Sit-Stand Workstation Wall Mount Dual Monitor WALLSTS2 *actual product may vary from photos FR: Guide de l’utilisateur - fr.startech.com DE: Bedienungsanleitung - de.startech.com ES: Guía del usuario - es.startech.com NL: Gebruiksaanwijzing - nl.startech.com PT: Guia do usuário - pt.startech.com IT: Guida per l’uso - it.startech.com JP: 取扱説明書 - jp.startech.com For the most up-to-date information, please visit: www.startech.
Warning statements Dichiarazioni di avvertenza Make sure that you assemble this product according to the instructions. Assicurarsi di Assemblare il prodotto secondo le istruzioni. Read the entire manual and make sure that you understand the instructions before you start to assemble and use this product. Leggere l’intero manuale e assicurarsi di aver compreso tutte le istruzioni prima di iniziare ad assemblare e a utilizzare questo prodotto. Never operate this product if parts are missing or damaged.
Advertencias de uso Asegúrese de ensamblar este producto según las instrucciones. Lea todo el manual y asegúrese de haber comprendido bien las instrucciones antes de proceder con el ensamblaje y el uso de este producto. Nunca opere o ponga en funcionamiento este producto si faltan piezas o hay daños en las mismas. El uso de este producto es solo para interiores y no debe utilizarse en exteriores. Cuando ensamble este producto, no apriete los tornillos más de lo debido.
Table of Contents Warnings....................................................................................................................................................... i Product dimensions................................................................................1 Product diagram.....................................................................................3 Technical specifications.........................................................................4 Package contents..............
Counterbalance the weight of the workstation.............................................................................. 38 Adjust the swivel effort of the monitor arm..................................................................................... 39 Extend the keyboard tray........................................................................................................................ 40 Clean the keyboard tray.........................................................................
Product dimensions 794 mm (31.2 in.) 203 mm (8 in.) 333 mm (13.1 in.) 395 mm (15.5 in.) 1194 mm ( 47 in.) 79 mm (3.1 in.) 16 mm (0.6 in.) 50 mm (2 in.) 100 mm (3.9 in.) 75 mm (2.9 in.) 75 mm (2.9 in.) Instruction manual 1 100 mm (3.9 in.) 4.5 mm (0.2 in.) 160 mm (6.3 in.) 124 mm (4.9 in.) 7 mm (0.3 in.) 104 mm (4.1 in.) 210 mm (8.3 in.) 13 mm (0.5 in.
672 mm (26.4 in.) Max 715 mm (28.1 in.) Max 600 mm (23.6 in.) 956 mm (37.6 in.) 926 mm (36.4 in.) 50.5 mm (2 in.) Instruction manual 2 436 mm (17.2 in.) 124 mm (4.9 in.) 410 to 589 mm (16 to 23.2 in.
449 mm (17.7 in.) (0.3 in. to 8.5 in.) 8 mm to 217 mm (0.3 in. to 8.5 in.) 668 mm (26.3 in.) 64 mm (2.5 in.) 44 mm (1.7 in.) Product diagram Crossbar Crossbar VESA monitor mount VESA monitor mount Column Monitor arm Wall plate Keyboard tray Instruction manual 3 255 mm (2.2 in.) 213 mm (8.4 in.) 207 mm (8.1 in.
Technical specifications Type of measurement Measurement 75 x 75 mm 100 x 100 mm VESA 0° to 30° Tilt (monitor) 0° to +90° Tilt (keyboard) 360° Pivot (monitor) +/-90° Swivel (monitor arm) Instruction manual 4
Type of measurement Measurement +/-15° Swivel (monitor) 24 in. or less Supported monitor size LB kg 4.4 to 17.6 lb. (2 to 8 kg) Supported weight (monitors) LB kg 5.5 lb. (2.
