User manual
Table Of Contents
- 1 General information
- 2 Quick guide
- 3 Overview
- 4 Installation of the base system
- 5 Initial commissioning of the base system
- 6 Installation and initial commissioning of optional components
- 6.1 Commissioning the SD card (MPPT 6000-M only)
- 6.2 AUX 1,2,3 relay output connection (MPPT 6000-M only)
- 6.3 AUX IO remote control input connection (MPPT 6000-M only)
- 6.4 PA TS-S external temperature sensor connection
- 6.5 StecaLink slave connection
- 6.6 StecaLink master connection (MPPT 6000-M only)
- 6.7 UART/RS-232 interface connection (MPPT 6000-M only)
- 6.8 Redundancy function (MPPT 6000-S only)
- 6.9 Install cable strain relief
- 7 Display (layout, function, operation)
- 8 System functions
- 8.1 Protection functions
- 8.2 Battery type setting
- 8.3 Current limit system setting (MPPT 6000-M only)
- 8.4 Current limit device setting
- 8.5 Lead-acid battery system functions
- 8.5.1 Equalisation cycle mode
- 8.5.2 Battery control mode (MPPT 6000-M only)
- 8.5.3 Battery capacity test (MPPT 6000-M only)
- 8.5.4 Battery type
- 8.5.5 Battery capacity
- 8.5.6 Current limit system (MPPT 6000-M only)
- 8.5.7 Current limit device
- 8.5.8 Charge voltages
- 8.5.9 IUIA charge mode (MPPT 6000-M only)
- 8.5.10 Start boost charge
- 8.5.11 Battery temperature sensor
- 8.5.12 Cable compensation
- 8.5.13 PV string connection
- 8.5.14 Expert menu
- 8.6 Li-Ion battery system functions (MPPT 6000-M only)
- 8.7 NiCd battery system functions (MPPT 6000-M only)
- 8.8 StecaLink bus
- 8.9 Internal data logger
- 8.10 Clear log data
- 8.11 Clear event log
- 8.12 Factory settings
- 8.13 UART/RS-232 interface (MPPT 6000-M only)
- 8.14 Acoustic alarm
- 8.15 SD card (MPPT 6000-M only)
- 9 Control functions via AUX 1/2/3 (MPPT 6000-M only)
- 10 Troubleshooting
- 11 Maintenance, dismounting and disposal
- 12 Technical data
- 13 Guarantee conditions, exclusion of liability, contacts, notes
Internal data logger
Energy input recording Last 18h | 30 Days | 12 Months | 20 Years |
Total
Energy output recording
(MPPT 6000-M only)
Last 18h | 30 Days | 12 Months | 20 Years |
Total
Recording of max./min. values Minimum battery voltage | 30 days
Maximum battery voltage | 30 days
Maximum device charge current | 30 days
Maximum device PV 1 voltage| 30 days
Maximum device PV 2 voltage| 30 days
Internal event log
Scope of event log 30 messages
System
Language
Factory setting English
Setting range English/German/French/Italian/Spanish/
Portuguese
2)
Time and date
RTC data retention 4 days
Time setting 00:00 … 23:59 | 01:00 AM … 12:59 PM
Date setting 01.01.2010 … 31.12.2079
Time format setting 12 h | 24 h
Date format setting YYYY-MM-TT | TT.MM.YYYY | MM/TT/YYYY
Display settings
Contrast
Factory setting 50 %
Setting range 0 % to 100%
Backlighting
Factory setting Automatic
Setting range Off | Automatic | Power mode
StecaLink slave address
Factory setting 1
756.404 | Z01 | 16.06
135