User manual
Table Of Contents
- 1 General information
- 2 Quick guide
- 3 Overview
- 4 Installation of the base system
- 5 Initial commissioning of the base system
- 6 Installation and initial commissioning of optional components
- 6.1 Commissioning the SD card (MPPT 6000-M only)
- 6.2 AUX 1,2,3 relay output connection (MPPT 6000-M only)
- 6.3 AUX IO remote control input connection (MPPT 6000-M only)
- 6.4 PA TS-S external temperature sensor connection
- 6.5 StecaLink slave connection
- 6.6 StecaLink master connection (MPPT 6000-M only)
- 6.7 UART/RS-232 interface connection (MPPT 6000-M only)
- 6.8 Redundancy function (MPPT 6000-S only)
- 6.9 Install cable strain relief
- 7 Display (layout, function, operation)
- 8 System functions
- 8.1 Protection functions
- 8.2 Battery type setting
- 8.3 Current limit system setting (MPPT 6000-M only)
- 8.4 Current limit device setting
- 8.5 Lead-acid battery system functions
- 8.5.1 Equalisation cycle mode
- 8.5.2 Battery control mode (MPPT 6000-M only)
- 8.5.3 Battery capacity test (MPPT 6000-M only)
- 8.5.4 Battery type
- 8.5.5 Battery capacity
- 8.5.6 Current limit system (MPPT 6000-M only)
- 8.5.7 Current limit device
- 8.5.8 Charge voltages
- 8.5.9 IUIA charge mode (MPPT 6000-M only)
- 8.5.10 Start boost charge
- 8.5.11 Battery temperature sensor
- 8.5.12 Cable compensation
- 8.5.13 PV string connection
- 8.5.14 Expert menu
- 8.6 Li-Ion battery system functions (MPPT 6000-M only)
- 8.7 NiCd battery system functions (MPPT 6000-M only)
- 8.8 StecaLink bus
- 8.9 Internal data logger
- 8.10 Clear log data
- 8.11 Clear event log
- 8.12 Factory settings
- 8.13 UART/RS-232 interface (MPPT 6000-M only)
- 8.14 Acoustic alarm
- 8.15 SD card (MPPT 6000-M only)
- 9 Control functions via AUX 1/2/3 (MPPT 6000-M only)
- 10 Troubleshooting
- 11 Maintenance, dismounting and disposal
- 12 Technical data
- 13 Guarantee conditions, exclusion of liability, contacts, notes
Set
Set Set
Set
Event log
E)
01/30 Event message
30/30 Event message
F)
Information
Contact info
System info
Manufacturer
Address
Email
QR code
Platform name
Serial num.
PU version
- APP
- FBL
- BFAPI
- HW
SYS version
- BFAPI
- FBL
- APP
- PAR
- HW
MPPT slave address
Manual
Set Set
Set Set
Set
Set
Set
Set
Set
Set Set
Set
Set
Set Set
Set
Set
Set
Set
Set
Set
Set
*1) MPPT 6000-M only
… further menu entries
depending on the Slave properties
… further menu entries
depending on the Slave properties
System settings Language
Time / date
Clear log data
Clear event log
Display settings
StecaLink slave addr.
StecaLink master menu
*1
Mode AUX IO
*1
RS-232 port
*1
Acoustic alarm
Factory reset
[ ] english
[ ] deutsch
[ ] ….
Time
Date
Time format
Date format
Time
00:00
Date
11.12.2015
[ ] yyyy-mm-dd
[ ] dd.mm.yyyy
[ ] mm/dd/yyyy
[ ] 12h
[ ] 24h
Are you sure?
[ ESC ] [ 1s ]
Contrast
Backlight
Value
50%
[ ] Off
[ ] Automatic
[ ] Power mode
RS485 address
1 - 99
Add slave device
Change slave settings
Delete slave
Synchronise
Set slave address 1
-99
[ ] MPPT 6000
[ ] HS400
[ ] ….
Synchronise all
slaves
[ ESC ] [ 1s ]
[ ] Ext. voltage on
[ ] Ext. voltage off
[ ] Ext. switch on
[ ] Ext. switch off
C)
Are you sure?
[ ESC ] [ 1s ]
[ ] MPPT 6000
[ ] HS400
[ ] ….
[ ] On
[ ] Off
[ ] On
[ ] Off
Reset all values
[ ESC ] [ 1s ]
756.404 | Z01 | 16.06
19