Universal Projector Wall Mount Actual product may vary from photos User Manual SKU#: PROJWALLMNT For the latest information and specifications visit www.startech.
Compliance Statements Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.
Safety Statements Safety Measures • Product installation and/or mounting should be completed by a certified professional as per the local safety and building code guidelines. Mesures de sécurité • L’installation et/ou le montage du produit doit être réalisé par un professionnel certifié et dans le respect des normes locales et du code de construction local.
Warning Statements • Make sure to assemble this product according to the instructions. Failure to do so might result in personal injury or property damage. • Never use this product if parts are missing or damaged. • The projector wall mount is designed to be installed on a wood stud, solid concrete, or cinder block wall. The wall structure should also be capable of supporting at least four times the weight of the mounted equipment.
den monterade utrustningen. Om du inte gör det kan skada på person och/ eller utrustning uppstå. Väggstrukturen ska kunna klara av minst fyra gånger vikten av den monterade utrustningen. • Monteringsutrustningen som medföljer produkten kanske inte är lämplig för vissa väggstrukturer.
nécessaires pour installer ce produit au mur, contactez un professionnel afin qu’il installe le support mural ou qu’il vous fournisse les instructions de montage spécifiques à votre structure de mur. Waarschuwingen • Zorg dat dit product volgens de instructies in elkaar wordt gezet. Indien dit niet goed gebeurt kan lichamelijk letsel of materiële schade ontstaan. • Gebruik dit product nooit als er onderdelen ontbreken of beschadigd zijn.
注意 • 必ず取扱説明書に従って本製品の組み立てを行って下さい。取り扱いを誤 った場合に、傷害を負う恐れや物的損害が発生する恐れがあります。 • 本製品で使用している部品の一部が紛失していたり損傷している状態で使 用するのは絶対に止めて下さい。 • 壁の構造はお客様の環境ごとに異なります。 ご使用になる壁の構造タイプ と取付け金具が、取り付けモニターを確実に支持することを確認して下さ い。確認を怠った場合、傷害を負う恐れや物的損害が発生する恐れがあり ます。壁の構造が、取り付けるモニター重量の最低4倍まで支持できるだけ の強度を持っていなければなりません。 • 本製品に同梱されている取付け金具は、 ご使用になる壁の構造に対して十 分ではない場合があります。本製品を壁面に取り付ける時、十分な専門知 識が不足していると判断された場合、専門業者に連絡を取って、本製品の取 り付けを行ってもらうか、お客様の壁の構造に適した取り付け方法を教えて もらってから取り付けを行って下さい。 Dichiarazioni di avvertenza • Assemblare il prodotto rispettando le
Table of Contents Compliance Statements.................................................................................... i Safety Statements............................................................................................... ii Warning Statements........................................................................................... iii Product Diagram................................................................................................. 1 Front-Side View..........................
Product Diagram Front-Side View Upper Decorative Cover Projector Pole Pole End Cap Lower Decorative Cover Mounting Arm Covers To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Rear-Side View Adjustment Module Wall Bracket To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Adjustment Knobs 1 2 3 1) Tilt Turn clockwise to adjust the picture down. Turn counterclockwise to adjust the picture up. 2 ) Rotate Turn clockwise to adjust the picture counterclockwise. Turn counterclockwise to adjust the picture clockwise. 3) Swivel Turn clockwise to adjust the picture to the right. Turn counterclockwise to adjust the picture to the left. Note: An Adjustment Screw must be loosened before the Grey Adjustment Knob can be turned.
Product Dimensions Note: All measurements are listed in millimeters. To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Product Information Package Contents Wall Bracket Projector Pole Pole End Cap Upper Decorative Wall Cover Qty: 1 Qty: 1 Qty: 1 Qty: 1 Lower Decorative Wall Cover Adjustment Module Right Adjustment Module Cover Left Adjustment Module Cover Qty: 1 Qty: 1 Qty: 1 Qty: 1 Mounting Arms Mounting Arm Covers Hinge Connector Wall Anchors To view manuals, and more Qty: 4 videos, drivers, downloads, technical drawings,Qty: 1 visit www.startech.
Mounting Screws Washers 10 mm Wrench 5 mm Hex Key Qty: 6 Qty: 4 Qty: 1 Qty: 1 M5 x 24 mm Screws M6 x 8 mm Hex Screws M6 x 10 mm Screws M6 x 25 mm Hex Screw M6 x 24 mm Screws Qty: 4 (Of Each) Qty: 2 Qty: 1 M3 x 24 mm Screws M4 x 24 mm Screws Qty: 4 (Of Each) Nuts User Manual Qty: 4 Qty: 1 6
Requirements • • • • Phillips Head Screwdriver Spirit/Bubble Level Mounting Surface (Optional) Two People for the Installation To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Technical Specifications Type of Measurement Measurement Weight Capacity Up to 33.1 lb. (15 kg) kg Tilt +50 to -50 Swivel +100 to -100 Horizontal Movement +20 mm to -20 mm To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Installation Fasten the Wall Bracket to a Wall Warning! The Universal Projector Wall Mount is designed to be installed on a wood stud, solid concrete, or cinder block wall. The wall structure should be capable of supporting at least four times the weight of the mounted equipment. The Mounting Hardware included with this product may not be adequate for installation on certain wall structures. Contact a construction professional to install the Universal Projector Wall Mount.
2. (Optional, For In-Wall Cable Management) Feed the Power and Video Cables into the Wall. Connect the Power Cable to an available Power Source. Connect the Video Cable to the Video Source Device. 3. Press the Projector Pole into the Wall Mount and hold the Projector Pole in place. Align the four holes in the Projector Pole with the four holes in the Wall Mount. Attach the Projector Pole to the Wall Mount • Thread the four M6 x 8 mm Hex Screws through the Wall Mount and into the Projector Pole.
