User manual
Table Of Contents
- 1 General information
- 2 Quick guide
- 3 Overview
- 4 Installation of the base system
- 5 Initial commissioning of the base system
- 6 Installation and initial commissioning of optional components
- 6.1 Commissioning the SD card (MPPT 6000-M only)
- 6.2 AUX 1,2,3 relay output connection (MPPT 6000-M only)
- 6.3 AUX IO remote control input connection (MPPT 6000-M only)
- 6.4 PA TS-S external temperature sensor connection
- 6.5 StecaLink slave connection
- 6.6 StecaLink master connection (MPPT 6000-M only)
- 6.7 UART/RS-232 interface connection (MPPT 6000-M only)
- 6.8 Redundancy function (MPPT 6000-S only)
- 6.9 Install cable strain relief
- 7 Display (layout, function, operation)
- 8 System functions
- 8.1 Protection functions
- 8.2 Battery type setting
- 8.3 Current limit system setting (MPPT 6000-M only)
- 8.4 Current limit device setting
- 8.5 Lead-acid battery system functions
- 8.5.1 Equalisation cycle mode
- 8.5.2 Battery control mode (MPPT 6000-M only)
- 8.5.3 Battery capacity test (MPPT 6000-M only)
- 8.5.4 Battery type
- 8.5.5 Battery capacity
- 8.5.6 Current limit system (MPPT 6000-M only)
- 8.5.7 Current limit device
- 8.5.8 Charge voltages
- 8.5.9 IUIA charge mode (MPPT 6000-M only)
- 8.5.10 Start boost charge
- 8.5.11 Battery temperature sensor
- 8.5.12 Cable compensation
- 8.5.13 PV string connection
- 8.5.14 Expert menu
- 8.6 Li-Ion battery system functions (MPPT 6000-M only)
- 8.7 NiCd battery system functions (MPPT 6000-M only)
- 8.8 StecaLink bus
- 8.9 Internal data logger
- 8.10 Clear log data
- 8.11 Clear event log
- 8.12 Factory settings
- 8.13 UART/RS-232 interface (MPPT 6000-M only)
- 8.14 Acoustic alarm
- 8.15 SD card (MPPT 6000-M only)
- 9 Control functions via AUX 1/2/3 (MPPT 6000-M only)
- 10 Troubleshooting
- 11 Maintenance, dismounting and disposal
- 12 Technical data
- 13 Guarantee conditions, exclusion of liability, contacts, notes
12 Technical data
Topics
1.
Ä
Chapter 12.1 ‘Controller’ on page 124
2.
Ä
Chapter 12.2 ‘Connection cable’ on page 138
3.
Ä
Chapter 12.3 ‘UART/RS-232 interface protocol (MPPT 6000-M only)’ on page 142
4.
Ä
Chapter 12.4 ‘Recording data on an SD card (MPPT 6000-M only)’ on page 145
5.
Ä
Chapter 12.4.1 ‘MPPT 6000-M data file’ on page 146
6.
Ä
Chapter 12.4.2 ‘TIMECHG data file’ on page 148
7.
Ä
Chapter 12.4.3 ‘PA HS400 data file’ on page 148
8.
Ä
Chapter 12.4.4 ‘MPPT 6000-S data file’ on page 149
12.1 Controller
NOTICE!
The respective values for system voltages of 12 V, 24 V, 36 V, 48 V and 60 V are separated with
a "/" character in the following text.
Technical data at 25 °C / 77 °F
Characterisation of the operating behaviour MPPT 6000-M/MPPT 6000-S
Supply voltage for operation (battery voltage)
Minimum 9.5 VDC
Maximum 80.0 VDC
System voltage range 12 V/24 V/48 V (automatic detection)
36 V/60 V (manually set)
System voltage setting
Factory setting Automatic
Setting range Automatic/12 V/24 V/36 V/48 V/60 V
String connection
Factory setting Separated
Setting range Separated/Parallel
Total rated output 900 W/1800 W/3600 W; [at battery voltages of
15 V, 30 V, 60 V]
756.404 | Z01 | 16.06
124