User guide

WARNINGS
 •Wehighlyrecommendthisproductbeinstalledbyaqualiedprofessional.
 •Pleasedonotbegininstallationuntilyouhavethoroughlyreadand
understood these instructions.
 •Thismountsupportsdisplaymountingfrom22”to40”,VESA75X75,100x100,
200x100 & 200x200, and supports a maximum load of 80 lbs (36.4 kg).
 •Ensurethewallthatyouplantousewillsafelysupportfourtimesthe
combined weight of the mount and your chosen display.
 •Undernocircumstancesshouldthisproductbemountedtometalstuds.
 •Themanufacturerdoesnotacceptresponsibilityforincorrectinstallation.
SPECIFICATIONS
 •MaximumLoad:80lbs.(36.4kg)
 •DisplaySize:22”to40”
 •MaximumExtension:15.4”
 •Wiremanagement
 •Pan/SwivelRange:270°
 •TiltRange:+5°/-15°
 •Roll:+/-2.5°
BOX CONTENTS
 •WallArmAssembly(1)
 •AdapterPlate(1)
 •Hardwarekit(1)
INSTALLATION INSTRUCTIONS
Step 1: Use Wall Plate to Mark Mounting Hole Locations
a. The use of a stud nder is highly recommended.
Step 2: Mount the Wall Arm Assembly
For Mounting on a Stud Wall (Fig 1)
 a.Pre-drilltwoholesintostudusinga3/16”drillbit.
Be sure to drill into the center of the studs.
b. Insert two Wood Screws into holes through
the Wall Plate and tighten down. Be sure the
Wall Arm Assembly is mounted with the
key slots pointing upwards
WARNING: Tighten screws so that the
Wall Plate is rmly attached, but
do not over tighten. Over tightening
can damage the screws, greatly
reducing their holding strength.
c. (Optional) Attach Screw Covers over
head of screws.
For Mounting on a Concrete Wall (Fig 2)
 a.Pre-drilltwoholesintoconcreteusing5/16”drill bits. Insert Concrete Wall
Anchors and tap in with hammer, if necessary.
  WARNING:WheninstallingWallArmAssemblyon cinder block, verify rst that
  youhaveaminimumof1-3/8”ofconcretethicknesstobeusedforthe
Concrete Wall Anchors. Do not drill into mortar joints! Be sure to mount in
  asolidpartoftheblock,generally1”minimumfromthesideoftheblock.
Cinder block must meet ASTM C-90 specications. It is suggested that a
standard electric drill on slow setting is used to drill the hole instead of a
hammer drill to avoid breaking out the back of the hole when entering
a void or cavity.
Concrete must be 2000 psi density
minimum. Lighter density concrete
may not hold concrete anchor.
Make sure that the supporting surface
will safely support the combined load
  oftheequipmentandallattached
hardware and components.
b. Insert two Wood Screws into the
Wall Anchors through the Wall
Plate. Be sure the Wall Arm
Assembly is mounted with the
key slots pointing upwards.
WARNING: Tighten screws so that wall plate is rmly attached, but do not
over tighten. Over tightening can damage the screws, greatly reducing their
holding strength.
c. (Optional) Attach Screw Covers over head of screw.
HARDWARE KIT
M4 x 12mm Philips
Head Screw (x4)
M6 x 12mm Philips
Head Screw (x4)
M8 x 14mm Philips
Head Screw (x4)
4” Wire Tie (x4)
Allen Wrench, 4mm (x1)
Concrete Wall Anchor (x2)
Screw Cover (x2)
M4 x 30mm Philips
Head Screw (x4)
M5 x 30mm Philips
Head Screw (x4)
M6 x 30mm Phillips
Head Screw (x4)
M5 x 12mm Philips
Head Screw (x4)
M6 x 20mm Philips
Head Screw (x4)
M6 (17.8 x 6.5 x 1.5mm)
Metal Washer (x4)
M8 (20.5 x 8.5 x 2mm)
Metal Washer (x8)
TOOLS REQUIRED
 •PowerDrill
 •3/16”(5mm)DrillBit
 •5/16”(8mm)MasonryBit
 •PhillipsHeadScrewDriver
 •Level
Fig 1
Fig 2
# 14x2.5” Philips
Wood Screw (x2)
Screw Cover Wood Screw
Concrete Anchor
M4/M5/M6 spacer:
12mm (x4)
CAUTION:
This wall mount is intended
for use only with the maximum
weight of 80 lbs (36.4kg).