Single-Monitor Arm - One-Touch Height Adjustment - Heavy Duty Actual product may vary from photos User Manual SKU#: ARMPIVOTHD & ARMPIVOTHDB For the latest information and specifications visit www.startech.
Compliance Statements FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
service by StarTech.com, or an endorsement of the product(s) to which this manual applies by the third-party company in question. Regardless of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby acknowledges that all trademarks, registered trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the property of their respective holders.
Safety Statements Safety Measures • Wiring terminations should not be made with the product and/or electric lines under power. • Product installation and/or mounting should be completed by a certified professional as per the local safety and building code guidelines. • Cables (including power and charging cables) should be placed and routed to avoid creating electric, tripping or safety hazards.
Warning Statements Make sure to assemble this product according to the instructions. Failure to do so might result in personal injury or property damage. Make sure that the weight of the monitor doesn’t exceed the weight capacity of this product. If you exceed the weight capacity, you might experience personal injury or damage to the equipment. This product can support the following weight: 19.8 lb. (9 kg). Never operate this product if parts are missing or damaged.
Gewicht geeignet: 9 kg. Das Produkt darf nicht bedient werden, wenn Teile fehlen oder beschädigt sind. Wenn sich Komponentenkabel in beweglichen Teilen verfangen, kann dies zu Verletzungen von Personen oder Schäden an Geräten führen. Dichiarazioni di avvertenza Assemblare il prodotto rispettando le istruzioni. Il mancato rispetto delle istruzioni potrebbe causare danni a persone o proprietà. Verificare che il peso del monitor non superi la capacità di supporto del prodotto.
movimiento se pueden producir lesiones personales o daños en el equipo. Waarschuwingen Zorg dat dit product volgens de instructies in elkaar wordt gezet. Indien dit niet goed gebeurt kan lichamelijk letsel of materiële schade ontstaan. Zorg dat het gewicht van het scherm de maximale capaciteit van dit product niet overschrijdt. Als u de gewichtscapaciteit overschrijdt, kan persoonlijk letsel of schade aan de apparatuur ontstaan. Dit product ondersteunt het volgende gewicht: 9 kg.
Table of Contents Compliance Statements.........................................................................1 Safety Statements...................................................................................3 Warning Statements...............................................................................4 Technical Specification...........................................................................8 Package Contents.................................................................................
Product Diagram Spring Arm Lower Cable Cover Hex Key Holder Upper Cable Cover VESA Monitor Mount Desk Clamp To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Product Dimensions 115 mm 80 mm 75 mm min 255 mm to max 315 mm 100 mm 210 mm 75 mm 100 mm min 10 mm to max 85 mm 100 mm min 170 mm to max 505 mm 115 mm To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Technical Specification Type of Measurement Measurement 75x75 100x100 VESA Mounting Hole Pattern Up to 9 kg (19.8 lb.) kg Weight Capacity +900 to -900 Tilt Max 813 mm (32 in.) Screen Size To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
1800 Rotate 1800 Swivel To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Package Contents 1 2 Spring Arm VESA Monitor Mount Qty: One Qty: One 4 3 Grommet Base Plate Grommet Knob Qty: One Qty: One 5 6 Grommet Screw Grommet Plate Qty: One Qty: One To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
8 7 Rubber Pads Desk Clamp Qty: Two Qty: One 9 10 L Bracket Clamp Screws Qty: One 11 Qty: Five 12 Hex Key Holder 4 mm Hex Key Qty: One Qty: One To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
13 14 5 mm Hex Key 6 mm Hex Key Qty: One Qty: One 15 16 M5x12 mm Screws M4x12 mm Thumbscrews Qty: Four Qty: Four 18 17 Washers Spacers Qty: Four Qty: Four 19 User Manual Qty: One To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Requirements Requirements are subject to change. For the latest requirements, please visit www.StarTech.com/ARMPIVOTHD. • Monitor/Display that is compatible with a VESA mount • Phillips Screwdriver Assembly You can use either the desk clamp or grommet mount to attach the Arm Mount to your mounting surface. Use the Desk Clamp to Attach the Arm Mount Warning! Make sure that the weight of the monitor doesn’t exceed the weight capacity of this product, up to 9 kg (19.8 lb.).
3. Use the 4 mm Hex Key (12) to tighten the Clamp Screws. (Figure 1) Spring Arm Base L Bracket Clamp Screw Figure 1 4 mm Hex Key To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
4. Remove the backing from the two Rubber Pads (7) and affix the Rubber Pads to the tops of two of the Clamp Screws on the underside of the L Bracket and Spring Arm. (Figure 2) Rubber Pad Clamp Screw L Bracket Spring Arm Base Figure 2 5. Depending on the thickness of your mounting surface, do one of the following: • If your mounting surface is between 10 and 55 mm (0.4 and 2.2 in) a. Position the Desk Clamp (8) so that the holes on the Desk Clamp line up with the top two holes in the L Bracket. b.
