User manual
Table Of Contents
- 1 General information
- 2 Quick guide
- 3 Overview
- 4 Installation of the base system
- 5 Initial commissioning of the base system
- 6 Installation and initial commissioning of optional components
- 6.1 Commissioning the SD card (MPPT 6000-M only)
- 6.2 AUX 1,2,3 relay output connection (MPPT 6000-M only)
- 6.3 AUX IO remote control input connection (MPPT 6000-M only)
- 6.4 PA TS-S external temperature sensor connection
- 6.5 StecaLink slave connection
- 6.6 StecaLink master connection (MPPT 6000-M only)
- 6.7 UART/RS-232 interface connection (MPPT 6000-M only)
- 6.8 Redundancy function (MPPT 6000-S only)
- 6.9 Install cable strain relief
- 7 Display (layout, function, operation)
- 8 System functions
- 8.1 Protection functions
- 8.2 Battery type setting
- 8.3 Current limit system setting (MPPT 6000-M only)
- 8.4 Current limit device setting
- 8.5 Lead-acid battery system functions
- 8.5.1 Equalisation cycle mode
- 8.5.2 Battery control mode (MPPT 6000-M only)
- 8.5.3 Battery capacity test (MPPT 6000-M only)
- 8.5.4 Battery type
- 8.5.5 Battery capacity
- 8.5.6 Current limit system (MPPT 6000-M only)
- 8.5.7 Current limit device
- 8.5.8 Charge voltages
- 8.5.9 IUIA charge mode (MPPT 6000-M only)
- 8.5.10 Start boost charge
- 8.5.11 Battery temperature sensor
- 8.5.12 Cable compensation
- 8.5.13 PV string connection
- 8.5.14 Expert menu
- 8.6 Li-Ion battery system functions (MPPT 6000-M only)
- 8.7 NiCd battery system functions (MPPT 6000-M only)
- 8.8 StecaLink bus
- 8.9 Internal data logger
- 8.10 Clear log data
- 8.11 Clear event log
- 8.12 Factory settings
- 8.13 UART/RS-232 interface (MPPT 6000-M only)
- 8.14 Acoustic alarm
- 8.15 SD card (MPPT 6000-M only)
- 9 Control functions via AUX 1/2/3 (MPPT 6000-M only)
- 10 Troubleshooting
- 11 Maintenance, dismounting and disposal
- 12 Technical data
- 13 Guarantee conditions, exclusion of liability, contacts, notes
6 Installation and initial commissioning of optional
components
Topics
1.
Ä
Chapter 6.1 ‘Commissioning the SD card (MPPT 6000-M only)’ on page 40
2.
Ä
Chapter 6.2 ‘AUX 1,2,3 relay output connection (MPPT 6000-M only)’ on page 41
3.
Ä
Chapter 6.3 ‘AUX IO remote control input connection (MPPT 6000-M only)’ on page 41
4.
Ä
Chapter 6.4 ‘PA TS-S external temperature sensor connection’ on page 43
5.
Ä
Chapter 6.5 ‘StecaLink slave connection’ on page 45
6.
Ä
Chapter 6.6 ‘StecaLink master connection (MPPT 6000-M only)’ on page 48
7.
Ä
Chapter 6.7 ‘UART/RS-232 interface connection (MPPT 6000-M only)’ on page 50
8.
Ä
Chapter 6 ‘Installation and initial commissioning of optional components’ on page 40
9.
Ä
Chapter 6.9 ‘Install cable strain relief’ on page 51
6.1 Commissioning the SD card (MPPT 6000-M only)
CAUTION!
Never forcibly insert or remove the microSD card. This can damage the card holder and/or the
microSD card.
NOTICE!
– A microSD card is not included in the scope of delivery for the device.
–
microSD and microSDHC cards with a capacity of up to 8 GB can be used.
– The microSD card must be formatted with a FAT16 or FAT32 file system.
– Data from the MPPT 6000-M and any connected StecaLink slave devices can be recorded
on the microSD card.
– Settings parameters for the MPPT 6000-M can be saved to and read from the microSD
card.
– Take care to observe the correct insertion direction, as shown on the microSD card and the
device.
– Carefully and gently push the microSD card into the opening in the device casing until it
latches into place.
– Remove the microSD card by pushing it further into the device until it unlatches, then let
go of the card and allow it to eject and finally pull the card out of the socket (Push-Pull
connector).
– Data recording onto the SD card is deactivated at the factory for newly delivered devices.
1. Insert a formatted microSD card.
2.
Configure the data logging function and save/load the parameters as described in
Ä
Chapter
8.15 ‘SD card (MPPT 6000-M only)’ on page 101.
756.404 | Z01 | 16.06
40