Mobile Cart with Display Rotation - Integrated Cable Management Actual product may vary from photos User Manual SKU#: MBLTVSTNDEC For the latest information and specifications visit www.startech.
Compliance Statements Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.
Safety Statements Safety Measures • Product installation and/or mounting should be completed by a certified professional as per the local safety and building code guidelines. Mesures de sécurité • L’installation et/ou le montage du produit doit être réalisé par un professionnel certifié et dans le respect des normes locales et du code de construction local.
Warning Statements • Assemble this product according to the instructions. • Read the entire manual and ensure the instructions are fully understood before assembling and/or using this product. • Do not exceed the weight capacity of this product. Overloading this product might result in injury or property damage. • Weight capacity of the multimedia shelf: 5 kg (11 lb.) • Weight capacity of the TV mount: 70 kg (154 lb.
• Innan du lägger till utrustning på produkten, se till att produkten är korrekt monterad, installerad och att produkten klarar av vikten på utrustningen som du lägger till. • Se till att all utrustning är korrekt installerad innan du börjar justera produkten. • Flytta inte vagnen över kablar eller ojämna ytor. • Innan du börjar flytta på vagnen, se till att hjulen är upplåsta. Waarschuwingen • Zorg dat u dit product volgens de instructies in elkaar zet.
• TVマウンタの総耐荷重:100kg • 本製品に小さなお子様が乗って遊ばないようにして下さい。お子様が使用 する際には、適切な監視を怠らないようにして下さい。 • 本製品は、室内での使用を想定しています。戸外では使用しないで下さい。 • 本製品を組み立てる際、ネジを締めすぎないようにして下さい。ネジを締め ているうちに手応えを感じたら、締めるのを止めてください。 • 本製品は、二人がかりでの組み立てを想定しています。手助けなしに単独で 組み立てと設置を行わないで下さい。 • 本製品に装置を積載する前に、組み立てと設置が適切に行われたか確認し て下さい。 また、積載する装置の重量に本製品が対応しているか確認して 下さい。 • 転倒注意！モニタが一番高い位置にある状態でカートを動かさないで下さ い。 また、モニタを押してカートを動かすのはやめて下さい。 • コードやケーブルの上、 または凹凸のある床面でカートを移動させないで 下さい。 Dichiarazioni di avvertenza • Assicurarsi di Assemblare il prodotto secondo le istruzi
• Non far passare il carrello sopra corde, cavi o superfici irregolari. • Prima di procedere allo spostamento del carrello, verificare di aver sbloccato le rotelle. Avertissements • Assemblez ce produit conformément aux instructions. • Lisez tout le manuel et assurez-vous que vous comprenez les instructions avant de commencer à assembler et utiliser ce produit. • Ne dépassez pas la capacité pondérale du produit. Une surcharge du produit peut entraîner des blessures ou des dommages matériels.
• Este produto destina-se apenas a uma utilização no interior e não deve ser utilizado no exterior. • Quando montar este produto, não aperte demasiado os parafusos. Se encontrar resistência enquanto aperta os parafusos, pare de apertar. • Montar este produto é uma tarefa para duas pessoas. Não tentar montar este produto e instalar o equipamento sem assistência.
• No desplace el carrito encima de cables o superficies desniveladas. • Antes de empezar a mover el carrito, asegúrese de haber desbloqueado las ruedas. Antes de empezar a mover el carrito, asegúrese de haber desbloqueado las ruedas. Warnhinweise • Beachten Sie bei der Montage dieses Produkts die Montageanweisungen. • Bevor Sie dieses Produkt montieren und verwenden, lesen Sie das gesamte Handbuch und vergewissern Sie sich, dass Sie die Anweisungen verstanden haben.
Table of Contents Compliance Statements.........................................................................i Safety Statements...................................................................................ii Warning Statements...............................................................................iii Product Diagram.....................................................................................1 Front View..................................................................................
Rotate the TV............................................................................................................................................... 19 Cable Management................................................................................................................................... 20 Attach the Rear Cover............................................................................................................................... 21 Operation.......................................
Product Diagram Front View VESA Extension Arms (L) VESA Extension Arms (R) Upper Columns Base Columns Casters To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Back View VESA Mounting Plate VESA Extension Arms Rear Bracket Cover Equipment Shelf Shelf Brackets Base To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Product Dimensions Front View To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Product Information Package Contents Base Casters Base Columns Upper Columns Qty: 1 Qty: 4 Qty: 2 Qty: 2 Equipment Shelf Shelf Brackets Qty: 1 Qty: 2 Front Bracket Cover VESA Mounting Plate Qty: 1 Qty: 1 Rear Bracket Cover VESA Extension Arms (L) VESA Extension Arms (R) Cable Covers Qty: 4 Qty: 2 videos, drivers, downloads, To view manuals, and more Qty: 2 technical drawings,Qty: 2 visit www.startech.
