Universal Ceiling Projector Mount Actual product may vary from photos User Manual SKU#: PROJCEILMNT2 For the latest information and specifications visit www.startech.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which this manual applies by the third-party company in question.
Safety Statements Safety Measures • Cables (including power and charging cables) should be placed and routed to avoid creating electric, tripping or safety hazards.
Warning Statements • Do not exceed the weight capacity of this product. Overloading this product might result in injury or property damage. This product can support the following weight: 33.1 lb. (15 kg). • Make sure to assemble this product according to the instructions. Failure to do so might result in personal injury or property damage. • Never operate this product if parts are missing or damaged.
a instalação em parede ou para fornecer instruções de montagem específicas para a sua estrutura de parede. Varningsmeddelanden • Se till att du monterar produkten i enlighet med instruktionerna. Om du inte gör det kan skada på person eller egendom uppstå. • Se till att skärmens vikt inte överstiger produktens viktkapacitet. Om viktkapaciteten överstigs kan skada på person eller utrustning uppstå. Denna produkt har stöd för följande vikter: 15 kg. • Använd aldrig produkten om delar saknas eller är skadade.
experiencia suficiente para fijar este producto a la estructura de la pared correspondiente, póngase en contacto con un profesional de la construcción para instalar el soporte de pared o para que le proporcione las instrucciones específicas de montaje para su estructura de pared. Avertissements • Assemblez ce produit conformément aux instructions. Si vous ne respectez pas ces instructions, vous risquez de vous blesser ou d’endommager l’équipement.
het type wandstructuur en de montagemiddelen die u gebruikt de gemonteerde apparatuur goed ondersteunen. Indien u dit niet doet kan lichamelijk letsel en/of schade aan de apparatuur ontstaan. De wandstructuur moet voldoende zijn om ten minste vier keer het gewicht van de gemonteerde apparatuur te ondersteunen. • De bij dit product geleverde montagemiddelen kunnen niet geschikt zijn voor sommige wandstructuren.
までのモニター重量に対応しています。 • 本製品で使用している部品の一部が紛失していたり損傷している状態で使 用するのは絶対に止めて下さい。 • 壁の構造はお客様の環境ごとに異なります。 ご使用になる壁の構造タイプ と取付け金具が、取り付けモニターを確実に支持することを確認して下さ い。確認を怠った場合、傷害を負う恐れや物的損害が発生する恐れがあり ます。壁の構造が、取り付けるモニター重量の最低４倍まで支持できるだけ の強度を持っていなければなりません。 • 本製品に同梱されている取付け金具は、 ご使用になる壁の構造に対して十 分ではない場合があります。本製品を壁面に取り付ける時、十分な専門知 識が不足していると判断された場合、専門業者に連絡を取って、本製品の取 り付けを行ってもらうか、お客様の壁の構造に適した取り付け方法を教えて もらってから取り付けを行って下さい。 Dichiarazioni di avvertenza • Assemblare il prodotto rispettando le istruzioni.
Table of Contents Safety Statements...................................................................................2 Warning Statements...............................................................................3 Product Diagram.....................................................................................9 Product Dimensions...............................................................................10 Flush Installation.........................................................................
