Mobile TV Cart/Stand - up to 100” User Manual SKU#: STNDMTV100 For the latest information and specifications visit www.startech.
Compliance Statements Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.
Safety Statements Safety Measures • Product installation and/or mounting should be completed by a certified professional as per the local safety and building code guidelines. Mesures de sécurité • L’installation et/ou le montage du produit doit être réalisé par un professionnel certifié et dans le respect des normes locales et du code de construction local.
Warning Statements • Assemble this product according to the instructions. • Read the entire manual and ensure the instructions are fully understood before assembling and/or using this product. • Do not exceed the weight capacity of this product. Overloading this product might result in injury or property damage. • Weight capacity of the multimedia shelf: 5 kg (11 lb.) • Weight capacity of the camera shelf: 5 kg (11 lb.) • Weight capacity of the TV mount: 100 kg (220 lb.
• Det krävs två personer för att montera produkten. Försök inte montera produkten och installera utrustning utan hjälp. • Innan du lägger till utrustning på produkten, se till att produkten är korrekt monterad, installerad och att produkten klarar av vikten på utrustningen som du lägger till. • Se till att all utrustning är korrekt installerad innan du börjar justera produkten. • Flytta inte vagnen över kablar eller ojämna ytor. • Innan du börjar flytta på vagnen, se till att hjulen är upplåsta.
• 本製品で定められた最大積載重量を超えないようにして下さい。最大積載 重量をオーバーした場合、怪我をする恐れや器物破損の恐れがあります。 • マルチメディア棚の総耐荷重:5kg • カメラ棚の総耐荷重:5kg • TVマウンタの総耐荷重:100kg • 本製品に小さなお子様が乗って遊ばないようにして下さい。お子様が使用 する際には、適切な監視を怠らないようにして下さい。 • 本製品は、室内での使用を想定しています。戸外では使用しないで下さい。 • 本製品を組み立てる際、ネジを締めすぎないようにして下さい。ネジを締め ているうちに手応えを感じたら、締めるのを止めてください。 • 本製品は、二人がかりでの組み立てを想定しています。手助けなしに単独で 組み立てと設置を行わないで下さい。 • 本製品に装置を積載する前に、組み立てと設置が適切に行われたか確認し て下さい。 また、積載する装置の重量に本製品が対応しているか確認して 下さい。 • 転倒注意！モニタが一番高い位置にある状態でカートを動かさないで下さ い。 また、モニタを押してカートを動かすのはやめて下さい。 • コードやケーブルの上、 または凹凸のある床面
• Prima di aggiungere altre apparecchiature al prodotto, assicurarsi di averlo assemblato e installato correttamente e che sia in grado di sostenere il peso dell’apparecchiatura in questione. • Assicurarsi di aver installato correttamente tutte le apparecchiature prima di procedere alla regolazione del prodotto. • Non far passare il carrello sopra corde, cavi o superfici irregolari. • Prima di procedere allo spostamento del carrello, verificare di aver sbloccato le rotelle.
• Não exceda a capacidade de peso deste produto. Sobrecarregar este produto pode resultar em ferimentos ou danos de propriedade. • Capacidade de carga de la bandeja multimídia: 5 kg • Capacidade de carga de la bandeja de câmera: 5 kg • Capacidade de carga de suporte para TV: 100 kg • Não deixar as crianças trepar neste produto ou utilizar este produto sem a devida supervisão. • Este produto destina-se apenas a uma utilização no interior e não deve ser utilizado no exterior.
• Antes de instalar equipos en este producto, asegúrese de haberlo ensamblado correctamente, a fin de que pueda soportar el peso del equipo que vaya a instalar. • Asegúrese de que ha instalado todo el equipo correctamente antes de efectuar ajustes de este producto. • No desplace el carrito encima de cables o superficies desniveladas. • Antes de empezar a mover el carrito, asegúrese de haber desbloqueado las ruedas. Antes de empezar a mover el carrito, asegúrese de haber desbloqueado las ruedas.
Table of Contents Compliance Statements.........................................................................i Safety Statements...................................................................................ii Warning Statements...............................................................................iii Product Diagram.....................................................................................1 Front View..................................................................................
