User manual
Table Of Contents
- 1 General information
- 2 Quick guide
- 3 Overview
- 4 Installation of the base system
- 5 Initial commissioning of the base system
- 6 Installation and initial commissioning of optional components
- 6.1 Commissioning the SD card (MPPT 6000-M only)
- 6.2 AUX 1,2,3 relay output connection (MPPT 6000-M only)
- 6.3 AUX IO remote control input connection (MPPT 6000-M only)
- 6.4 PA TS-S external temperature sensor connection
- 6.5 StecaLink slave connection
- 6.6 StecaLink master connection (MPPT 6000-M only)
- 6.7 UART/RS-232 interface connection (MPPT 6000-M only)
- 6.8 Redundancy function (MPPT 6000-S only)
- 6.9 Install cable strain relief
- 7 Display (layout, function, operation)
- 8 System functions
- 8.1 Protection functions
- 8.2 Battery type setting
- 8.3 Current limit system setting (MPPT 6000-M only)
- 8.4 Current limit device setting
- 8.5 Lead-acid battery system functions
- 8.5.1 Equalisation cycle mode
- 8.5.2 Battery control mode (MPPT 6000-M only)
- 8.5.3 Battery capacity test (MPPT 6000-M only)
- 8.5.4 Battery type
- 8.5.5 Battery capacity
- 8.5.6 Current limit system (MPPT 6000-M only)
- 8.5.7 Current limit device
- 8.5.8 Charge voltages
- 8.5.9 IUIA charge mode (MPPT 6000-M only)
- 8.5.10 Start boost charge
- 8.5.11 Battery temperature sensor
- 8.5.12 Cable compensation
- 8.5.13 PV string connection
- 8.5.14 Expert menu
- 8.6 Li-Ion battery system functions (MPPT 6000-M only)
- 8.7 NiCd battery system functions (MPPT 6000-M only)
- 8.8 StecaLink bus
- 8.9 Internal data logger
- 8.10 Clear log data
- 8.11 Clear event log
- 8.12 Factory settings
- 8.13 UART/RS-232 interface (MPPT 6000-M only)
- 8.14 Acoustic alarm
- 8.15 SD card (MPPT 6000-M only)
- 9 Control functions via AUX 1/2/3 (MPPT 6000-M only)
- 10 Troubleshooting
- 11 Maintenance, dismounting and disposal
- 12 Technical data
- 13 Guarantee conditions, exclusion of liability, contacts, notes
Set Set Set
Set
Set
Set Set
Set
Set
Set Set
Set
Set
Set
Set
Set
Set
Set
Set
Set
Set
Set
Set
Set
Set
Set
Set
Set
Set Set Set Set
[1s]
*1) MPPT 6000-M only
Battery settings Battery control mode
*1
Battery type
Battery capacity
NiCd battery settings *1
Bat. temperature s ensor
Sensor member list
Capacity
100 Ah
Upper charge voltage
U1
Temp. factor U1 (>0°C)
Fix DOD level
Charging time U1
D)
NiCd battery *1
[ ] MPPT 6000
[ ] HS400
[ ] ….
[ ] Lead acid battery
[ ] Lead Gel/AGM
[ ] Li-Ion battery *1
[ ] NiCd battery *1
Current limit system *1
Current limit device
On/Off [ ] On
[ ] Off
Value Limit
1605.0 A
Limit
60.0 A
Level charge voltage U1
1.50 V/cell
U1 tolerance for timer
DOD level charge reset
[ ] Internal
[ ] External
Limit for charge volt.
U1
Lower DOD limit
U1 factor per DOD
Temp. factor U1 (<0°C)
Lower charge voltage
U2
Temp. factor U2 (>0°C)
Temp. factor U2 (<0°C)
Number of NiCd cells
U2 U1 switch
Limit charge volt. U1
1.65 V/cell
Lower DOD limit value
0.05
Value U1 factor per DOD
5 mV
Value temp. factor U1
0.0 mV/K
Value temp. factor U1
-2.5 mV/K
DOD level
0.00
U1 tolerance level
50 mV
Duration charging time U1
50 min
DOD level charge reset
0.02
Level charge voltage U2
1.50 V/cell
Value temp. factor U2
0.0 mV/K
Value temp. factor U2
-2.5 mV/K
Number of NiCd cells
7
Voltage level
1.00 V/cell
Cable c ompensation [ ] On
[ ] Off
PV string connection
Expert menu Code
17038
Temp. compensation
[ ] separated
[ ] parallel
On/Off [ ] On
[ ] Off
756.404 | Z01 | 16.06
22