5 Gazebo GZ4 Monte Carlo Aluminium Composite Roof Panels 6’8” 10’3” Assembly Instructions 12’6” 4’6” Systems Trading Corporation 450 7th Avenue Suite 2809, New York, NY 10123 Customer service: (877)782 4482 Email: easygrow@stcaustin.com www.stcny.
Introduction Thank you for purchasing the Gazebo GZ4. When properly assembled and maintained, this gazebo will provide many years of enjoyment! These instructions include helpful hints and important information needed to safely assemble and properly maintain the gazebo. Please read these instructions completely before you begin. Our patented gazebo has been designed for easy assembly. All steps can be completed by a team of four people. The assembly should take about two hours.
Table of Contents Safety Advice Introduction................................................. Table of Contents......................................... List of Parts.................................................. Step 1 Assembling the Corner Profiles................. Step 2 Attaching the Rails to the Corner Profiles... Step 3 Securing the Gazebo to the ground......... Step 4 Installing the Lower Roof gable Profiles.. Step 5 Assembling the Roof Top..............................
List of Parts The gazebo is shipped in four cartons. These cartons are heavy. Be careful when lifting them. Wear proper safety gear including work shoes, gloves and goggles. The parts are identified by removable stickers. Place all the parts for each step in staging areas, checking that you have all parts as you go. If any parts are missing or damaged, contact STC customer service before beginning assembly: Customer service: (877)782 4482 Email: easygrow@stcaustin.com No.
No. Profile Qty Step No. Profile Qty Step 4,5 19 8 5 30 1 5 31 8 5 32 1 5 33 8 7 34 T-shaped Connector 24 5,9 2 2 1 We included some extra screws and bolts for your convenience. Plastic Cap #2 2.5 72 7 Screw M6*12 2.5 96 6 Screw M6*18 48 1 Screw M6*25 www.stcny.
STEP 1 Assembling the Corner Profiles Place all the parts on a level surface. Make sure the pieces are in the correct positions before assembling. Carefully follow the order of assembly to ensure an easy installation. Wear proper safety gear including work shoes, gloves and goggles.
1.B Slide support frames (12) over lower end of corner profiles (1). Attach support plates (13) to corner profiles as shown, using four screws (29) for each plate. 1 1 12 13 29 Leave support frames (12) about 10”over lower end of all eight corner profiles (1) until step 3 (Securing the gazebo to the ground) 1 12 13 13 12 1 www.stcny.
STEP 2 Attaching the Rails to the Corner Profiles Components Rail (2) Outer Roof Connector (25) Screw M6*12 (27) 2.A x 16 x8 x8 Screw M6*18 (28) Plastic Cap #2 (26) x 64 Magnetic Hex Key (34) x1 x 64 Attach one outer roof connector (25) to each rail at pre-drilled screw holes, using screws (27). 27 25 25 2 VIEW FROM SIDE 25 2 VIEW FROM THE TOP ATTENTION: Attach roof connectors facing exactly in the directions shown. x8 www.stcny.
2.B Attach one roof rail (2) to two corner profiles (1) as shown, using screws (28) and supplied magnetic hex key (34) through holes in profile set. 26 28 2 2 26 28 26 1 28 1 2.C Close holes in profile set with plastic caps #2 (26). 2 1 26 1 Repeat step 2.B and 2.C to create four sets. www.stcny.
2.D Using 4 people, attach roof profile (2) to corner profiles (1). Fasten with four screws (28) and supplied magnetic hex key (34) on each side. Close holes in profile sets with plastic caps #2 (26). 2 28 26 1 2 2 1 1 1 1 ILLUSTRATION 2.E Using 4 people, continue attaching roof profiles (2) to corner profiles (1) to create the octagonal gazebo base. 45° 45° 45° 90° 90° 45° 135° IMPORTANT: After this step you should place the gazebo frame in its desired location.
STEP 3 Securing the Gazebo to the Ground 3.A Fasten the gazebo frame to the ground, using four spikes (35) for each support plate. Lower support frames (12) to cover support plates (13). Components 1 1 12 Ground spike (35) x 32 35 13 13 Optional Securing the Gazebo to a Concrete Floor or Wood Deck Components Concrete Floor: 1. Using a concrete drill, drill holes into the concrete floor, corresponding to the holes in support plates (13). 2.
STEP 4 Installing the Lower Roof Gable Profiles Towards center BOTTOM VIEW OF PROFILE (8) Towards outer edge Components ATTENTION: DO NOT ATTEMPT TO ASSEMBLE THIS ALONE ! 4.A Using screws (30) and nuts (31), connect roof gable profiles (8) to roof connectors (14) on top of all eight corner profiles (1). Roof Gable Profile (8) 2102mm x8 Screw (30) x 16 ATTENTION: Nut M6 (31) x 16 Roof profiles, roof panels and gables must be aligned properly during assembly to minimize any possibility of leaking.
