Manual

ManualsBrandsStaub Electronics ManualsAccessories for electricalKIT-IR-RPTR-2X6 EPISODE - ELECTRONICS 2X6 IR REPEATER WITH POWER SUPPLY

OWNER’S MANUAL >>IR REPEATERS

IR1X4 IR2X6

1. Introduction ....................................................2

2. Installation......................................................2

2.1. Basic Connections (1/8” – 3.5mm Jacks) .....2

2.2. Advanced Connections .................................3

,5;,55HFHLYHU,QSXW&RQ¿JXUDWLRQ .....4

7URXEOHVKRRWLQJ ............................................ 4

6SHFL¿FDWLRQV ................................................5

4. Warranty .........................................................6

5. Contacting Technical Support......................6

TABLE OF CONTENTS

Summary of content (6 pages)

PAGE 1
OWNER’S MANUAL IR1X4 >>IR REPEATERS IR2X6 TABLE OF CONTENTS 1. Introduction.................................................... 2 2. Installation...................................................... 2 2.1. Basic Connections (1/8” – 3.5mm Jacks) ..... 2 2.2. Advanced Connections ................................. 3 ,5 ; ,5 5HFHLYHU ,QSXW &RQ¿JXUDWLRQ ..... 4 7URXEOHVKRRWLQJ ............................................ 4 6SHFL¿FDWLRQV ................................................ 5 4.
PAGE 2
1. INTRODUCTION Episode is one of the most highly-regarded brands of electronics equipment available today. We appreciate your business and we stand committed to providing our customers with the highest degree of quality and service in the industry. 2. INSTALLATION 2.1. BASIC CONNECTIONS (1/8” – 3.5MM JACKS) 1. Connect an IR Receiver to the IR Receiver In (IR A or IR B on IR2X6). Note: Do not connect the IR Receiver to an IR Emitter connection as damage to the Receiver may occur. 2.
PAGE 3
2.2. ADVANCED CONNECTIONS When using the IR Receiver located in a remote location, the screw terminals can be used to extend the cable attached to the IR Receiver. When using the screw terminals, proper polarity MUST be maintained in order to avoid damaging the IR Receiver. The screw connections are also useful when connecting to the output of a control system. Note: When connecting to a control system, the +12VDC is not used.
PAGE 4
LONG CABLE RUNS When using long lengths of cable (>50 ft.), it may be necessary to connect a 470 Ohm 1/8 Watt resistor between IR IN (signal) and GND. The resistor discharges the cable capacitance, which allows high bit-rate IR codes to work with higher reliability. IR ConnectinJ Block Terminals GND IR SiJnal SIGNAL 470 Ohm 1/8 Watt Resistor +1 2V GND 12V DC 2.2.1.
PAGE 5
3. SPECIFICATIONS IR1X4 INPUTS (1) 1/8” 3.5MM JACK (1) 4 SCREW TERMINAL PLUG OUTPUTS (4) 1/8” 3.5MM JACKS POWER +12VDC 10MA DIMENSIONS 2” (50.8MM) H X 4” (101.6MM) W X 1” (25.4MM) D IR2X6 INPUTS (2) 1/8” 3.5MM JACK (2) 4 SCREW TERMINAL PLUG OUTPUTS (6) 1/8” 3.5MM JACKS POWER +12VDC 10MA DIMENSIONS 2” (50.8MM) H X 4.875” (123.83MM) W X 1” (25.
PAGE 6
4. WARRANTY 3-Year Limited Warranty 3 YEAR Episode® Electronics Products have a 3-Year Limited Warranty. This warranty includes parts and labor repairs on all components found to be defective in material or workmanship under normal conditions of use.