Product Diagram Front View Camera Shelf Connecting Plate Left TV Mounting Bracket Right TV Mounting Bracket Universal Plate Left Column Right Column Casters To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Back View Media Shelf Support Bar Base Casters To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Product Dimensions Front View To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Product Information Package Contents Base Casters Universal Plate Handles Qty: 1 Qty: 4 Qty: 1 Qty: 2 Left Column Right Column Qty: 1 Qty: 1 Left TV Mounting Bracket Right TV Mounting Bracket Top Covers Qty: 2 Qty: 1 Qty: 1 Media Shelf Connecting Plate Camera Shelf Qty: 1 Qty: 1 Qty: 1 To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
M6 x 25 mm Screws M4 x 6 mm Screws Qty: 4 Qty: 3 M6 x 25 mm Hex Head Screws M6 x 14 mm Screws M8 x 25 mm Hex Head Screws Qty: 2 Qty: 6 Qty: 8 Hex Key Wrench Qty: 1 Qty: 1 M5 x 14 mm Round Head Screws Support Bar Knobs Qty: 1 Qty: 2 M4 x 6 mm Round Head Screws Qty: 2 M6 x 25 mm Button Head Screws Qty: 4 Qty: 2 5
M6 x 14 mm Round Head Screws M6 x 30 mm Round Head Screws M8 x 30 mm Round Head Screws M8 x 50 mm Round Head Screws Qty: 4 Qty: 4 Qty: 4 Qty: 4 Square Washers Small Spacers Large Spacers User Manual Qty: 4 Qty: 8 Qty: 8 Qty: 1 Requirements For the latest requirements, please visit www.startech.com/STNDMTV100 • TV x 1 • (Optional) Web Camera x 1 • (Optional) Media Device (e.g.
Technical Specifications Type of Measurement Measurement Screen Size 60” - 100” Weight Capacity TV -- Up to 220 lb. (100 kg) Media Shelf -- Up to 11 lb. (5 kg) Camera Shelf -- Up to 11 lb. (5 kg) VESA Compatible 400 x 400 600 x 400 800 x 400 800 x 600 900 x 600 1000 x 600 To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Tilt Range +5° ~ -10° Height Adjustment 47.2 - 65” (1220-1650 mm) Cable Management Yes To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Installation Attach the Casters Casters Wrench Nut Figure 1 1. Flip the Base upside down and place it onto a clean and flat surface. (Figure 1) Note: Cover hard floors with a soft cloth to prevent scratching. 2. Insert each of the four Casters into the holes, located in the bottom of the Base and tighten, using the Wrench. 3. Flip the Base upright so that the Casters are making contact with the surface. 4.
Attach the Columns to the Base Inner Left Column Hex Key Outer Left Column Figure 2 1. Determine the desired mounting height for the TV. 2. Hold the inner and outer Left Column in one hand and loosen the two Hex Screws on the side of the Left Column, using the Hex Key. (Figure 2) Notes: Two People may be required to complete this step. Do not release the grip on the inner and outer portions of the Left Column while the Hex Screws are loose. 3. Extend the Left Column to the desired mounting height.
Plastic Handle Columns Figure 3 Base 6. Engage the Brake on each one of the four Casters before proceeding to step 7. (Figure 3) 7. Slide the Left and Right Columns into their respective locations in the Base. Note: The Cable Management Holes in the Columns must be facing the front of the assembly. 8. Slide one Plastic Handle over the Left Column. Ensure the grip loop portion of the Plastic Handle is facing the back of the Base.
Base M8 x 25 mm Hex Head Screws Hex Key Figure 4 10. Tilt the entire Assembly onto its side to gain access to the bottom of the Base. (Figure 4) Note: It is recommended that Two People complete this step and any subsequent steps that involve tilting or moving the Mobile TV Cart. 11. Insert four M8 x 25 mm Hex Head Screws through the Base and into the Left Column. 12. Tighten all four M8 x 25 mm Hex Head Screws, using the Hex Key. 13. Repeat steps 11-12 for the Right Column. 14.
M6 x 25 mm Screw Figure 5 Attach the Universal Plate M6 x 14 mm Screw Universal Plate Figure 6 1. Place the Universal Plate atop the Left and Right Columns and align the four screw holes in the Universal Plate with the two screw holes in each Column. (Figure 6) 2. Insert four M6 x 14 mm Screws through the Universal Plate and into the Columns (two for each Column). 3. Tighten all four M6 x 14 mm Screws, using a Phillips Head Screwdriver.