Package contents 1 2 Monitor arm Keyboard tray Qty: One Qty: One 3 4 Column VESA monitor mounts Qty: One Qty: Two 5 Instruction manual 6 Wall plate Adhesive strip Qty: One Qty: One 6
7 8 Socket driver 6mm hex key Qty: One Qty: One 9 10 M6x10 mm screws M8x20 mm screw Qty: Five Qty: One 11 Instruction manual 12 Metal washer Plastic washer Qty: One Qty: One 7
14 Mounting screws Concrete anchors Qty: Four Qty: Four 15 16 5 mm hex key M6x12mm screws Qty: One Qty: Four 17 Instruction manual 18 M4x10 screws Crossbar washers Qty: Eight Qty: Two 8
19 20 Knobs Wrench Qty: Two Qty: One 21 22 Crossbars Crossbar mount Qty: Two Qty: One 23 User manual Qty: One Instruction manual 9
Requirements • Monitors that are compatible with one of the VESA mounting hole patterns that WALLSTS2 supports • Pencil or pen to mark the wall • Phillips type screwdriver • ¹/₄ inch drive ratchet Requirements are subject to change. For the latest requirements, please visit www.StarTech.com/WALLSTS2.
Assembly Attach the wall plate to the wall Warning! Wall structures vary, and it is important to make sure that the type of structure and mounting hardware that you are using will properly support the mounted equipment. Failure to do so may result in personal injury and/or equipment damage. The wall should be capable of supporting at least four times the weight of the mounted equipment. Warning! The mounting hardware included with this product might not be adequate for some wall structures.
3. Position the wall plate where you want to hang the WALLSTS2 and make sure that the plate is vertical. 4. Use the four mounting holes in the wall plate as a template and mark the wall. 5. Follow the appropriate steps for the type of wall that you’re attaching the WALLSTS2 to and attach the wall plate to the wall.
Attach the monitor arm to the wall plate 1. Place the monitor arm onto the projection on the wall plate.
2. Place the plastic washer into the joint in the monitor arm. 3. Place the metal washer onto the plastic washer. 4. Insert the M8x20 mm screw through the washers and into the joint in the monitor arm. 5. Use the 6 mm hex key to tighten the screw.
Attach the column to the keyboard tray 1. Position the column with the cutout at the bottom half of the column. 2. Line up the assembly holes on the bottom of the column with the assembly holes between the holders on the keyboard tray.
3. On the underside of the keyboard tray, insert the four M6x12 mm screws through the keyboard tray and into the column. (figure 6) 4. Use the 5 mm hex key to tighten the screws in place.
Attach the column to the monitor arm 1. Insert one of the M6x10 mm screws into the top hole in the plate on the back of the column. (figure 7) Note: Do not tighten the M6x10 mm screw and make sure that you leave between 4 and 5 mm of space between the plate and the screw.
2. Hook the M6x10 mm screw attached to the column into the key-shaped hole at the top of the plate on the monitor arm.
3. Insert the M6x10 mm screws into the lower two holes on the plate on the monitor arm. (figure 9) 4. Use the 5 mm hex key to tighten all three of the screws.
Attach the crossbars to the column 1. Hook the crossbar mount onto the plate on the column.
2. Insert two M6x10 mm screws through the holes under the crossbar mount and into the plate on the column. 3. Use the 5 mm hex key to tighten the screws in place.
4. Slide the crossbars onto the crossbar mount so that the flat sides of the crossbars are against the column.
5. If the crossbars are loose, use the wrench to tighten the bolts in each of the crossbars.
Attach the VESA monitor mounts to the crossbars 1. Insert the rectangular projection on the back of one of the VESA monitor mounts into the slot at the front of one of the crossbars. 2. At the back of the crossbars, insert one of the knobs through one of the crossbar washers and into the back of the VESA monitor mount. 3. Turn the knob clockwise to tighten it. 4. Repeat steps 1 to 3 to attach the other knobs to the other crossbar.
Attach the monitors to the crossbars Warning! Attaching a monitor is a two-person job. Do not attempt to complete this task by yourself. WALLSTS2 is a designed to be used with two monitors that weigh the same. If you attach monitors that are different weights to the WALLSTS2, you do so at your own risk. Use the 100x100 VESA mounting hole pattern to attach the monitors 1. Insert two of the M4x10 mm screws into the mounting holes that are located closest to the top of one of the monitors.
2. Carefully slide the M4x10 mm screws into the top slots of one of the VESA monitor mounts attached to one of the crossbars.
3. Insert two of the M4x10 mm screws into the mounting holes in the bottom two holes in the VESA monitor mount and into the monitor. 4. Use a Phillips type screwdriver to tighten all four of the screws. 5. Repeat steps 1 to 4 to attach the second monitor to the other VESA monitor mount.
Use the 75x75 VESA mounting hole pattern to attach the monitors 1. Insert two of the M4x10 mm screws into the mounting holes that are located closest to the top of one of the monitors. (figure 18) Note: Do not tighten the M4x10 mm screws, and make sure that you leave between 3 and 4 mm of space between the screws and the monitor.