c. Use the 4 mm Hex Key to tighten the Clamp Screws. (Figure 3) 4 mm Hex Key 10 to 55 mm Clamp Screw Desk Clamp L Bracket Figure 3 To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
If your mounting surface is between 50 and 85 mm (1.9 and 3.3 in) a. Position the Desk Clamp (8) so that the holes on the Desk Clamp line up with the bottom two holes in the L Bracket. b. Insert two of the clamp screws through the L Bracket and into the Desk Clamp. c. Use the 4 mm Hex Key to tighten the Clamp Screws. (Figure 4) • Clamp Screw 50 to 85 mm 4 mm Hex Key Desk Clamp L Bracket Figure 4 To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
6. Snap the Hex Key Holder (11) onto the L Bracket. (Figure 5) Hex Key Holder L Bracket Figure 5 7. Turn the knob on the Desk Clamp counterclockwise until you reach the thickness of the mounting surface that the Arm Mount is attached to. 8. Slide the Desk Clamp over the edge of the mounting surface. To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
9. Turn the knob clockwise to tighten the Desk Clamp. (Figure 6) Desk Clamp Figure 6 To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Use the Grommet Mount to Attach the Arm Mount Warning! Make sure that the weight of the monitor doesn’t exceed the weight capacity of this product. If you exceed the weight capacity, you might experience personal injury or damage to the product. This product can support the following weight: Up to 9 kg (19.8 lb.). 1. Insert the Grommet Screw (5) through the Grommet Base Plate (3).
2. Line up the three holes on the top of the Grommet Base Plate with the holes on the bottom of the Spring Arm (1). 3. Insert three of the Clamp Screws (10) through the Grommet Base Plate and into the bottom of the Spring Arm. 4. Use the 4 mm Hex Key (12) to tighten the Clamp Screws. (Figure 8) Spring Arm Grommet Base Plate Clamp Screw Grommet Screw 4 mm Hex Key Figure 8 To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
5. Remove the backing from the two Rubber Pads (7) and affix the Rubber Pads to the tops of two of the Clamp Screws on the underside of the Spring Arm. (Figure 9) Grommet Screw Rubber Pad Spring Arm Figure 9 To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
6. Place the assembled spring arm and grommet screw over the grommet hole in your mounting surface. 7. On the underside of the mounting surface, thread the Grommet Plate (6) through the Grommet Screw so that the Grommet Plate is flush against the mounting surface. 8. Screw the Grommet Knob (4) onto the Grommet Screw and turn the Grommet Knob clockwise to tighten it flush against the Grommet Plate.
Attach a Monitor Warning! Attaching a monitor is a two-person job. Do not attempt to complete this task by yourself. To accommodate different monitor designs, the Arm Mount comes with two sets of screws that are different lengths and diameters, and a set of spacers. To select the appropriate screws for the type of monitor that you’re using, complete the following: • Determine whether the back of the monitor is flush or inset. • Determine the depth of the mounting holes on the monitor.
3. Insert the four M4x12 mm Thumbscrews (15) or the four M5x12 mm Screws (16) through the Washers, the VESA Monitor Mount, and into the back of the monitor. (figure 11) Top of Monitor VESA Monitor Mount M4 Thumbscrew or M5 Screw Washer Figure 11 Spacer To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
4. Use a Phillips screwdriver to tighten the screws. Warning! Do not over-tighten the screws. If you encounter resistance while you’re tightening the screws, stop tightening. Failure to do so could result in damage to the monitor. 5. Pull the tab on the Spring Arm (1), and slide the VESA Monitor Mount and monitor into the mount on the Spring Arm. (Figure 12) VESA Monitor Mount Spring Arm Figure 12 To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Adjust the Spring Arm You need to adjust the spring arm in two places. 1. To increase or decrease the tension in the Spring Arm (1), hold down the Spring Arm so that it is straight, and use the 6 mm Hex Key (14) to turn the screw in the joint of the Spring Arm counterclockwise or clockwise. (Figure 13) 6 mm Hex Key Figure 13 To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
2. To change the angle that the monitor is tilted at, use the 6 mm Hex Key to turn the screw in the side of the mount counterclockwise. When the screw is loose, position the monitor at the angle that works best for you. Use the 6 mm Hex Key to turn the screw clockwise to tighten it. (Figure 14) 6 mm Hex Key Figure 14 To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Tip! If you used the Desk Mount to mount the Arm Mount, when you’re done adjusting the Arm Mount, you can store the hex keys in the Hex Key Holder (11) on the side of the L Bracket (9). (Figure 15) 6 mm Hex Key 4 mm Hex Key Hex Key Holder Figure 15 To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Routing the Cables 1. On the bottom portion of the Spring Arm (1), slide the Cable Cover up and away from the Spring Arm. (Figure 16) Spring Arm Cable Cover Figure 16 To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
2. On the upper portion of the Spring Arm, pull the ends of the Cable Cover away from the Spring Arm, and remove the Cable Cover from the Spring Arm. (Figure 17) Spring Arm Cable Cover Figure 17 To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
3. Run the cables along the inside of the Cable Cover that you removed from the upper portion of the Spring Arm. 4. To reattach the Cable Cover, pull out the ends of the Cable Cover and insert the Tabs on the inside of the Cable Cover into the holes on the Spring Arm. (Figure 18) Hole Tab Spring Arm Cable Cover Hole Tab Figure 18 To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
5. Run the cables along the inside of the Cable Cover that you removed from the bottom portion of the Spring Arm. (Figure 19) Cable Cable Cover Figure 19 To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
6. Place the Cable Cover slightly higher than the cavity in the lower part of the Spring Arm, and slide the Cable Cover down so that the Hooks on the Cable Cover slide into the Clips in the Spring Arm. (Figure 20) Spring Arm Hook Cable Cover Hook Figure 20 To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Adjust the Position of the Arm Mount You can adjust the Arm Mount in the following ways: 180° +90° 180° -90° 360° 270° To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Technical Support StarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and access our comprehensive selection of online tools, documentation, and downloads. For the latest drivers/software, please visit www.startech.com/downloads Warranty Information This product is backed by a five-year warranty. StarTech.
Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise. StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you find the parts that connect your solutions. We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website.
