User manual
Table Of Contents
- 1 General information
- 2 Quick guide
- 3 Overview
- 4 Installation of the base system
- 5 Initial commissioning of the base system
- 6 Installation and initial commissioning of optional components
- 6.1 Commissioning the SD card (MPPT 6000-M only)
- 6.2 AUX 1,2,3 relay output connection (MPPT 6000-M only)
- 6.3 AUX IO remote control input connection (MPPT 6000-M only)
- 6.4 PA TS-S external temperature sensor connection
- 6.5 StecaLink slave connection
- 6.6 StecaLink master connection (MPPT 6000-M only)
- 6.7 UART/RS-232 interface connection (MPPT 6000-M only)
- 6.8 Redundancy function (MPPT 6000-S only)
- 6.9 Install cable strain relief
- 7 Display (layout, function, operation)
- 8 System functions
- 8.1 Protection functions
- 8.2 Battery type setting
- 8.3 Current limit system setting (MPPT 6000-M only)
- 8.4 Current limit device setting
- 8.5 Lead-acid battery system functions
- 8.5.1 Equalisation cycle mode
- 8.5.2 Battery control mode (MPPT 6000-M only)
- 8.5.3 Battery capacity test (MPPT 6000-M only)
- 8.5.4 Battery type
- 8.5.5 Battery capacity
- 8.5.6 Current limit system (MPPT 6000-M only)
- 8.5.7 Current limit device
- 8.5.8 Charge voltages
- 8.5.9 IUIA charge mode (MPPT 6000-M only)
- 8.5.10 Start boost charge
- 8.5.11 Battery temperature sensor
- 8.5.12 Cable compensation
- 8.5.13 PV string connection
- 8.5.14 Expert menu
- 8.6 Li-Ion battery system functions (MPPT 6000-M only)
- 8.7 NiCd battery system functions (MPPT 6000-M only)
- 8.8 StecaLink bus
- 8.9 Internal data logger
- 8.10 Clear log data
- 8.11 Clear event log
- 8.12 Factory settings
- 8.13 UART/RS-232 interface (MPPT 6000-M only)
- 8.14 Acoustic alarm
- 8.15 SD card (MPPT 6000-M only)
- 9 Control functions via AUX 1/2/3 (MPPT 6000-M only)
- 10 Troubleshooting
- 11 Maintenance, dismounting and disposal
- 12 Technical data
- 13 Guarantee conditions, exclusion of liability, contacts, notes
Set Set Set
Set
Set Set
Set
Set
Set
Set
Set Set
Set
Set
Set Set
Set
Set
Set Set
Set
Set
Set
Set
Set
Set Set Set
[1s]
Set
Set Set
*1) MPPT 6000-M only
*3) SOC Control mode only
Set
*5) Lead acid battery only
Set
*4) Voltage control mode only
Battery settings Equalisation cycle *5
Battery control mode
*1
Battery capacity test
*1
Battery type
Battery capacity
Charge voltages
IUIA charge mode
*1
Start boost charge
Bat. temperature s ensor
Cable c ompensation
PV string connection
Expert menu
On/Off
Cycle Duration
30 days
SOC control mode
Sensor member list
Capacity
100 Ah
Float charging
Boost c harging
Equalisation charging
*5
Cycle
Code
17038
Equal. charge duration
*5
Boost c harge duration
Temp. compensation
System voltage
Duration
240 min
Temperatur e coefficient
-4 mV/K/cell
D)
Leadacid/LeadGel/AGM
[ ] On
[ ] Off
[ ] State of charge (SOC)
[ ] Voltage control
[ ] MPPT 6000
[ ] HS400
[ ] ….
Charging deactivated !
Are you sure?
[ ESC ] [ 1s ]
[ ] Lead acid battery
[ ] Lead Gel/AGM
[ ] Li-Ion battery *1
[ ] NiCd battery *1
Current limit system *1
Current limit device
On/Off [ ] On
[ ] Off
Value Limit
1605.0 A
Limit
60.0 A
Float charge voltage
56.4 V
Starting threshold
SOC *3 / V *4
Boost c harge voltage
57.6 V
Starting threshold
SOC *3 / V *4
Equal. charge voltage
60.0 V
On/Off [ ] On
[ ] Off
Cycle
6 month
Are you sure?
[ ESC ] [ 1s ]
[ ] Internal
[ ] External
[ ] On
[ ] Off
[ ] separated
[ ] parallel
Duration
120 min
On/Off
Temp. coefficient
[ ] On
[ ] Off
[ ] Automatic
[ ] 12V
[ ] 24V
[ ] 36V
[ ] 48V
[ ] 60V
756.404 | Z01 | 16.06
20