User manual
Table Of Contents
- 1 General information
- 2 Quick guide
- 3 Overview
- 4 Installation of the base system
- 5 Initial commissioning of the base system
- 6 Installation and initial commissioning of optional components
- 6.1 Commissioning the SD card (MPPT 6000-M only)
- 6.2 AUX 1,2,3 relay output connection (MPPT 6000-M only)
- 6.3 AUX IO remote control input connection (MPPT 6000-M only)
- 6.4 PA TS-S external temperature sensor connection
- 6.5 StecaLink slave connection
- 6.6 StecaLink master connection (MPPT 6000-M only)
- 6.7 UART/RS-232 interface connection (MPPT 6000-M only)
- 6.8 Redundancy function (MPPT 6000-S only)
- 6.9 Install cable strain relief
- 7 Display (layout, function, operation)
- 8 System functions
- 8.1 Protection functions
- 8.2 Battery type setting
- 8.3 Current limit system setting (MPPT 6000-M only)
- 8.4 Current limit device setting
- 8.5 Lead-acid battery system functions
- 8.5.1 Equalisation cycle mode
- 8.5.2 Battery control mode (MPPT 6000-M only)
- 8.5.3 Battery capacity test (MPPT 6000-M only)
- 8.5.4 Battery type
- 8.5.5 Battery capacity
- 8.5.6 Current limit system (MPPT 6000-M only)
- 8.5.7 Current limit device
- 8.5.8 Charge voltages
- 8.5.9 IUIA charge mode (MPPT 6000-M only)
- 8.5.10 Start boost charge
- 8.5.11 Battery temperature sensor
- 8.5.12 Cable compensation
- 8.5.13 PV string connection
- 8.5.14 Expert menu
- 8.6 Li-Ion battery system functions (MPPT 6000-M only)
- 8.7 NiCd battery system functions (MPPT 6000-M only)
- 8.8 StecaLink bus
- 8.9 Internal data logger
- 8.10 Clear log data
- 8.11 Clear event log
- 8.12 Factory settings
- 8.13 UART/RS-232 interface (MPPT 6000-M only)
- 8.14 Acoustic alarm
- 8.15 SD card (MPPT 6000-M only)
- 9 Control functions via AUX 1/2/3 (MPPT 6000-M only)
- 10 Troubleshooting
- 11 Maintenance, dismounting and disposal
- 12 Technical data
- 13 Guarantee conditions, exclusion of liability, contacts, notes
Signal/Information Value Units Action
RS-232 Data info 23 Energy input/total Ah Ah meter of the energy input members
total since initial commissioning
RS-232 Data info 24 Energy output 24 h Ah Ah meter of the energy output
members total during the period from
00:00 to 23:59
RS-232 Data info 25 Energy output/total Ah Ah meter of the energy output
members total since initial
commissioning
RS-232 Data info 26 Derating Ah 0- Derating not active, 1- Derating
active
RS-232 Data info 27 Checksum A CRC16 checksum is generated. Name:
‘CRC-16-CCITT/openUART’ Width: 16
Direction: right shift Polynomial:
0x8408 CCITT reversed, 2 bytes long,
stored as high-byte, low-byte. The CRC
is calculated with semicolons and
without CR+LF.
RS-232 Data info 28 End of data CR + LF
12.4 Recording data on an SD card (MPPT 6000-M only)
When data logging is activated, separate data logging files are created for each of the following
StecaLink member devices:
n MPPT 6000-M
n MPPT 6000-S
n PA HS400
The data files are stored in a predefined directors structure.
File name structure of the data files
‘StecaLink bus address’
+ ‘-’ + ‘Device name’ + ‘.CSV’
Example: 40-HS400.CSV or 08-MPPTS.CSV
756.404 | Z01 | 16.06
145