M8 x 20 mm Screws M6 x 8 mm Screws M6 x 12 mm Screws M6 x 18 mm Screw Qty: 8 Qty: 8 Qty: 16 Qty: 1 M8 x 8 mm Screws Cable Clip Holders Cable Clips M6 Wrench Qty: 8 Qty: 5 Qty: 5 Qty: 1 M10 Wrench 4 mm Hex Key 5 mm Hex Key Qty: 1 Qty: 1 Qty: 1 M5 x 14 mm Round Head Screws Qty: 4 5
M6 x 14 mm Screws M6 x 30 mm Screws M8 x 30 mm Screws M8 x 50 mm Screws Qty: 4 Qty: 4 Qty: 4 Qty: 4 Rectangular Washers Small Spacers Large Spacers User Manual Qty: 8 Qty: 8 Qty: 1 Qty: 4 Requirements For the latest requirements, please visit www.startech.com/MBLTVSTNDEC • TV x 1 • Phillips Head Screwdriver x 1 • Scissors x 1 • Needle-Nose Pliers x 1 • (Optional) Media Device (e.g.
Technical Specifications Type of Measurement Measurement Screen Size 37” - 70” Weight Capacity TV -- Up to 154 lb. (70 kg) Media Shelf -- Up to 11 lb. (5 kg) VESA Compatible 200 x 200 mm 300 x 300 mm 350 x 350 mm 400 x 200 mm 400 x 400 mm 600 x 200 mm 600 x 400 mm To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Tilt Range 0° or +5° Rotation 0° ~ +90° Cable Management Yes To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Installation Note: Do not overtighten any of the screws. Attach the Casters Casters Base Brake Figure 1 Figure 2 1. Flip the Base upside down and place it onto a clean and flat surface. (Figure 1) Note: Cover hard floors with a soft cloth to prevent scratching. 2. Insert the four Casters into the holes, located in the bottom of the Base and tighten, using the 10 mm Wrench. 3. Flip the Base upright. 4. Lock the Casters by pressing down on the Brake, located on top of each of the four Casters.
Attach the Base Columns to the Base Cable Management Slots Base Columns M8 x 20 mm Screws Base Figure 3 1. 5 mm Hex Key Insert the Base Columns into the Base. Press firmly to ensure the Base Columns have been fully inserted into the Base. (Figure 3) Note: Ensure the Cable Management Slots on each of the Base Columns are facing the rear of the Mobile Cart and are at the same height. 2.
Attach the Upper Columns to the Base Columns Upper Columns M6 x 8 mm Screws 4 mm Hex Key Cable Management Slot Base Columns Shelf Brackets Figure 4 1. Slide one Shelf Bracket onto each Base Column. Slide the Shelf Brackets past the Screw Holes, located in the Base Columns. (Figure 4) 2. Insert the narrow end of the Upper Columns into the tops of the Base Columns. Note: Ensure the Cable Management Slots in the Upper Columns are facing inwards. 3.
Install the Front Cover and Equipment Shelf M6 x 12 mm Screws Front Cover Equipment Shelf M6 x 12 mm Screws M8 x 20 mm Screws 5 mm Hex Key Figure 5 1. Align the holes in the sides of the Front Cover and the four lowest inward facing holes on the Upper Columns. The Directional Arrow on the Front Cover should be pointing up and should only be visible from the rear of the Mobile Cart. (Figure 5.1) 2.
3. Angle the Equipment Shelf and slide the notch from one side against one of the Upper Columns and the Shelf Bracket. Tilt the other notch down onto the other Shelf Bracket. The large overhanging portion should be facing the rear of the Mobile Cart. (Figure 5.2) 4. Insert two M6 x 12 mm Screws through the bottoms of both Shelf Brackets and into the Equipment Shelf and tighten, using a Phillips Head Screwdriver. (Figure 5.3) 5.
1. Place the TV on a padded surface, screen side down, so the back of the TV is accessible. (Figure 7) 2. (Optional) Identify and remove the pre-installed VESA Hardware from the back of the TV. Note: Not all TVs will have placeholder VESA Hardware. Only remove the four Screws for the VESA Mount. Do not remove any of the screws from the TV’s structural assembly. 3.
