0.2” to 10.5” Secure iPad® Enclosure with Surface Mount *Actual product may vary from photos User Manual SKU: SECTBLTPOS2 For the latest information and specifications visit www.StarTech.
Compliance Statements Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.
Safety Statements Safety Measures • Product installation and/or mounting should be completed by a certified professional as per the local safety and building code guidelines. Mesures de sécurité • L’installation et/ou le montage du produit doit être réalisé par un professionnel certifié et dans le respect des normes locales et du code de construction local.
Warning Statements • Assemble this product according to the instructions. • Read the entire manual and ensure the instructions are fully understood before assembling and/or using this product. • This product is intended for indoor use only and should not be used outdoors. • Do not over-tighten the screws. If any resistance is encountered, stop tightening. • Pinch hazard! Keep your fingers clear from moving components. Varningsmeddelanden • Se till att du monterar produkten i enlighet med instruktionerna.
• 本製品を組み立てる際、ネジを締めすぎないようにして下さい。ネジを締め ているうちに手応えを感じたら、締めるのを止めてください。 • 危険！可動部品に近づかないでください。 Dichiarazioni di avvertenza • Assicurarsi di Assemblare il prodotto secondo le istruzioni. • Leggere l’intero manuale e assicurarsi di aver compreso tutte le istruzioni prima di iniziare ad assemblare e a utilizzare questo prodotto. • Il prodotto è destinato all’uso in ambienti interni. Se ne sconsiglia l’impiego in ambienti esterni. • Durante l’assemblaggio del prodotto, non stringere troppo le viti.
Advertencias de uso • Asegúrese de ensamblar este producto según las instrucciones. • Lea todo el manual y asegúrese de haber comprendido bien las instrucciones antes de proceder con el ensamblaje y el uso de este producto. • El uso de este producto es solo para interiores y no debe utilizarse en exteriores. • Cuando ensamble este producto, no apriete los tornillos más de lo debido. Si al apretar los tornillos siente resistencia, no los apriete más.
Table of Contents Compliance Statements.........................................................................i Safety Statements...................................................................................ii Warning Statements...............................................................................iii Product Diagram.....................................................................................1 Front View..................................................................................
Mounting Option #2 - Tabletop - Rotating....................................................................................... 10 Mounting Option #3 - Wall Mount....................................................................................................... 11 Attach the Tablet Enclosure Assembly to the Angled Bracket................................................... 12 Warranty...................................................................................................
Product Diagram Front View Tablet Enclosure Assembly Lock Angled Bracket To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Product Dimensions Note: All measurements are in millimeters. Front View Rear View Bottom View Edge View To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Side View Product Information Requirements For the latest manuals, product information, technical specifications, and Declarations of Conformance, please visit: www.StarTech.com/SECTBLTPOS2 • Phillips Head Screwdriver • Electric Drill • Pencil To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Package Contents Note: The following images are not to scale. Tablet Enclosure Assembly Angled Bracket Keys Qty: 1 Qty: 2 150 x 10 mm Felt Tape 20 x 15 x 3 mm EVA Pads 45 x 15 x 2 mm EVA Pads 100 x 25 x 20 mm Foam Blocks Qty: 2 Qty: 4 Qty: 2 Qty: 2 100 x 15 x 12 mm Foam Blocks M4 x 8 mm Screws M2.5 Hex Key Rubber Pads Qty: 1 Qty: 4 Qty: 1 200 x 5 mm Felt Tape Qty: 2 To view manuals, Qty: 2 videos, drivers, downloads, Qty: 4 technical drawings, and more visit www.startech.
5 x 20 mm Self Tapping Screws Qty: 3 Small Washers Large Washers User Manual Qty: 3 Qty: 2 Qty: 1 To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Installation Note: Do not overtighten any of the screws. Pinch hazards! Keep hands away from any pinch points created by the mechanical components. Failure to do so may result in serious personal injury. Add the iPad to the Tablet Enclosure Assembly Unlock the Tablet Enclosure Assembly Front Plate Rear Plate Figure 1 1. Insert the Key into the Lock, located on the side of the Tablet Enclosure Assembly, and turn counterclockwise to unlock. (Figure 1) 2. Remove the Front Plate from the Rear Plate.
Add the Felt Tape to the Front Plate Front Plate 150 mm x 10 mm Felt Tape Adhesive Backing 200 mm x 5 mm Felt Tape Figure 2 1. Remove the Adhesive Backing from the 200 x 5 mm Felt Tape (x 2) and affix to the long edges of the inside of the Display Frame, located on the Front Plate. (Figure 2) 2. Remove the Adhesive Backing from the 150 x 10 mm Felt Tape (x 2) and affix to the short edges of the inside of the Display Frame, located on the Front Plate.
2. (Optional) Remove the Adhesive Backing from the 100 x 25 x 20 mm Foam Blocks (x 2) and affix next to the Tabs, towards the center of the Rear Plate. 3. (Optional) Remove the Adhesive Backing from the 100 x 15 x 12 mm Foam Blocks (x 2) and affix along the inside edge on the top and bottom of the Rear Plate. (Figure 4) Insert the iPad into the Tablet Enclosure Assembly Front Plate Charging Cord Rear Plate Figure 5 Figure 6 1.
Mounting the Angled Bracket Rubber Pads Figure 7 • Remove the Adhesive Backing from the Rubber Pads (x 4) and affix to the base of the Angled Bracket. (Figure 7) Mounting Option #1 - Tabletop- Fixed 5 x 20 mm Self Tapping Screws Small Washers Figure 8 1. Place the Angled Bracket in the intended mounting location, on a Tabletop. 2. Mark the location of the Screw Holes (x 3), using a Pencil. 3.
4. Thread the Small Washers (x 3) over the 5 x 20 mm Self Tapping Screws (x 3) to complete the Screw Assemblies. 5. Align the mounting holes, located on the Angled Bracket, with the Pilot Holes, located in the Tabletop. 6. Insert the Screw Assemblies (x 3) through the Angled Bracket and into the Tabletop and tighten, using a Phillips Head Screwdriver. (Figure 8) Mounting Option #2 - Tabletop - Rotating 5 x 20 mm Self Tapping Screw Small Washer Large Washers Figure 9 1.
5. Align the Large Washers (x 2) over the Pilot Hole. (Figure 9) 6. Align the hole, located towards the front of the Angled Bracket, with the hole, located in the Large Washers. 7. Insert the Screw Assembly through the Angled Bracket, the Large Washers, and into the Tabletop and partially tighten, using a Phillips Head Screwdriver. 8. Adjust the tension of the Screw Assembly to adjust the ease of rotation. Mounting Option #3 - Wall Mount Small Washers 5 x 20 mm Self Tapping Screws Figure 10 1.
4. Thread the Small Washers (x 3) over the 5 x 20 mm Self Tapping Screws (x 3) to complete the Screw Assemblies. 5. Align the Angled Bracket with Pilot Holes, located in the Wall. 6. Insert the Screw Assemblies (x 3) through the Angled Bracket and into the Wall and tighten, using a Phillips Head Screwdriver. (Figure 10) Attach the Tablet Enclosure Assembly to the Angled Bracket 1.
Warranty Information This product is backed by a five-year warranty. For further information on product warranty terms and conditions, please refer to www.startech.com/warranty. Limitation of Liability In no event shall the liability of StarTech.com Ltd. and StarTech.
Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise. StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you find the parts that connect your solutions. We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website.
