Desk-Mount Monitor Arm | Premium | Silver Actual product may vary from photos User Manual SKU#: ARMPIVOTB2 For the latest information and specifications visit www.startech.
Compliance Statements Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.
Warning Statements • Make sure that you assemble this product according to the instructions. • Do not exceed the weight capacity of this product. Overloading this product might result in injury or property damage. This product can support the following weight: 30.8 lb. (14 kg). • This product is intended for indoor use only and should not be used outdoors. Varningsmeddelanden • Se till att du monterar produkten i enlighet med instruktionerna. • Överskrid inte produktens viktkapacitet.
Mensagens de aviso • Certifique-se de que monta este produto de acordo com as instruções. • Não exceda a capacidade de peso deste produto. Sobrecarregar este produto pode resultar em ferimentos ou danos de propriedade. Este produto pode suportar o seguinte peso: 14 kg. • Este produto destina-se apenas a uma utilização no interior e não deve ser utilizado no exterior. Advertencias de uso • Asegúrese de ensamblar este producto según las instrucciones.
Safety Statements Safety Measures • Cables (including power and charging cables) should be placed and routed to avoid creating electric, tripping or safety hazards.
Table of Contents Compliance Statements.........................................................................1 Warning Statements...............................................................................2 Safety Statements...................................................................................4 Product Diagram.....................................................................................6 Product Dimensions.............................................................................
Product Diagram 1 2 5 4 3 1 Support Pole 4 Swivel Arm 2 Cable-Management Clip 5 Monitor Mount 3 C- Clamp To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Product Dimensions To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Product Rotation To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Product Information Specifications Type of measurement Measurement VESA mounting hole pattern 75x75 100x100 Tilt +900 to -150 Screen size Maximum 30 in. (762 mm) Rotate 3600 Swivel 3600 Weight/Load Capacity 30.8 lb. (14 kg) Lift 7.87 in. (200 mm) To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Package Contents Monitor Mount Swivel Arm Qty: One Qty: One Support Pole w/ C-Clamp Flange Mount Qty: One Qty: One To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
VESA Screws Torx Key Qty: Four Qty: One 3 mm Hex Key 4 mm Hex Key Qty: One Qty: One Access Card Monitor Mount Screws Qty: One Qty: Two To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Plastic Caps Qty: Four Installation Using the Grommet Mount 1. Turn the Desk Mount over so that the Support Pole faces downwards. Use the M3 Hex Keys to remove the four Hex Screws that are holding the base of the Support Pole to the C-Clamp. Removing the Four Hex Screws To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
2. Use a Phillips Screwdriver (not included) to remove the Screw from the Plate on the C-Clamp. 3. Remove the Plate, Two Washers, and the Knob from the bottom of the C-Clamp. Removing the Plate from the C-Clamp 4. Position the Support Pole over the Grommet Hole. 5. Slide the Plate (removed in step 3) through the Threaded Rod on the Knob. 6. Place the Knob through the Grommet Hole in the desk or table and into the Support Pole. 7. Turn the Knob clockwise to tighten it.
Using the C-Clamp By default, the Desk Mount comes with the C-Clamp preassembled. If you assembled the Grommet mount and want to switch back to a C-Clamp. Skip to step 5 if you do not have to reassemble the C-Clamp. 1. Insert the Knob through the hole in the C-Clamp. Attaching the Knob to the C-Clamp 2. Place a Washer onto the Knob. To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
3. Place a Phillips Screw through a Round Washer, Plate, and into the Washer on the Knob. Assembling the C-Clamp 4. Turn the Desk Mount over and use one of the M3 Hex Keys to insert four Hex Screws through the C-Clamp and into the base of the Mount. To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Attaching the Hex Screws to the C-Clamp 5. Using your hand, tighten the Knob until the C-Clamp is pressed tightly against the mounting surface. Securing the C-Clamp to the Mounting Surface To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Note: You can adjust the size of the C-Clamp by removing the two screws holding the upper and lower portions of the clamp together and re-installing the screws into the lower two screw holes. Adjusting the C-Clamp Mounting the Monitor Arm 1. Slide the Swivel Arm onto the Support Pole, so that the Swivel Arm resting on the Cable-Management Clip. To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Installing the Swivel Arm 2. Tighten the Swivel Arm using the Adjustment Screw located on the side of the Swivel Arm. Be careful not to over-tighten the Swivel Arm. The Swivel Arm should be secure but free enough to rotate. To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Attaching a Monitor Using the VESA Mount 1. Align the Mounting Holes (x 4) on the Monitor Mount with the mounting holes on the back of the Monitor. 2. Insert the Thumb Screws through the Monitor Mount and into the back of the Monitor. Mounting the Monitor Using the VESA Mount 3. Using your fingers, tighten the Thumb Screws. Warning! Do not over-tighten the screws. If you encounter resistance while you’re tightening the screws, stop tightening. Failure to do so could result in damage to the monitor.
