Single-Monitor Arm - One-Touch Height Adjustment - Heavy Duty ARMPIVOTHD *actual product may vary from photos FR: Guide de l’utilisateur - fr.startech.com DE: Bedienungsanleitung - de.startech.com ES: Guía del usuario - es.startech.com NL: Gebruiksaanwijzing - nl.startech.com PT: Guia do usuário - pt.startech.com IT: Guida per l’uso - it.startech.com For the latest information, technical specifications, and support for this product, please visit www.StarTech.com/ARMPIVOTHD.
FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Warning statements Waarschuwingen Make sure to assemble this product according to the instructions. Failure to do so might result in personal injury or property damage. Zorg dat dit product volgens de instructies in elkaar wordt gezet. Indien dit niet goed gebeurt kan lichamelijk letsel of materiële schade ontstaan. Make sure that the weight of the monitor doesn’t exceed the weight capacity of this product.
Table of Contents Warnings....................................................................................................................................................... i Introduction.............................................................................................1 Product diagram......................................................................................................................................... 1 Product dimensions...................................................
Introduction The ARMPIVOTHD is a heavy duty single-monitor arm that you can use to mount monitors up to 813 mm (32 in.) in size and 9 kg (19.8 lb.) in weight. The height of the ARMPIVOTHD can easily be adjusted with one touch, and the finish on the ARMPIVOTHD makes it an attractive addition to your workspace.
Product dimensions 115 mm 80 mm 75 mm min 255 mm to max 315 mm 100 mm 210 mm 75 mm 100 mm Instruction manual min 10 mm to max 85 mm 100 mm min 170 mm to max 505 mm 115 mm 2
Technical specifications Type of measurement Measurement VESA mounting hole pattern 75x75 100x100 Weight capacity Up to 9 kg (19.8 lb.) kg Tilt +900 to -900 Screen size Maximum 813 mm (32 in.
Package contents 1 2 Spring arm VESA monitor mount Qty: One Qty: One 4 3 Grommet base plate Grommet knob Qty: One Qty: One 5 6 Grommet screw Grommet plate Qty: One Qty: One Instruction manual 4
8 7 Rubber pads Desk clamp Qty: Two Qty: One 9 10 L bracket Clamp screws Qty: One Qty: Five 12 11 Hex key holder 4 mm hex key Qty: One Qty: One Instruction manual 5
13 14 5 mm hex key 6 mm hex key Qty: One Qty: One 16 15 M4x12 mm thumbscrews M5x12 mm screws Qty: Four Qty: Four 17 Instruction manual 18 Washers Spacers Qty: Four Qty: Four 6
19 Instruction manual Qty: One Requirements • A monitor or display that’s compatible with a VESA mount • A Phillips screwdriver Requirements are subject to change. For the latest requirements, please visit www.StarTech.com/ARMPIVOTHD.
Assembly Attach the ARMPIVOTHD to your mounting surface You can use either the desk clamp or grommet mount to attach the ARMPIVOTHD to your mounting surface. Use the desk clamp to attach the ARMPIVOTHD Warning! Make sure that the weight of the monitor doesn’t exceed the weight capacity of this product. If you exceed the weight capacity, you might experience personal injury or damage to the product. This product can support the following weight: Up to 9 kg (19.8 lb.). 1.
4. Remove the backing from the two rubber pads (7) and affix the rubber pads to the tops of two of the clamp screws on the underside of the L bracket and spring arm. (figure 2) figure 2 Rubber pads Clamp screw L bracket Spring arm 5. Depending on the thickness of your mounting surface, do one of the following: • If your mounting surface is between 10 and 55 mm (0.4 and 2.2 in.) thick, position the desk clamp (8) so that the holes on the desk clamp line up with the top two holes in the L bracket.
figure 3 4 mm hex key 10 to 55 mm Clamp screw Desk clamp L bracket figure 4 50 to 85 mm 4 mm hex key Clamp screw Desk clamp L bracket Instruction manual 10
6. Snap the hex key holder (11) onto the L bracket. (figure 5) figure 5 Hex key holder L bracket 7. Turn the knob on the desk clamp counterclockwise until you reach the thickness of the mounting surface that you’re attaching the ARMPIVOTHD to. 8. Slide the desk clamp over the edge of the mounting surface. 9. Turn the knob clockwise to tighten the desk clamp.
Use the grommet mount to attach the ARMPIVOTHD Warning! Make sure that the weight of the monitor doesn’t exceed the weight capacity of this product. If you exceed the weight capacity, you might experience personal injury or damage to the product. This product can support the following weight: Up to 9 kg (19.8 lb.). 1. Insert the grommet screw (5) through the grommet base plate (3). (figure 7) figure 7 Grommet base plate Grommet screw 2.
5. Remove the backing from the two rubber pads (7) and affix the rubber pads to the tops of two of the clamp screws on the underside of the spring arm. (figure 9) figure 9 Grommet screw Rubber pad Spring arm 6. Place the assembled spring arm and grommet screw over the grommet hole in your mounting surface. 7. On the underside of the mounting surface, thread the grommet plate (6) through the grommet screw so that the grommet plate is flush against the mounting surface. 8.
Attach a monitor Warning! Attaching a monitor is a two-person job. Do not attempt to complete this task by yourself. To accommodate different monitor designs, the ARMPIVOTHD comes with two sets of screws that are different lengths and diameters, and a set of spacers. To select the appropriate screws for the type of monitor that you’re using, complete the following: • Determine whether the back of the monitor is flush or inset. • Determine the depth of the mounting holes on the monitor.
figure 11 Top of monitor VESA monitor mount M4x12 mm thumbscrew OR M5x12 mm screw Washer Spacer (if required) 5. Pull the tab on the spring arm (1), and slide the VESA monitor mount and monitor into the mount on the spring arm.
Adjust the spring arm You need to adjust the spring arm in two places. 1. To increase or decrease the tension in the spring arm (1), hold down the spring arm so that it is straight, and use the 6 mm hex key (14) to turn the screw in the joint of the spring arm counterclockwise or clockwise. (figure 13) figure 13 6 mm hex key 2. To change the angle that the monitor is tilted at, use the 6 mm hex key to turn the screw in the side of the mount counterclockwise.
Tip! If you used the desk mount to mount the ARMPIVOTHD, when you’re done adjusting the ARMPIVOTHD, you can store the hex keys in the hex key holder (11) on the side of the L bracket (9).
Route your cables 1. On the bottom portion of the spring arm (1), slide the cable cover up and away from the spring arm. (figure 16) figure 16 Spring arm Cable cover 2. On the upper portion of the spring arm, pull the ends of the cable cover away from the spring arm, and remove the cable cover from the spring arm.
3. Run the cables along the inside of the cable cover that you removed from the upper portion of the spring arm. 4. To reattach the cable cover, pull out the ends of the cable cover and insert the tabs on the inside of the cable cover into the holes on the spring arm.
5. Run the cables along the inside of the cable cover that you removed from the bottom portion of the spring arm. (figure 19) figure 19 Cable Spring arm Cable cover 6. Place the cable cover slightly higher than the cavity in the lower part of the spring arm, and slide the cable cover down so that the hooks on the cable cover slide into the clips in the spring arm.
Adjust the position of ARMPIVOTHD You can adjust ARMPIVOTHD in the following ways: 180° +90° 180° -90° 360° 270° Instruction manual 21
Technical support StarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and access our comprehensive selection of online tools, documentation, and downloads. For the latest drivers/software, please visit www.startech.com/downloads Warranty information This product is backed by a two-year warranty. StarTech.
Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise. StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you find the parts that connect your solutions. We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website.