Note: Each Rectangular Washer features two holes. Select the hole that fits the M-Type Screws. 10. Tighten the M-Type Screws, using a Phillips Head Screwdriver, until each Screw sits flush with the surface of the TV Mounting Brackets. Warning! Do not overtighten the M-Type Screws. If any unexpected resistance is encountered while fastening these Screws, immediately stop and attempt to use a different length of M-Type Screw. Attach the VESA Mounting Plate to a TV VESA Mounting Plate TV Figure 7 1.
Note: Not all TVs will have placeholder VESA Hardware. Only remove the four Screws for the VESA Mount. Do not remove any of the screws from the TV’s structural assembly. 3. (Optional -- for TVs with recessed VESA Mounting Holes, for TVs with uneven rear geometry, or to adjust the engagement depth of the provided Screws) Add the necessary number of Small and/or Large Spacers between the VESA Mounting Plate and TV. 4.
Mounting the TV VESA Mounting Plate M8 x 20 mm Screws Figure 8 1. Insert two M8 x 20 mm Screws into two uppermost inwardfacing holes in the Upper Columns and tighten until 10 mm of the M8 x 20 mm Screw threads are exposed, using the 5 mm Hex Key. (Figure 8) 2. (Completed this step with Two People) Lift the TV, tilt the top backwards slightly, and hook the top of the VESA Mounting Plate onto the top two M8 x 20 mm Screws, installed in step 1.
Set the Tilt of the TV M8 x 20 mm Screws 5 mm Hex Key Figure 9 1. Fully hand-tighten the top M8 x 20 mm Screw on each Upper Column. (Figure 9) 2. Loosen the top two M8 x 20 mm Screws on each Upper Column by a quarter turn, using the 5 mm Hex Key. Warning! Do not over-loosen or remove the M8 x 20 mm Screws. 3. Tilt the TV to the desired setting and align the two lower holes in the VESA Mounting Plate with the holes in the Upper Columns. 4.
Rotate the TV Nuts 10 mm Wrench Figure 10 M6 x 18 mm Screw Figure 11 1. (Optional - to adjust the torque required to rotate the TV) a. (Increase the torque required to rotate the TV) tighten the Nuts on the VESA Mounting Plate, using the M10 Wrench. (Figure 10) b. (Decrease the torque required to rotate the TV) loosen the Nuts on the VESA Mounting Plate, using the M10 Wrench. To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
2. Rotate the TV to landscape view or portrait view. 3. Insert the M6 x 18 mm Screw into the hole located just above (for landscape viewing) or to the side of (for portrait viewing) the bolts in the VESA Mounting Plate and tighten, using an appropriately sized Phillips Head Screwdriver.
1. Route the Cables through the Cable Management Slots in the Columns. 2. Peel the plastic backing off the Cable Clip Holders and stick them to the desired locations within the VESA Mounting Plate. (Figure 12) Note: Excess slack can be coiled and secured using two Cable Clips. (Figure 13) 3. Thread the Cable Clips through the Cable Clip Holders. 4. Secure the Cables with the Cable Clips and tighten. 5.
1. Place the Rear Cover over the VESA Mounting Plate and Front Bracket Cover. Align the holes in the top of the Rear Cover with the holes in the top of the VESA Mounting Plate. Align the holes in the bottom of the Rear Cover with the holes in the bottom of the Front Bracket Cover. (Figure 16) 2. Insert four M6 x 12 mm Screws into the holes aligned in step 1 and tighten, using an appropriately sized Phillips Head Screwdriver. Operation Adjust the Tilt of the TV 1.
7. Tighten the top two M8 x 20 mm Screws, using the 5 mm Hex Key. Move the Mobile Cart Assembly Warning! Never attempt to move the Mobile Cart Assembly with one person. A minimum of two people are required to move the Mobile TV Stand Assembly. 1. Unplug all the Cables connecting the Mobile Cart to any Stationary Object (e.g. the wall, a media device, etc.). 2. Disengage the Brakes on the Casters. 3. Grip the TV and the Upper Columns and slowly move the Mobile Cart Assembly, using two people.
Warranty Information This product is backed by a five-year warranty. For further information on product warranty terms and conditions, please refer to www.startech.com/warranty. Limitation of Liability In no event shall the liability of StarTech.com Ltd. and StarTech.
Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise. StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you find the parts that connect your solutions. We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website.