Attaching an iMac Monitor 1. Turn off the iMac Monitor and disconnect all cables connected to the back of the iMac Monitor. 2. Turn the iMac Monitor around so that the back is facing forward. 3. Tilt the top of the iMac Monitor forward. 4. Insert the Access Card into the slot at the top of the Monitor Stand, disengaging the locking mechanism.
5. Tilt the iMac Monitor forward until the Monitor Stand is locked into place and the eight screws on the Monitor Stand are visible. 6. Lay the iMac Monitor face down on a flat surface (e.g. desk) with the Monitor Stand hanging over the edge of the desk. 7. Use the Torx Key to remove the eight screws from the back of the iMac Monitor. Removing the Screws from the iMac Monitor 8. Remove the stand from the iMac Monitor. 9.
10. Re-insert the eight screws through the Flange. 11. Using the Torx Key tighten the eight screws, being careful not to over-tighten. Installing the Flange 12. Slide the Plastic Caps (x 4) over the ends of the Monitor Mount, to protect the surface of the iMac Monitor. Installing the Plastic Caps To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
13. Align the 2 screw holes on the Monitor Mount with the 2 Mounting holes on the Flange. The orientation of the iMac Monitor is important. Aligning the Monitor Mount 14. Insert the 2 Monitor Mount Screws through the Monitor Mount and into the Flange. 15. Use the Hex Key (4 mm) to tighten the Monitor Mount Screws. Be careful not to over-tighten the Monitor Mount Screws. To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Attaching the Monitor Mount Attaching the Monitor Mount Notes: Attaching the Monitor Mount may require two people. The Monitor Mount supports up to a maximum of 30.86 lb. (14 kg). 1. While supporting the weight of the Monitor, carefully align the Mounting Hole on the Monitor Mount with the Mounting Peg on the top Swivel Arm. 2. Slide the Mounting Hole on the Monitor Mount over the Mounting Peg until it clicks into place.
Attaching the Monitor Mount 3. Using the 4 mm Hex Key, adjust the swivel tension of the Monitor Mount by loosening or tightening the Hex Screw located on the Monitor Mount next to the Mounting Hole. To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Removing the Monitor Mount 1. Slide the Thumb Clip towards the Arrow on the Monitor Mount, disengaging the locking mechanism. Sliding the Thumb Clip towards the Monitor Mount 2. While holding the Thumb Clip and the weight of the Monitor Mount, lift the Monitor Mount up sliding the Mounting Peg out of the Mounting Hole.
Routing the Cables The Desk Mount comes with a Cable-Management System that can be use to run the monitor cables down the mounting arms. Note: Make sure that the cables are unplugged before you route them through the Cable-Management System. 1. Thread the Cable through the hole in the Swivel Arm. 2. Run the Cable through the Cable-Management Clip on the side of the Support Pole. To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Warranty Information This product is backed by a ten-year warranty. For further information on product warranty terms and conditions, please refer to www.startech.com/warranty. Limitation of Liability In no event shall the liability of StarTech.com Ltd. and StarTech.
Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise. StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you find the parts that connect your solutions. We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website.
