User Manual

WARNINGS
 •Wehighlyrecommendthisproductbeinstalledbyaqualiedprofessional.
 •Pleasedonotbegininstallationuntilyouhavethoroughlyreadand
understood these instructions.
 •Thismountsupportsdisplaymountingfrom22”to40”,VESA75X75,100x100,
200x100 & 200x200, and supports a maximum load of 80 lbs (36.4 kg).
 •Ensurethewallthatyouplantousewillsafelysupportfourtimesthe
combined weight of the mount and your chosen display.
 •Undernocircumstancesshouldthisproductbemountedtometalstuds.
 •Themanufacturerdoesnotacceptresponsibilityforincorrectinstallation.
SPECIFICATIONS
 •MaximumLoad:80lbs.(36.4kg)
 •DisplaySize:22”to40”
 •Extension:3’
 •Pan/SwivelRange:360°
 •TiltRange:+0°/-20°
TOOLS REQUIRED
 •PowerDrill
 •3/16”(5mm)DrillBit
 •5/16”(8mm)MasonryBit
 •PhillipsHeadScrewDriver
 •3/8”SocketHeadWrench
 •7/16”SocketHeadWrench
INSTALLATION INSTRUCTIONS
Step 1: Use Ceiling Plate to Mark Mounting Hole Locations
a. The use of a stud nder is highly recommended.
Step 2: Mount the Ceiling Plate
For Mounting on a Wood Joist (Fig 1)
 a.Pre-drilltwoholesintojoistusinga3/16”drillbit.
  Besuretodrillintothecenterofthejoists.
b. Insert two Lag Screws into holes through
the Ceiling Plate and tighten down.
WARNING: Tighten screws so that the
Ceiling Plate is rmly attached, but
do not over tighten. Over tightening
can damage the screws, greatly
reducing their holding strength.
c. Thread in extension pipe and
tighten set screws provided.
d. Install Ceiling Plate Cover (optional).
For Mounting on a Concrete Ceiling (Fig 2)
a. Pre-drillfourholesintoconcreteusing5/16”Masonrybit.InsertHexSleeveanchors
(not supplied) and tap in with hammer (per instructions with wall anchor).
  WARNING:WheninstallingCeilingPlateon cinder block, verify rst that you
  haveaminimumof1-3/8”ofconcretethicknesstobeusedfortheConcrete
  WallAnchors(notincluded).Donotdrillintomortarjoints!Besuretomount
  inasolidpartoftheblock,generally1”minimumfromthesideofthe
block. Cinder block must meet ASTM C-90 specications. It is suggested
that a standard electric drill on slow setting
is used to drill the hole instead of a hammer
drill to avoid breaking out the back of the
hole when entering a void or cavity.
Concrete must be 2000 psi density
minimum. Lighter density concrete
may not hold concrete anchor.
Make sure that the supporting surface will
safely support the combined load of the
  equipmentandallattachedhardware
and components.
b. Remove washer and nut from end of bolt from
all four bolts. Place Ceiling Plate over bolts so they
align with the four holes in Ceiling Plate.
c. Re-install washer and nut onto end of bolt and tighten down
  usinga7/16”socketheadwrenchuntilsecure(perinstructions
with wall anchor). WARNING: Tighten nuts so that ceiling plate is rmly attached,
but do not over tighten. Over tightening can damage the bolts, greatly reducing their
holding strength.
HARDWARE KIT (T/DT)
M4 x 12mm Philips
Head Screw (x4/8)
M6 x 12mm Philips
Head Screw (x4/8)
M8 x 14mm Philips
Head Screw (x4/8)
Allen Wrench, 2.5mm,
Security/Non-Security (x2)
Allen Wrench, 4mm (x1)
M4 x 30mm Philips
Head Screw (x4/8)
M5 x 30mm Philips
Head Screw (x4/8)
M6 x 30mm Phillips
Head Screw (x4/8)
M5 x 12mm Philips
Head Screw (x4/8)
M6 x 20mm Philips
Head Screw (x4/8)
M6 (17.8 x 6.5 x 1.5mm)
Metal Washer (x4/8)
BOX CONTENTS (T/DT):
 •CeilingPlate(1)
 •CeilingPlateCover(1)
 •MountHead(1)
 •AdapterPlate(1/2)
 •Hardwarekit(1)
 •3’FixedExtensionPole(1)
Fig 1
Fig 2
#14 x 2.5” Lag Screw (x4)
M8 (20.5 x 8.5 x 2mm)
Metal Washer (x8/16)
M4/M5/M6 spacer:
12mm (x4)
M5 x 5mm Set Screw (x4)
M5 x 5mm Set Screw,
Security (x4)
Concreteanchorsnotprovided.5/16”x2-1/2”RedHead®HexSleeveAnchors,#50113,
are recommended for concrete or cinder block installation.
CAUTION:
These ceiling mounts are
intended for use only with
the maximum weight of
80 lbs (36.4kg).