HDMI® Audio/Video Over IP Extender Kit ST12MHDLAN *actual product may vary from photos DE: Bedienungsanleitung - de.startech.com FR: Guide de l'utilisateur - fr.startech.com ES: Guía del usuario - es.startech.com IT: Guida per l'uso - it.startech.com NL: Gebruiksaanwijzing - nl.startech.com PT: Guia do usuário - pt.startech.com For the most up-to-date information, please visit: www.startech.
FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Table of Contents Introduction.............................................................................................1 Packaging Contents.................................................................................................................................. 1 System Requirements............................................................................................................................... 1 Preparing Your Site....................................................................
Introduction The ST12MHDLAN HDMI® Over IP Extender kit lets you extend an HDMI® audio and video signal over a Gigabit LAN network. The kit includes both the extender and receiver for a complete all-in-one solution, and offers a highly scalable installation when used with additional ST12MHDLANRX receiver units (sold separately). The ST12MHDLANRX receivers can be connected to the same network to output the HDMI® signal to over 100 additional displays.
Transmitter Unit 6 2 3 1 1. F2 (Not Active) 1 2 3 4 1. Power Jack 5 2. F1 (Used during factory default setting) 2. Network Status LED 3. Dip Rotary Switch (Used to pair Transmitter to Receiver) 4. LAN Port (RJ-45 Connector) 3. Reset Button 5. Video In 6. Link OK POWER LED Receiver Unit (Additional Receiver units sold seperately ST12MHDLANRX) 6 1 2 3 1 3 2 4 1. F2 (Used during EDID Copy procedure) 1. Power Jack 2. F1 (Used during factory default setting) 3. Reset Button 2.
Preparing Your Site NOTE: The ST12MHDLAN HDMI® extender kit can use a Gigabit LAN Network to extend the signal. Most Gigabit Network portals have a cable length restriction of 330 ft. (100m). Refer to the manufacturer of the equipment to determine the length restriction and ensure the Transmitter Unit, and Receiver Unit(s) are all within the restricted range of the nearest network portal. Ensure the Transmitter Unit, and Receiver Unit(s) are all situated near an available AC electrical outlet. 1.
Hardware Installation Using Gigabit LAN Network 1. Install Transmitter Unit a) Position the Transmitter Unit near the video source (i.e. Computer, Blu-ray Player). b) Connect an HDMI cable from the video source device (i.e. computer, Blu-ray Player) to the “Video In” port on the Transmitter Unit. c) Connect the provided Transmitter Unit power supply. 2. Install Receiver Unit(s) a) Position the Receiver Unit(s) near the video display (i.e. television, projector).
(Optional) Point to Point Hardware Installation without Gigabit LAN Network NOTE: While range is reduced to a maximum of 330 feet (100 Meters) the ST12MHDLAN HDMI® extender kit also allows for extending the signal without a Gigabit LAN Network by connecting the Transmitter directly to the Receiver using CAT5e/6 cabling. This also eliminates the ability to add additional Receivers. 1. Install Transmitter Unit d) Position the Transmitter Unit near the video source (i.e. Computer, Blu-ray Player).
Hardware Reset Procedure NOTE: If video signal does not appear on the display a hardware reset can be performed on the Transmitter Unit, or individual Receiver Units. 1. Press the reset button on the device using a pin point tool, such as a ballpoint pen or a bent paper clip. EDID Copy EDID allows the video source to output the most ideal signal to the video display. The “EDID Copy” function on the ST12MHDLANRX ensures that EDID is still active through the Ethernet extender.
Specifications Maximum Digital Resolutions 1920x1200 @60Hz Supported Resolutions 1920 x 1200 (1080p) Wide Screen Supported Yes Audio Specifications Stereo Sound Interface HDMI® Cabling Cat 5e UTP or better Audio Yes Rack-Mountable Yes Industry Standards HDMI® HDCP Daisy-Chain Yes Transmitter Connectors 1x HDMI® (19 pin) 1x RJ-45 Receiver Connectors 1x HDMI® (19 pin) 1x RJ-45 Power Adapter Input Voltage 100~240V Power Adapter Input Current 0.
Technical Support StarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and access our comprehensive selection of online tools, documentation, and downloads. For the latest drivers/software, please visit www.startech.com/downloads Warranty Information This product is backed by a two year warranty. In addition, StarTech.
Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise. StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you find the parts that connect your solutions. We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website.