Top Cover Column Figure 7 4. Affix one Top Cover over each Column. (Figure 7) Assemble the Media Shelf Knob Media Shelf Figure 8 1. Flip the Media Shelf upside down and place on a clean and flat surface. 2. Place the Support Bar up against the Media Shelf, aligning the holes in the Support Bar with the holes found in the Media Shelf. (Figure 8) To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
3. Hold one of the Knobs up against the outermost hole in the Support Bar and insert one of the M6 x 25 mm Button Head Screws through the square shaped hole in the Media Tray, the Support Bar, and into the Knob. 4. Tighten the Knob. 5. Repeat steps 3-4 to attach the second Knob. 6. Insert two M6 x 14 mm Screws through the innermost circular shaped holes in the Media Tray and into the Support Bar. 7. Tighten the M6 x 14 mm Screws, using a Phillips Head Screwdriver.
1. Hold the Media Shelf Assembly up against/behind the Support Blocks, located on the insides of the Columns. Align the holes in the Support Bar with the holes in the Support Blocks. (Figure 9) 2. Insert one M6 x 25 mm Hex Head Screw through the hole in the Support Block on the Left Column and into the Support Bar. 3. Tighten the M6 x 25 mm Hex Head Screw, using the Hex Key. 4. Repeat steps 2-3 for the Right Column. 5. Determine the desired mounting height for the Media Shelf Assembly. 6.
Attach the TV Mounting Brackets Spacers M-Type Screw Rectangular Washer TV Mounting Bracket TV Figure 10 1. Place the TV on a padded surface, screen side down, so the back of the TV is accessible. (Figure 10) 2. (Optional) Identify and remove the pre-installed VESA Hardware from the back of the TV. Note: Not all TVs will have placeholder VESA Hardware. Only remove the four Screws for the VESA Mount. Do not remove any of the screws from the TV’s structural assembly. 3.
5. Thread the appropriately sized M-Type Screws (e.g. M5 x 14 mm Screws) through the Rectangular Washers, TV Mounting Brackets, (Optional) Spacers, and into the TV. Note: Each Rectangular Washer features two holes. Select the hole that fits the M-Type Screws. 6. Tighten the M-Type Screws, using a Phillips Head Screwdriver, until each Screw sits flush with the surface of the TV Mounting Brackets. Warning! Do not overtighten the M-Type Screws.
2. With two people, lift and hang the TV onto the Universal Plate. Tip: Align the top hooks of the TV Mounting Brackets with the top rails of the Universal Plate. 3. Tighten the 2 Screws in the bottom of the TV Mounting Brackets using the Phillips Head Screwdriver. 4. (Optional - locking) Insert a Padlock through the holes located at the bottom of either TV Mounting Bracket. Assemble the Camera Shelf M4 x 6 mm Round Head Screws Connecting Plate M4 x 6 mm Screws Camera Shelf Figure 12 1.
4. Insert two M4 x 6 mm Round Head Screws through the back of the Camera Shelf and into the back of the Connecting Plate. 5. Tighten the two M4 x 6 mm Round Head Screws, using a Phillips Head Screwdriver. Attach the Camera Shelf Assembly Connecting Plate M6 x 25 mm Screws Figure 13 1. Determine the desired mounting height of the Camera Shelf above the TV. 2.
Cable Management Grommet (removable) Figure 14 1. Route the Cables from the back of the TV into the Grommets located at the top-front of the Columns. (Figure 14) Note: All Grommets are removable. 2. Route the Cables through the Columns. 3. Route the Cables out of the Grommets located at the bottom-front of the Columns and into their respective Power Source and/or Video Source. To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Operation Adjust the Tilt Angle of the TV Mounting Brackets 1. Loosen the two Nuts on the outward facing side of one TV Mounting Bracket, using the Wrench. Note: Do not completely loosen the Nuts. 2. Repeat step 1 for the second TV Mounting Bracket. 3. Tilt the TV to the desired angle. Note: Two People are required for all tilt adjustments. 4. Tighten the four Nuts that were loosened in steps 2-3, using the Wrench.
Warranty Information This product is backed by a five-year warranty. For further information on product warranty terms and conditions, please refer to www.startech.com/warranty. Limitation of Liability In no event shall the liability of StarTech.com Ltd. and StarTech.
Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise. StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you find the parts that connect your solutions. We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website.
