller has detected
the Night condition. An event message of type Warning
1)
or
Error
1)
is present.
1)
See
Ä
Chapter 10.2.2 ‘Function’ on page 111 for more
information.
②
The Battery symbol indicates charging of the battery as follows:
Battery almost full
Battery almost empty
③
Actual power currently being used by the MPPT 6000-M/-S for
charging the battery.
④
Battery charge current of the MPPT 6000-M/-S.
⑤
Display of the battery voltage in volts or the state of charge
(SOC) in %.
The battery voltage is displayed in volts when the battery
control mode is set to voltage control. The state of charge
(SOC) is displayed when the battery control mode is set to state
of charge (SOC).
The SOC value can only be displayed by the MPPT 6000-M.
756.404 | Z01 | 16.06
53