GARMENT STEAMER INSTRUCTION MANUAL MODEL NO.
Dear customer: Thanks for choosing our garment steamer. For your convenience of operating the steamer correctly, please read the instructions carefully before operation. (No further notice in case of changing of technical parameter) The picture is only for reference.
Brief introduction As a high-grade ironing appliance, the product is applicable to such places as home, hotel. It has compact and light weight design, save storage space. It provides massive high temperature steam, can easily remove wrinkles in short time. It heats up just in short time. Large water tank can steam 40 minutes continuously. Inspection should be made before operation Get rid of blockage if it exists in the steam pipe and inlet & outlet water pipe.
Safety reminder ·Don’t use the product before reading the instructions. ·Careful with hot condensed water from steam vent before operation. ·Move vertically to avoid plane ironing which can lead to spray head’s spraying. ·Don’t put it (or be exposed to) in water or liquid. ·Operate the machine with care and keep it away from children ·Don’t add hot water into the water tank, which can cause the deformation of the water tank.
Accessory schematic diagram 6 Part number Name 1 Main body 2 Water tank 3 Steam pipe 4 Spray head 5 Fabric brush 6 Hanger with hook 7 Supporting pole 8 Trousers clamp
Accessory schematic diagram 7 Part number Name 9 Switch 10 Boiler 11 Steam pipe connector 12 Supporting pole hole 13 Drainage cap 14 Base
Installation and operation 1、Install two pieces of base on the bottom of the machine by driving two screws. It provides stability of the machine. 2、Insert the supporting pole into the body, and then screw it up with the knob. 3、Unfold the supporting poles to the proper height and fix them. 4、Place the hanger with hook on the top of the supporting pole, and unfold the hanger. 5、Insert the head of the steam pipe into the sheath, and screw it up according to the drawing direction .
Instructions of operation 1：Please make sure the power switch is off before start working. 2：Take out the water tank，turn off the tank nut on the bottom, fill the water into the tank(see picture 1), then tighten the nut(see picture 2). Pay attention to that only can fill cold water, not hot water. In order to extend the life of the machine, we suggest that you may use the water that does not contain minerals or distilled water. Put back the water tank, and make sure that the position is installed correctly.
Method of Steaming: 1: The effect of high temperature steam is to soften clothes fiber. If only rely on the steam from the spray head is hard to steam clothes smoothly. Gently pull the clothes surface flat and use the steam to soften clothes fiber is the key to steam the clothes. 2: Attach the spray head to the clothes surface closely, move the spray head up and down gently. Steam the area you need, meanwhile fix the clothes surface flat and smooth by pulling.
Excrete the remaining water in the machine In order to avoid that the user not to use the garment steamer for long time, the water inside will go bad, or provide environment for bacteria to grow. So, there is a drainage cap on the bottom, you can excrete redundant water after turn off the cap. To avoid the water come out from the outlet when using next time, please tighten the cap after the water is out.
Storage 1: Please make the telescopic pole to the shortest, then remove the hose and put it aside. 2: Take the water tank, and pour out remaining water and clean up, then put back. 3: Please open the drainage cap on the bottom and pour out remaining water. 4: Clean the hose joint with clean water, make the hose around on the telescopic pole. Put the spray head on the hook.
Trouble-shooting Facts Out of completely work Reason Solution 1.Electrical fault; 2. Attaching plug gets loose; Check and maintain professional staff by 3.Fuse burns out; 4.Power light doesn’t work Big noise inside the steam pipe with little steam out steam pipe gets bended under horizontal level Raise up steam pipe to let condensate water backflow into the machine Spray head leakage 1.Spray head fracture 2. Operate flatwise 1.Replace spray head 2.
Parameters: Rated voltage:110V Steam discharge:35g/min Rated Frequency:50/60Hz Output power:1300W Water tank capacity:1.4L Height of whole machine:155cm Length of supporting pole:120cm Steam pipe length:145cm Packing list NO. Parts Quantity No.
