User manual
Table Of Contents
- 1 General information
- 2 Quick guide
- 3 Overview
- 4 Installation of the base system
- 5 Initial commissioning of the base system
- 6 Installation and initial commissioning of optional components
- 6.1 Commissioning the SD card (MPPT 6000-M only)
- 6.2 AUX 1,2,3 relay output connection (MPPT 6000-M only)
- 6.3 AUX IO remote control input connection (MPPT 6000-M only)
- 6.4 PA TS-S external temperature sensor connection
- 6.5 StecaLink slave connection
- 6.6 StecaLink master connection (MPPT 6000-M only)
- 6.7 UART/RS-232 interface connection (MPPT 6000-M only)
- 6.8 Redundancy function (MPPT 6000-S only)
- 6.9 Install cable strain relief
- 7 Display (layout, function, operation)
- 8 System functions
- 8.1 Protection functions
- 8.2 Battery type setting
- 8.3 Current limit system setting (MPPT 6000-M only)
- 8.4 Current limit device setting
- 8.5 Lead-acid battery system functions
- 8.5.1 Equalisation cycle mode
- 8.5.2 Battery control mode (MPPT 6000-M only)
- 8.5.3 Battery capacity test (MPPT 6000-M only)
- 8.5.4 Battery type
- 8.5.5 Battery capacity
- 8.5.6 Current limit system (MPPT 6000-M only)
- 8.5.7 Current limit device
- 8.5.8 Charge voltages
- 8.5.9 IUIA charge mode (MPPT 6000-M only)
- 8.5.10 Start boost charge
- 8.5.11 Battery temperature sensor
- 8.5.12 Cable compensation
- 8.5.13 PV string connection
- 8.5.14 Expert menu
- 8.6 Li-Ion battery system functions (MPPT 6000-M only)
- 8.7 NiCd battery system functions (MPPT 6000-M only)
- 8.8 StecaLink bus
- 8.9 Internal data logger
- 8.10 Clear log data
- 8.11 Clear event log
- 8.12 Factory settings
- 8.13 UART/RS-232 interface (MPPT 6000-M only)
- 8.14 Acoustic alarm
- 8.15 SD card (MPPT 6000-M only)
- 9 Control functions via AUX 1/2/3 (MPPT 6000-M only)
- 10 Troubleshooting
- 11 Maintenance, dismounting and disposal
- 12 Technical data
- 13 Guarantee conditions, exclusion of liability, contacts, notes
3 Overview
3.1
Controller power unit
NOTICE!
The power unit connector assignments of the MPPT 6000-M and MPPT 6000-S are identical.
The MPPT 6000-M and MPPT 6000-S differ in the additional components that can be
connected.
+
+
-
-
M1+
M1-
M2+
M2-
M1+
M1-
PE
B+
B-
M2-
M2+
TEMP
BAT+/-
+/-
TEMP
TEMP
M1+
M1-
M2-
M2+
B-
B+
B
AT+/-
B-
B+
PE
BAT+/-
ཱི
ཱི
ཱི
ཱ
ི
ུ
ཱུ ྲྀ
ླྀ
ཹ
ཽ
ེ
ོ
ཻ
ཷ
ཾ
Fig. 2: Overview of the casing and connections on the power units for the MPPT 6000-M and MPPT
6000-S
Component Description
1 Display
2 Operating buttons
ESC, D, Ñ, SET
3 2 x RJ45 sockets for StecaLink slave
(MPPT 6000-S)
Service interface for technical professionals,
connection to an MPPT 6000-M and connection
to additional StecaLink expansion devices such
as (e.g.) the PA HS400.
756.404 | Z01 | 16.06
11