Product Diagram 1 2 3 5 4 6 1 Ceiling Bracket 2 Upper Pole 3 Lower Pole 4 Projector Plate 5 Lock Switch 6 Mounting Arms (x 4) To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Product Dimensions Flush Installation Extended Installation Min. To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Extended Installation Max. To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Product Rotation Mounting Pattern To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Product Information Package Contents Ceiling Bracket Projector Plate Qty: 1 Qty: 1 Projector Plate Cover Upper Pole Qty: 1 Qty: 1 To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Lower Pole Ball-Joint Mechanism Qty: 1 Qty: 1 Mounting Arms Mounting Arm Covers Qty: 4 Qty: 4 M6 x 12 mm Screws 5 mm Hex Key Qty: 7 Qty: 1 To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Wall Anchors Mounting Screws Qty: 4 Qty: 4 Washers Nuts Qty: 4 Qty: 6 M3 x 24 mm Screws M4 x 24 mm Screws Qty: 4 Qty: 4 To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
M5 x 24 mm Screws M6 x 24 mm Screws Qty: 4 Qty: 4 M6 x 65 mm Screws Qty: 2 To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Technical Specifications LB kg 33.1 lb. (15 kg) Total Weight - 250 to + 250 Tilt 3600 Swivel To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Requirements • • • • • 8 mm Wrench x 1 10 mm Wrench x 1 Socket Wrench x 1 8 mm Socket x 1 Phillips Head Screwdriver x 1 To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Mounting the Projector Mount (using Extensions) Warning! Product mounting should be completed by a certified professional as per the local safety and building code guidelines. Ceiling structures vary, and it is important to make sure that the type of structure and mounting hardware that you are using will properly support the mounted equipment. Failure to do so may result in personal injury and/or equipment damage. 1.
3. When the Ceiling Plate is installed in a ceiling, slide both pieces of the Ceiling Plate Cover back over-top of the Ceiling Plate, snaping them together. 4. Align the Mounting Arms with the Mounting Holes on the top of the Projector. 5. Select the appropriate Installation Screws (M3 x 24 mm, M4 x 24mm, M5 x 24 mm, or M6 x 24 mm). 6. Insert the selected Installation Screws (x 4), through the Mounting Holes in the Mounting Arms and into the Mounting Holes on the Projector.
8. Place the Mounting Arm Covers over-top of the Mounting Arms, aligning them so that the Screw on the Mounting Arm is protruding through the Slot in the Mounting Arm Cover. Installing the Mounting Arm Covers 9. Align the Screws on the Mounting Arms with the appropriate Cut-Outs on the Projector Plate. 10. Insert the Screws on the Mounting Arms through the Cut- Outs in the Projector Plate. 11.
Installing the Projector Plate 12. Place the Projector Plate Cover over the Projector Plate. 13. Align the Protrusions on the bottom of the Ball-Joint Mechanism with the Slots in the top of the Projector Plate Cover. Installing the Ball-Joint Mechanism 14. Insert the Protrusions into the Slots and rotate the Ball- Joint Mechanism clockwise until it locks into place. To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Rotating the Ball-Joint Mechanism 15. Insert one of the M6 x 12 mm Screws into the Lock Screw Hole on the Projector Plate Cover and tighten it using the 5 mm Hex Key (included). Inserting an M6 x 12 mm Screw To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
16. Route the Cables connected to the Projector (e.g. Power Cable, etc.), though the bottom end of the Lower Pole with Cable Notch and out through the top. Routing the Projector Power Cable 17. Attach the bottom of the Lower Pole (with Cable Notch) to the top of the Ball-Joint Mechanism. Make sure that the Mounting Holes on the Lower Pole are aligned with the Mounting Holes on the Ball-Joint Mechanism.
Attaching the Lower Pole to the Ball-Joint Mechanism 20. Feed the Projector Cables through the Upper Pole and slide the Upper Pole (with the two screw holes facing down) down over-top of the Lower Pole. 21. Insert the M6 x 65 mm Screws ( x2) through the Screw Holes on the Upper Pole and the Adustment Holes Lower Poles (at the appropriate height) and into a Nut on the opposite side. 22.
Attaching the Upper and Lower Poles 23. While supporting the weight of the Projector and Projector Mount, slide the Upper Pole onto the Ceiling Plate. Making sure that you align the Cable Notch in the Upper Pole with the Cable Notch in the Ceiling Bracket. Note: Make sure that all Cables are aligned with the Ceiling Bracket so that they come out the side of the Cable Notch. To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Attaching the Upper Pole to the Ceiling Mount 24. Align the Mounting Holes on the Upper Pole with the Mounting Holes on the Ceiling Bracket. 25. Insert a M6 x 12 mm Screw (x 3) through the Mounting Holes (x 3) in the Upper Pole and into the Mounting Holes ( x 3) on the Ceiling Bracket. 26. Using the 5 mm Hex Key, tighten the M6 x 12 mm Screws. To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Securing the Upper Pole Mounting the Projector Mount (Flush) Warning! Product mounting should be completed by a certified professional as per the local safety and building code guidelines. Ceiling structures vary, and it is important to make sure that the type of structure and mounting hardware that you are using will properly support the mounted equipment. Failure to do so may result in personal injury and/or equipment damage. 1.