2. Carefully hang the M4x10 mm screws onto the keyhole-shaped holes in one of the VESA monitor mounts attached to one of the crossbars. 3. Insert two of the M4x10 mm screws into the mounting holes in the bottom of the VESA monitor mount and into the monitor. 4. Use a Phillips type screwdriver to tighten all four of the screws. (figure 19) 5. Repeat steps 1 to 4 to attach the second monitor to the other VESA monitor mount.
6. Slide the covers onto the wall plate.
Attach the adhesive strip 1. If necessary, cut the adhesive strip to fit the length of your keyboard. 2. Separate the two sides of the adhesive strip. 3. Remove the backing from one half of the adhesive strip and stick it to the back of your keyboard. 4. Remove the backing from the other half of the adhesive strip and stick it to the surface of the keyboard tray so that it lines up with the strip that you attached to your keyboard.
Route cables 1. Run your cable along the column and through the slot at the bottom of the column. 2. At the top of the cable cover, squeeze the tabs and slide the cable cover up to unhook the tabs at the bottom of the cable cover from the slots in the monitor arm, and lift the cable cover off of the monitor arm. Caution! Be careful not to snap off the tabs from the cable cover when you remove it. 3. Run the cable along the inside of the cable cover. (figure 22) 4.
Remove monitors from the WALLSTS2 Warning: Stored energy hazard! The column contains a lift mechanism that could move up quickly when you remove the monitors from the product. Before you remove the monitors, move the monitors to the highest position. Failure to do so could result in injury or property damage. Warning! Removing a monitor is a two-person job. Do not attempt to complete this task by yourself. 1. Move the monitors to the highest position it can go. (figure 23) 2.
Adjusting the WALLSTS2 Adjust the height of the monitors Caution! When you adjust the monitors, make sure that you move both monitors at the same time. • To adjust the height of the monitors, grasp the bottoms of both monitors and move them up or down.
Adjust the tilt angle of the monitor 1. If necessary, swivel the monitors so that you can access the two screws in the sides of each of the VESA monitor mounts. 2. Use the 5 mm hex key to loosen the two screws in the side of the VESA monitor mount that you want to adjust. 3. Tilt the monitor so that it’s at the angle that you want it at. 4. Use the 5 mm hex key to tighten the two screws in the side of the VESA monitor mount. (figure 25) 5.
Adjust the tilt angle of the keyboard tray • Pull up or push down on the keyboard tray to adjust it from 0 to 90°.
Counterbalance the weight of the monitors The WALLSTS2 features a one-touch height adjustment design that enables you to easily raise or lower your monitors. To use the one-touch height adjustment feature, you need to counterbalance the weight of your monitors. • If the monitors don’t stay in position when you move them or it’s difficult to raise or lower them, use the 5 mm hex key and turn the screw in the top of the column to the right or the left.
Counterbalance the weight of the workstation The WALLSTS2 features a one-touch height adjustment design that enables you to easily raise or lower the entire workstation, including the keyboard tray. To use the one-touch height adjustment feature, you need to counterbalance the weight of the workstation. Stored energy hazard! This product contains a lift mechanism that could move up quickly when you remove the mounted equipment. Before you remove the equipment, move the workstation to the highest position.
Adjust the swivel effort of the monitor arm • To increase or decrease the swivel effort of the monitor arm, use the 6 mm hex key to turn the screw in the plate on the back of the column to the right or left. (figure 29) Caution! When you loosen the screw, make sure that you don’t remove the screw from the joint. If you remove the screw, the column will fall off of the monitor arm and could result in damage to your equipment or injury.
Extend the keyboard tray You can adjust the keyboard tray so that it extends to the left or right. • Pull the extension to the left or right.
Clean the keyboard tray You can remove the extension and the plastic cover from the wrist rest to clean them. 1. To remove the plastic cover from the wrist rest, carefully peel it off of the keyboard tray. (figure 31) 2. To remove the keyboard tray extension, pull the extension all of the way out. On the underside of the keyboard tray, insert a blunt pin into one of the two holes, depress the clip, and pull the extension out of the keyboard tray. (figure 32) 3.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols PHILLIPS® is a registered trademark of Phillips Screw Company in the United States or other countries. This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.
Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise. StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you find the parts that connect your solutions. We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website.