STEP 5 Assembling the Roof Top Components Roof Gable Profile (6) 431mm Roof Top Profile (3) 431mm x8 Top Ring (20) Upper Roof Connector (19) x1 x8 x8 Inner Roof Connector (21) x8 BLACK SIDE Top Center Rail Connector (22) Roof Top Cover (15) x1 Screw (30) x 24 5.
5.C Using screws (30) and nuts (31), connect the eight roof gable profiles (6), to upper roof connectors (19) as shown. ATTENTION: Roof profiles, roof panels and gables must be aligned properly during assembly to minimize any possibility of leaking. 31 30 19 6 20 6 6 6 6 19 19 6 6 19 19 19 6 5.D 19 20 6 Using screws (28), connect top center rail connector (22) to roof gable profiles (6) as shown. 20 22 28 VIEW FROM BELOW www.stcny.
5.E Insert hook (16) through hole in center rail connector (22) from below, through tube (17) and washer (18) as shown. Screw into roof top cover (15) from below. 15 18 17 22 16 5.F Fit the eight roof panels (9) on top of roof profiles (6) with their black side towards the top as shown and fasten each panel with two screws (32) from below at outer end. IMPORTANT: Remove protective plastic from both sides of roof panels! 9 9 9 9 9 9 9 6 6 6 6 32 6 32 9 www.stcny.
5.G Place roof profiles (3) on top of roof profile (6). Align both profiles. Fasten with two screws (30) from below. 3 6 3 Connecting the upper and lower profiles 6 6 30 30 5.H Close off roof profiles (6,3) with eight plastic caps #1 (24). 24 VIEW FROM BELOW 24 24 24 3 24 VIEW FROM TOP www.stcny.
STEP 6 Connecting the Roof Top to the Roof Gable Profiles ATTENTION: DO NOT ATTEMPT TO ASSEMBLE THIS STEP ALONE, USE AT LEAST 4 PEOPLE! Components Screw (28) x 16 6.A Using screws (28) attach the roof top to roof profiles (8) from below (inside the gazebo). VIEW FROM BELOW ILLUSTRATION www.stcny.
STEP 7 Connecting the Horizontal Roof Profiles 7.A Attach T-connectors (23) to underside of roof gable profiles (8), using screws (27) as shown. Components T-shaped Connector (23) 8 x8 Roof Profile (7) 8 23 23 23 8 x8 Screw (27) x 24 23 8 8 23 27 8 VIEW FROM BELOW 7.B Attach roof gable profiles (7) to T-connectors (23), placing ends into cut-outs on gutter profiles (8) as shown. Fasten from inside the gazebo, using screws (27) as shown.
STEP 8 Installing the Roof Panels and Upper Roof Profiles IMPORTANT: Remove protective plastic from both sides of roof panels. Place with black surface toward the sun facing out when installing. 8.A Fit roof panel (10) on top of roof profiles (8) as shown.
8.C Place roof top profile (4) on top of roof gable profile (7) as shown and fasten with two screws (30) from below (inside gazebo). Connecting the upper and lower profiles 4 4 7 11 10 7 7 30 11 ILLUSTRATION VIEW FROM BELOW 8.D Fit second roof panel (10) on top of roof profiles (8) as shown. Fit second roof panel (11) on top of roof profiles (8) as shown and fasten with screw (32) from below to outer roof connector (25). 10 10 11 11 8 11 25 8 11 32 VIEW FROM BELOW ILLUSTRATION www.stcny.
8.E Place second roof top profile (4) on top of roof gable profile (7) as shown and fasten with two screws (30) from below (inside gazebo). 7 7 10 10 4 30 11 11 11 11 VIEW FROM BELOW ILLUSTRATION 8.F Place roof top profile (5) on top of roof gable profile (8), aligning the profiles at their outer end. Fasten with four screws (30) from below (inside gazebo). 10 8 10 11 11 5 11 VIEW FROM BELOW 11 ILLUSTRATION www.stcny.
8.G Continue steps 8A through 8F in a clock-wise direction as shown, until the last two panels: Place the upper roof panel (10), secure with two screws (32) from below. Place the lower roof panel (11), secure with three screws (32) from below. Place the horizontal roof top profile (4), fasten with two screws (30) from below. Place the top roof gable profile (5), fasten with four screws (30) from below. VIEW FROM TOP 11 11 11 10 10 11 10 10 10 11 10 10 11 11 8.
8.I Slightly lifting the roof gable profiles (5), place the lower roof panel (11) and secure with three screws (32) from below. Fasten the roof gable profiles (5) at their lower end with screws (30) from below. Place the horizontal roof profile (4) carefully from above as shown, fasten with two screws (30) from below. 4 ILLUSTRATION STEP 9 Installing the Plastic Caps 9 Components Close off roof profiles (5,8) with plastic caps #1 (24).
Gazebo GZ4 Monte Carlo Aluminium Composite Roof Panels Assembly Instructions WARRANTY: Warranty covers damage due to manufacturing defects only. Warranty does not cover weather inflicted damage (Force Majeure) and/or damages caused by not following assembly instructions and not adhering to warnings in manual. EasyGrow Visit: http://www.stcny.
