User Manual

ManualsBrandsStartech ManualsHardwareStarTech.com PCI Serial Parallel Combo Card with Dual Serial RS232 Ports (DB9) & 1x Parallel LPT Port (DB25), PCI Combo Adapter Card, PCI Expansion Card Controller, PCI to Printer Card PCI Serial & Parallel Card - serial adapter - PCIe - RS-232 x 2

Quick-Start Guide

To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.

Manual Revision: February 26, 2021

Product Diagram (PCI2S1P2)

Front View

Port Function

1 Parallel Connector • Connect to the Parallel Pins on the PCI Card

Low-Prole Bracket

(Parallel)

• See Installing the Low-Prole Bracket(s)

3 Parallel Port

• Connect a Parallel Peripheral Device

• DB-25 Parallel (Female)

Low-Prole Brackets

(Serial)

• See Installing the Low-Prole Bracket(s)

5 Serial Ports

• Connect Serial Peripheral Devices

• DB-9 Parallel (Male)

6 PCI Connector

• Connect the PCI Card to the PCI Slot in the

Computer

Package Contents

• PCI Serial Parallel Combo Card x 1

• Full-Prole Bracket (Installed) x 1

• Low-Prole Brackets (for Serial Ports) x 2

• Low-Prole Bracket (for Parallel Port) x 1

• Quick-Start Guide x 1

2S1P PCI Serial Parallel Combo Card with 16C550 UART

Requirements

For the latest requirements, please visit:

www.startech.com/PCI2S1P2.

• Computer with an available PCI slot (x4/8/16)

• Needle-nose Pliers or 3/16 Nut Driver

Hardware Installation

Warning: PCI Cards can be damaged by static electricity. Make sure that the

Installer is properly grounded before they open the Computer Case or touch the PCI

Card. The Installer should wear an Anti-Static Strap when installing any computer

component. If an Anti-Static Strap is not available, discharge any built-up static

electricity by touching a large Grounded Metal Surface for several seconds. Only

handle the PCI Card by its edges and do not touch the gold connectors.

Installing the Low-Prole Bracket(s)

By default the Full-Prole Bracket is attached to the Serial/Parallel Port(s).

Depending on the system conguration it may be necessary to remove the Full-

Prole Bracket(s) to replace with the Low-Prole Bracket(s) (included).

1. Remove the Hexagonal Standos from both sides of each Port, using a 3/16 Nut

Driver or a pair of Needle-nose Pliers.

2. Remove the Full-Prole Bracket(s) and replace with the Low-Prole Bracket(s).

3. Install the Hexagonal Standos removed in step 1. Thread the Hexagonal

Standos onto each Threaded Post and tighten, using a 3/16 Nut Driver or a pair

of Needle-nose Pliers.

Installing the Card

1. Turn o the Computer and any Peripheral Devices that are connected

(e.g. printers, external hard drives, etc.).

2. Unplug the Power Cable from the rear of the Computer and disconnect any

Peripheral Devices that are connected.

3. Remove the Cover from the Computer Case.

Note: Consult the documentation that came with the Computer for details about

how to do this safely.

4. Locate an open PCI Slot and remove the corresponding Metal Cover Plate from the

rear of the Computer Case. In most instances, the Metal Cover Plate is attached

to the rear of the Computer Case with a single Screw. Save this Screw for the next

step.

Summary of content (2 pages)

PAGE 1
Quick-Start Guide 2S1P PCI Serial Parallel Combo Card with 16C550 UART Product Diagram (PCI2S1P2) Requirements Front View For the latest requirements, please visit: www.startech.com/PCI2S1P2.
PAGE 2
5. Gently insert the PCI Card into the open PCI Slot and fasten the Bracket to the rear of the Computer Case, using the Screw from step 4. 6. Locate a second open PCI Slot and remove the corresponding Metal Cover Plate from the rear of the Computer Case. In most instances, the Metal Cover Plate is attached to the rear of the Computer Case with a single Screw. Save this Screw for the next step. 7. Fasten the Bracket (Parallel) to the rear of the Computer Case, using the Screw from step 6.