Removing the Ceiling Plate Cover 2. Mount the Ceiling Bracket to the ceiling using the Mounting Screw (x 4) included or the appropriate hardware. 3. When the Ceiling Plate is installed in a ceiling, slide both piecies of the Ceiling Plate Cover back over-top of the Ceiling Plate, snapping them together. 4. Align the Mounting Arms with the Mounting Holes on the top of the Projector. 5. Select the appropriate Installation Screws (M3 x 24 mm, M4 x 24mm, M5 x 24 mm, or M6 x 24 mm). 6.
Installing the Mounting Arms 7. Using a Phillips Head Screwdriver, tighten the Installation Screws. Be careful not to over-tighten. To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
8. Place the Mounting Arm Covers over-top of the Mounting Arms, aligning them so that the Screw on the Mounting Arm is protruding through the Slot in the Mounting Arm Cover. Installing the Mounting Arm Covers 9. Align the Screws on the Mounting Arms with the appropriate Cut Outs on the Projector Plate. 10. Insert the Screws on the Mounting Arms through the Cut- Outs in the Projector Plate. 11.
Installing the Projector Plate 12. Place the Projector Plate Cover over the Projector Plate. 13. Align the Protrusions on the bottom of the Ball-Joint Mechanism with the Slots in the top of the Projector Plate Cover. Installing the Ball-Joint Mechanism 14. Insert the Protrusions into the Slots and rotate the Ball- Joint Mechanism clockwise until it locks into place. To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Rotating the Ball-Joint Mechanism 15. Insert one of the M6 x 12 mm Screws into the Lock Screw Hole on the Projector Plate Cover and tighten it using the 5 mm Hex Key (included). Inserting an M6 x 12 mm Screw To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
16. Align the Mounting Holes on the Ball-Joint Mechanism with the Mounting Holes on the Ceiling Plate. 17. Insert an M6 x 12 mm Screw (x 2) through the Mounting Holes (x 2) in the Ball-Joint Mechanism and into the Mounting Holes ( x 2) on the Ceiling Plate. 18. Using the 5 mm Hex Key, tighten the M6 x 12 mm Screws. Installing the Ball-Joint Mechanism to the Ceiling Plate To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Adjusting the Projector Mount 1. Move the Lock Switch on the Ball-Joint Mechanism into the Unlock position. Unlocking the Projector Mount 2. Rotate the Projector Mount in order to adjust the direction the Projector is pointing. Rotate the Projector Mount 3. Tilt the Projector Mount up or down to adjust the tilt of the Projector Mount. To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Adjusting the Tilt 4. When you have the Projector Mount in the desired position, move the Lock Switch on the Ball-Joint Mechanism back into the locked position, securing the Projector in place. Adjusting the Torque 1. Using the 5 mm Hex Key, remove the M6 x 12 mm Screws from the Ball-Joint Mechanism from either the Lower Pole or the Ceiling Bracket, depending on your installation method. 2.
Adjusting the Torque 3. When you have adjusted the torque accordingly, replace the Ball-Joint Mechanism. Using the 5 mm Hex Key tighten the M6 x 12 mm Screws, securing the Ball-Joint Mechanism back in place. To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Warranty Information This product is backed by a two-year warranty. For further information on product warranty terms and conditions, please refer to www.startech.com/warranty. Limitation of Liability In no event shall the liability of StarTech.com Ltd. and StarTech.
Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise. StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you find the parts that connect your solutions. We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website.
