Flat-Screen TV Ceiling Mount - Long Pole - Full Motion FPCEILPTBLP *actual product may vary from photos FR: Guide de l’utilisateur - fr.startech.com DE: Bedienungsanleitung - de.startech.com ES: Guía del usuario - es.startech.com NL: Gebruiksaanwijzing - nl.startech.com PT: Guia do usuário - pt.startech.com IT: Guida per l’uso - it.startech.com For the latest information, technical specifications, and support for this product, please visit www.StarTech.com/FPCEILPTBLP.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols PHILLIPS® is a registered trademark of Phillips Screw Company in the United States or other countries. This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.
Warning statements Mensagens de aviso Make sure to assemble this product according to the instructions. Failure to do so might result in personal injury or property damage. Certifique-se de que monta este produto de acordo com as instruções. O incumprimento pode resultar em ferimentos pessoais ou danos de propriedade. Make sure that the weight of the monitor doesn’t exceed the weight capacity of this product.
Table of Contents Warnings....................................................................................................................................................... i Introduction.............................................................................................1 Product diagram......................................................................................................................................... 1 Product dimensions...................................................
Introduction Product diagram Ceiling mount and pole Middle pole Lower pole Horizontal bracket Vertical bracket Vertical bracket Instruction manual 1
Product dimensions 200 mm -60° +60° min 2500 mm to max 3000 mm min 2718 mm to max 3218 mm 48 mm 48 mm -3° +3° 360° min 200 mm to max 600 mm 680 mm Instruction manual 2 435 mm min 200 mm to max 400 mm 40 mm +0° -25°
Technical specifications Type of measurement Measurement VESA mounting hole pattern 200x200 300x300 400x200 400x400 600x400 Rated load 50 kg (110 lb.) kg Tilt +00 to -250 Screen size Between 813 mm and 1905 mm (32 in. and 75 in.
Package contents 1 2 Ceiling mount and pole Middle pole Qty: One Qty: One 4 3 Lower pole TV mount Qty: One Qty: One 5 6 Vertical brackets Horizontal bracket Qty: Two Qty: One Instruction manual 4
8 7 M8x55 mm screws M8x60 mm screws Qty: Two Qty: Two 9 10 Nuts Wrench Qty: Four Qty: One 12 11 Instruction manual Hex key Mounting template Qty: One Qty: One 5
13 14 M5x14 mm screws M6x14 mm screws Qty: Four Qty: Four 15 16 M6x30 mm screws M8x30 mm screws Qty: Four Qty: Four 17 18 M8x50 mm screws Rectangular washers Qty: Four Qty: Four Instruction manual 6
19 20 Small spacers Large spacers Qty: Eight Qty: Eight 22 21 Screws Concrete anchors Qty: Four Qty: Four 23 24 Circular washers Instruction manual Qty: Four Qty: One Instruction manual 7
Requirements • A display or TV that is compatible with one of the VESA mounting hole patterns that FPCEILPTBLP supports • A Phillips screwdriver Requirements are subject to change. For the latest requirements, please visit www.StarTech.com/FPCEILPTBLP. Installation Warning! Make sure that the weight of the TV does not exceed the weight capacity of this product. If you exceed the weight capacity, you might experience personal injury or damage to the product.
figure 1 Mounting template 2. Follow the appropriate steps for the type of ceiling that you’re attaching the mount to and attach the ceiling mount and pole to the ceiling. 3. To adjust the vertical position of the pole, use the wrench and the hex key to adjust the nut at the side of the mounting base.
Attach the middle pole to the ceiling mount and pole 1. Place one end of the TV cable through the top hole in the ceiling mount and pole. 2. Run the cable through the ceiling mount and pole, the middle pole, and out the bottom.
3. Line up the holes on the middle pole with the holes on the ceiling mount and pole. 4. Insert the two M8x60 mm screws through the holes in the middle pole and the ceiling mount and pole. 5. Attach two nuts to the screws, and use the wrench and the hex key to tighten the nuts in place.
6. Slide the display mount down the lower pole. (figure 5) figure 5 Display mount Lower pole 7. Run the cable through the lower pole and out the bottom.
8. Line up the holes on the lower pole with the holes on the middle pole, and insert the two M8x55 mm screws through the poles. 9. Attach two nuts to the screws, and use the wrench and the hex key to tighten the nuts in place.
Attach the horizontal bracket 1. Use a wrench to remove the retainer nut from the back of the horizontal bracket. (figure 8) figure 8 Nuts Wrench Horizontal bracket Retainer nut 2. Loosen the two nuts at the back of the horizontal bracket. 3. Attach the horizontal bracket onto the TV mount at the end of the lower pole. 4. Reattach the retainer nut that you removed in step 1 and use a wrench to tighten the nut in place. (figure 9) 5. Tighten the two nuts that you loosened in step 2.
Prepare the vertical brackets 1. Use a screwdriver to remove the screw from the mounting hardware on each of the two vertical brackets. 2. Set the screws aside; you will need to use them when you hang the TV. 3. Flip down the smaller piece of the mounting hardware.
Mount a TV with a flush mounting surface To accommodate different TV designs, the FPCEILPTBLP comes with five sets of screws of different lengths and diameters, and two sizes of spacers. 1. To select the combination of mounting hardware that you need to use to attach the vertical brackets to the TV, complete the following: • Determine the depth of the mounting holes on the TV. • Determine the diameter of the mounting holes on the TV.
Mount a TV with a recessed mounting surface To accommodate different TV designs, the FPCEILPTBLP comes with five sets of screws of different lengths and diameters, and two sizes of spacers. 1. To select the combination of mounting hardware that you need to use to attach the vertical brackets to the TV, complete the following: • Determine the depth of the mounting holes on the TV. • Determine the diameter of the mounting holes on the TV.
2. Line up the vertical brackets with the mounting holes on the back of the TV. 3. Place the rectangular washers over the vertical brackets. 4. Insert the M6x30 mm screws, M8x30 mm screws, or M8x50 screws through the washers, vertical brackets, spacers, and into the back of the monitor. 5. Use a Phillips screwdriver to tighten the screws. (figure 12) Warning! Do not over-tighten the screws. If you encounter resistance while you’re tightening the screws, stop tightening.
Attach the TV to the horizontal bracket Warning! Make sure that the weight of the TV doesn’t exceed the weight capacity of this product. If you exceed the weight capacity, you might experience personal injury or damage to the product. This product can support the following weight: Up to 50 kg (110 lb.) Warning! Attaching the monitors is a two-person job. Do not attempt to complete this task by yourself. 1.
2. Flip up the mounting hardware and reinsert the screws that you removed from the mounting hardware on each of the vertical brackets. (figure 14) 3. Use a Phillips screwdriver to tighten the screws in place.
4. Make any necessary adjustments to the angle of the TV.
Technical support StarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and access our comprehensive selection of online tools, documentation, and downloads. For the latest drivers/software, please visit www.startech.com/downloads Warranty information This product is backed by a five-year warranty. StarTech.
Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise. StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you find the parts that connect your solutions. We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website.
