User manual
Table Of Contents
- 1 General information
- 2 Quick guide
- 3 Overview
- 4 Installation of the base system
- 5 Initial commissioning of the base system
- 6 Installation and initial commissioning of optional components
- 6.1 Commissioning the SD card (MPPT 6000-M only)
- 6.2 AUX 1,2,3 relay output connection (MPPT 6000-M only)
- 6.3 AUX IO remote control input connection (MPPT 6000-M only)
- 6.4 PA TS-S external temperature sensor connection
- 6.5 StecaLink slave connection
- 6.6 StecaLink master connection (MPPT 6000-M only)
- 6.7 UART/RS-232 interface connection (MPPT 6000-M only)
- 6.8 Redundancy function (MPPT 6000-S only)
- 6.9 Install cable strain relief
- 7 Display (layout, function, operation)
- 8 System functions
- 8.1 Protection functions
- 8.2 Battery type setting
- 8.3 Current limit system setting (MPPT 6000-M only)
- 8.4 Current limit device setting
- 8.5 Lead-acid battery system functions
- 8.5.1 Equalisation cycle mode
- 8.5.2 Battery control mode (MPPT 6000-M only)
- 8.5.3 Battery capacity test (MPPT 6000-M only)
- 8.5.4 Battery type
- 8.5.5 Battery capacity
- 8.5.6 Current limit system (MPPT 6000-M only)
- 8.5.7 Current limit device
- 8.5.8 Charge voltages
- 8.5.9 IUIA charge mode (MPPT 6000-M only)
- 8.5.10 Start boost charge
- 8.5.11 Battery temperature sensor
- 8.5.12 Cable compensation
- 8.5.13 PV string connection
- 8.5.14 Expert menu
- 8.6 Li-Ion battery system functions (MPPT 6000-M only)
- 8.7 NiCd battery system functions (MPPT 6000-M only)
- 8.8 StecaLink bus
- 8.9 Internal data logger
- 8.10 Clear log data
- 8.11 Clear event log
- 8.12 Factory settings
- 8.13 UART/RS-232 interface (MPPT 6000-M only)
- 8.14 Acoustic alarm
- 8.15 SD card (MPPT 6000-M only)
- 9 Control functions via AUX 1/2/3 (MPPT 6000-M only)
- 10 Troubleshooting
- 11 Maintenance, dismounting and disposal
- 12 Technical data
- 13 Guarantee conditions, exclusion of liability, contacts, notes
CAUTION!
Check the correct system voltage before changing the system voltage setting and check all
device settings immediately after changing the system voltage setting. Incorrect settings can
damage the battery.
8.6 Li-Ion battery system functions (MPPT 6000-M only)
NOTICE!
– Ensure that all settings agree with the specifications provided by the manufacturer of the
Li-Ion battery. The initial default settings provided are not recommendations.
–
Observe the safety notices for the battery used.
– The scope of the Battery settings menu changes when the Li-Ion battery type is selected.
– When the Li-Ion battery type is selected, the possible settings for the following functions
assigned to the AUX 1/2/3 outputs also change:
– deep discharge protection,
– generator control,
– excess energy control.
8.6.1 Battery control mode
NOTICE!
For the Li-Ion battery type, the measurement sources to be used for determining the total
battery charge/discharge current are defined via the Battery control mode menu.
For the sensor member list settings, see
Ä
Chapter 8.5.2 ‘Battery control mode (MPPT 6000-
M only)’ on page 63.
8.6.2 Battery type
For information on switching between the lead-acid, lead-gel/AGM, Li-Ion and NiCd battery
types, see
Ä
Chapter 5 ‘Initial commissioning of the base system’ on page 33.
8.6.3 Battery capacity
For the battery capacity settings see
Ä
Chapter 5 ‘Initial commissioning of the base system’
on page 33.
8.6.4 Current limit system
For the current limit system setting, see
Ä
Chapter 8.3 ‘Current limit system setting (MPPT
6000-M only)’ on page 60.
756.404 | Z01 | 16.06
74