2. Place the four Mounting Arms onto the Projector, with the tubular portion of the Mounting Arms aligned over the Mounting Holes in the Projector. (Figure 3) Note: The threads of the Variable Position Screws, that are built into the Mounting Arms, should be facing upwards. Figure 3 Mounting Arm Cover Variable Position Screw Mounting Arm Projector 3. Thread the appropriately sized M-Type Screws (e.g. M4 x 24 mm Screws) through the Mounting Arms and into the Projector. 4.
5. Place the Mounting Arm Covers over the Mounting Arms. Attach the Adjustment Module 1. Place the Adjustment Module onto the Mounting Arms. Align the Variable Position Screws with the cutouts in the Adjustment Module. (Figure 4) Note: If the Adjustment Module does not fit onto the Mounting Arms, loosen the M-Type Screws with a Phillips Head Screwdriver and readjust the position of the Mounting Arms. Tighten the M-Type Screws once the correct position has been achieved.
2. Place the four Washers over the Variable Position Screws. 3. Thread the four Nuts onto the Variable Position Screws. Tighten using the 10 mm Wrench. 4. Attach the Right and Left Adjustment Module Covers by sliding the Covers together over the Adjustment Module until the two Covers snap together. (Figure 5) Note: To remove these Adjustment Module Covers, locate the labels that say Open. Apply pressure to one of these labels while pulling the two Covers apart. Repeat for the other side.
2. Thread the two M6 x 10 mm Screws through the Adjustment Module and into the Hinge Connector. Hand tighten the M6 x 10 mm Screws by one rotation. (Figure 6) Note: There must be a 2-3 mm gap between the Adjustment Module and the Hinge Connector in order to complete the following installation steps. Figure 6 Hinge Connector M6 x 10 mm Screw 10 mm Wrench Adjustment Module 3. Slide the Projector Mount Assembly onto the Projector Pole.
4. Tighten the M6 x 10 mm Screws that were threaded through the Adjustment Module and Hinge Connector in Step 2 using the 10 mm Wrench. (Figure 8) Figure 8 M6 x 10 mm Screw 10 mm Wrench 5. Attach the Power and Video Cables to the Projector. (Figure 9) Figure 9 Power and Video Cables To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
6. Insert the Pole End Cap into the Projector Pole until it snaps into place. (Figure 10) Note: Pinch the sides and top of the Pole End Cap during insertion. Figure 10 Projector Pole Pole End Cap 7. Adjust the length of the Projector Pole by pulling apart to lengthen and pushing together to shorten. Tighten the two 5 mm Hex Bolts located underneath, using the 5 mm Hex Key. (Figure 11) To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Figure 11 Projector Pole 5 mm Hex Bolts 5 mm Hex Key Cable Management Ensure the Power and Video Cables have been connected to the Projector. (Optional) For On-Wall Cable Management 2. Determine if the Power and Video Cables will be routed out of the Upper or Lower Decorative Cover. 1. 3. Break away the Plastic Tab on the Decorative Cover that was chosen in Step 2. (Figure 12) To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Figure 12 Plastic Tab Upper Decorative Cover Lower Decorative Cover 4. Slide the Upper and Lower Decorative Covers together, over the Wall Bracket, until the two Covers snap into place. Note: To remove these Decorative Covers, press the sides at the top of the Lower Decorative Cover and pull apart. 5. Connect the Power Cable to an available Power Source. Connect the Video Cable to the Video Source Device. Operation Adjust the Wall Mount Tilt Angle 1. Remove the Upper and Lower Decorative Covers.
2. Loosen the four M6 x 8 mm Hex Screws on the side of the Wall Mount, using the 5 mm Hex Key. 3. Insert the M6 x 25 mm Hex Screw into the hole in the Wall Mount and tighten (angle up) or loosen (angle down), using the 5 mm Hex Key until the desired angle is met. (Figure 13) Figure 13 M6 x 8 mm Hex Screws M6 x 25 mm Hex Screw 4. Tighten the four M6 x 8 mm Hex Screws on the side of the Wall Mount, using the 5 mm Hex Key. 5.
2. Turn the Grey Adjustment Knob in a Clockwise direction to adjust the Projected Image to the right. - or Turn the Grey Adjustment Knob in a Counterclockwise direction to adjust the Projected Image to the left. (Figure 14) Figure 14 3. Tighten the Adjustment Screw, located next to the Grey Adjustment Knob, using the 10 mm Wrench. Adjust the Tilt • • Turn the Yellow Adjustment Knob in a Clockwise direction to adjust the Projected Image down.
Figure 15 Adjust the Rotation • • Turn the Black Adjustment Knob in a Clockwise direction to rotate the Projected Image counterclockwise. - or Turn the Black Adjustment Knob in a Counterclockwise direction to rotate the Projected Image clockwise. (Figure 16) Figure 16 To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Adjust the Horizontal Lateral Position 1. Loosen the two Adjustment Screws located on the top of the Adjustment Module, using the 10 mm Wrench. 2. Slide the Projector Mount Assembly to the left or the right to adjust the Projected Image to the left or right. (Figure 17) Figure 17 Adjustment Screw 10 mm Wrench 3. Tighten the two Adjustment Screws located on the top of the Adjustment Module, using the 10 mm Wrench. To view manuals, videos, drivers, downloads, technical drawings, and more visit www.
Warranty Information This product is backed by a two-year warranty. For further information on product warranty terms and conditions, please refer to www.startech.com/warranty. Limitation of Liability In no event shall the liability of StarTech.com Ltd. and StarTech.
Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise. StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you find the parts that connect your solutions. We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website.