User manual
Table Of Contents
- 1 General information
- 2 Quick guide
- 3 Overview
- 4 Installation of the base system
- 5 Initial commissioning of the base system
- 6 Installation and initial commissioning of optional components
- 6.1 Commissioning the SD card (MPPT 6000-M only)
- 6.2 AUX 1,2,3 relay output connection (MPPT 6000-M only)
- 6.3 AUX IO remote control input connection (MPPT 6000-M only)
- 6.4 PA TS-S external temperature sensor connection
- 6.5 StecaLink slave connection
- 6.6 StecaLink master connection (MPPT 6000-M only)
- 6.7 UART/RS-232 interface connection (MPPT 6000-M only)
- 6.8 Redundancy function (MPPT 6000-S only)
- 6.9 Install cable strain relief
- 7 Display (layout, function, operation)
- 8 System functions
- 8.1 Protection functions
- 8.2 Battery type setting
- 8.3 Current limit system setting (MPPT 6000-M only)
- 8.4 Current limit device setting
- 8.5 Lead-acid battery system functions
- 8.5.1 Equalisation cycle mode
- 8.5.2 Battery control mode (MPPT 6000-M only)
- 8.5.3 Battery capacity test (MPPT 6000-M only)
- 8.5.4 Battery type
- 8.5.5 Battery capacity
- 8.5.6 Current limit system (MPPT 6000-M only)
- 8.5.7 Current limit device
- 8.5.8 Charge voltages
- 8.5.9 IUIA charge mode (MPPT 6000-M only)
- 8.5.10 Start boost charge
- 8.5.11 Battery temperature sensor
- 8.5.12 Cable compensation
- 8.5.13 PV string connection
- 8.5.14 Expert menu
- 8.6 Li-Ion battery system functions (MPPT 6000-M only)
- 8.7 NiCd battery system functions (MPPT 6000-M only)
- 8.8 StecaLink bus
- 8.9 Internal data logger
- 8.10 Clear log data
- 8.11 Clear event log
- 8.12 Factory settings
- 8.13 UART/RS-232 interface (MPPT 6000-M only)
- 8.14 Acoustic alarm
- 8.15 SD card (MPPT 6000-M only)
- 9 Control functions via AUX 1/2/3 (MPPT 6000-M only)
- 10 Troubleshooting
- 11 Maintenance, dismounting and disposal
- 12 Technical data
- 13 Guarantee conditions, exclusion of liability, contacts, notes
NiCd battery settings (MPPT 6000-M only)
Temp. factor U1 (>0 °C)
Factory setting -2.5 mV/cell/K/cell
Setting range -6.0 mV/cell/K/cell … 0.0 mV/cell/K/cell
Fixed DOD value
Factory setting 0.00
Setting range 0.00 … 1.00
U1 tolerance for timer
Factory setting 50 mV
Setting range 0 mV … 100 mV
Charging time U1
Factory setting 50 min
Setting range 0 min … 600 min
DOD level charge reset
Factory setting 0.02
Setting range 0.00 … 0.10
Lower charge voltage U2
Factory setting 1.50 V/cell
Setting range 1.35 V/cell… 1.60 V/cell
Temp. factor U2 (>0 °C)
Factory setting 0.0 mV/cell/K/cell
Setting range -6.0 mV/cell/K/cell … 0.0 mV/cell/K/cell
Temp. factor U2 (<0 °C)
Factory setting -2.5 mV/cell/K/cell
Setting range -6.0 mV/cell/K/cell … 0.0 mV/cell/K/cell
Number of NiCd cells
Factory setting 7 cells
Setting range 6 … 50 cells
U2 U1 switch
Factory setting 1.0 V/cell
Setting range 1.0 V/cell… 1.8 V/cell
756.404 | Z01 | 16.06
129