Installation Manual B-500-RX-230-IR HDBaseT Matrix Receiver
B-500-RX-230-IR Installation Manual Important Safety Instructions WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. Do not remove cover. No user serviceable parts inside. Refer servicing to qualified service personnel. 1. Read and follow all instructions and warnings in this manual. Keep for future reference. 2. Do not use this apparatus near water. 3. Clean only with a dry cloth. 4. Do not block any ventilation openings.
B-500-RX-230-IR Installation Manual 1. Table of Contents 2. Product Overview...................................................................................................4 2.1. Features............................................................................................................4 2.2. Package Contents.............................................................................................4 3. Recommended for Installation................................................................
B-500-RX-230-IR Installation Manual 2. Product Overview The B-500-RX-230-IR extends HDMI over a single Cat5e/6 using HDBaseT technology allowing video and audio transmission to remote displays from any HDBaseT Transmitter including the B-500MTRX-230 family of HDBaseT matrix switchers. The B-500-RX-230-IR supports all HDMI defined Audio and Video formats, including 3D Video and 4K, and features bi-directional IR pass-through. 2.1.
B-500-RX-230-IR Installation Manual 4. Receiver Layout 1 2 3 4 5 6 7 8 1. HDMI Out Attach HDMI cable to the display. 2. IR Receiver Connect an IR receiver to this port for capturing commands to transmit IR signal to the matrix switcher using IR pass-through. (3.5mm stereo mini) 3. IR Flasher Connect an IR flasher or control system to this port to control a display or device using IR pass-through. (3.5mm mono mini) 4.
B-500-RX-230-IR Installation Manual 5. Wiring Recommendations 5.1. HDBaseT Link Cable Type - Shielded or Unshielded Cat5e/6 • Distance Limitations Cat5e/ Cat6: Up to 200ft (4K x 2K resolution is limited to 115 ft) Cat6a: Up to 230ft (4K x 2K resolution is limited to 130 ft) • Use at least Category 5e high quality twisted pair solid conductor cable rated to 350 Mhz bandwidth. The higher the cable standard, the better it will perform. • For the best results install a shielded cable.
B-500-RX-230-IR Installation Manual 5.2. HDMI Cable • Use Binary (or similar) 2 meter or shorter, High Speed rated HDMI cables between any device and the HDMI output port of the Receiver for the best performance. • The Receiver should work with a longer cable, but in the case of any picture or sync issues, it should be 2 meters or less between the equipment and the Receiver to accurately troubleshoot. • Avoid using HDMI keystones.
B-500-RX-230-IR Installation Manual 7. Installation Instructions AC Power B-500-MTRX-230-4x4 ALL IR OUT LINK LINK LINK LINK IR IN Cat 5e/6 HDBaseT HDTV HDMI B-500-RX-230-IR *Can also be used with other HDBaseT transmitters. Follow these steps to install the receiver: 1. Turn off all equipment to be connected. Do not connect power to the B-500-RX-230-IR until all other connections are made. 2.
B-500-RX-230-IR Installation Manual 8. IR Pass-Through This section outlines the connections, optional adapters, and operation of IR pass-through on the B-500-MTRX-230 HDBaseT Receiver. Integration with the B-500-MTRX-230 matrix switcher is detailed. Refer to the documentation included with any transmitter used for specific instructions to integrate IR pass-through. 8.1. Port Pinouts 8.1.1. IR Receiver Port (3.
B-500-RX-230-IR Installation Manual 8.2. IR Installation IR pass-through can be used in two ways, to control displays from the transmitting location (via commands from an automation system), or to control sources and the matrix using IR remotes in the rooms where displays are located. Commands may be passed in both directions at once if necessary.
B-500-RX-230-IR Installation Manual 9 . Specifications TECHNICAL HDMI Compliance HDMI 3D HDCP Compliance Yes Video Bandwidth 10.2 Gbps Resolution HDMI over UTP Transmission Cat5e/ Cat6 Cat6a 1080i / 720p 24-bit color 200ft 230ft Full HD 1080P 24-bit color 200ft 230ft Full HD 1080P 36-bit deep color 200ft 230ft Input TMDS Signal 1.
10. Warranty 2 year 2-Year Limited Warranty This Binary™ Product has a Two-Year Limited Warranty. This warranty includes parts and labor repairs on all components found to be defective in material or workmanship under normal conditions of use. This warranty shall not apply to products which have been abused, modified or disassembled.
