Desk Mount Dual Monitor Arm | Articulating Actual product may vary from photos User Manual SKU#: ARMDUAL3 For the latest information and specifications visit www.startech.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which this manual applies by the third-party company in question.
Warning Statements • Make sure that you assemble this product according to the instructions. • Do not exceed the weight capacity of this product. Overloading this product might result in injury or property damage. This product can support the following weight: 35.2 lb. (2 x 8 kg). • This product is intended for indoor use only and should not be used outdoors. Varningsmeddelanden • Se till att du monterar produkten i enlighet med instruktionerna. • Överskrid inte produktens viktkapacitet.
Mensagens de aviso • Certifique-se de que monta este produto de acordo com as instruções. • Não exceda a capacidade de peso deste produto. Sobrecarregar este produto pode resultar em ferimentos ou danos de propriedade. Este produto pode suportar o seguinte peso: 2 x 8 kg. • Este produto destina-se apenas a uma utilização no interior e não deve ser utilizado no exterior. Advertencias de uso • Asegúrese de ensamblar este producto según las instrucciones.
Table of Contents Warning Statements...............................................................................2 Product Diagram.....................................................................................5 Product Dimensions.................................................................................................................................. 6 Product Information...............................................................................7 Package Contents.........................
Product Diagram 1 2 5 3 4 1 Swivel Arm Assembly 2 Monitor Mounts x 2 3 Pole 4 C-Clamp 5 Cable Management Clips x 5 (installed) To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Product Dimensions To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Product Information Package Contents Upper Desk Clamp Lower Desk Clamp Qty: One Qty: One Swivel Arm Assembly Pole Qty: One Qty: One To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Desk Clamp Screws Pole Assembly Screws Qty: Two Qty: Three 4 mm Hex Key 6 mm Hex Key Qty: One Qty: One To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
M4 x 12 mm Screws M5 x 12 mm Screws Qty: Eight Qty: Eight Washers Cable Management Clip Qty: Eight Qty: One To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Product Specifications 75 x 75 100 x 100 VESA LB kg 35.2 lb. (2 x 8 kg) Total Weight (two monitors) Max. 32 “ Screen Size 360o Rotation To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
- 300 to +300 Tilt - 900 to +900 Swivel Requirements • • • Phillips Head Screwdriver x 1 Monitors x 2 Mounting Surface x 1 To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Assembling the C-Clamp If the Mounting Surface’s thickness is between 40 mm - 85 mm: 1. Align the two lower Screw Holes on the Upper Desk Clamp with the two Screw Holes on the Lower Desk Clamp. 2. Insert the two Desk Clamp Screws through the Screw Holes on the Upper Desk Clamp and into the Screw Holes on the Lower Desk Clamp. 3. Using the 4 mm Hex Key tighten the two Desk Clamp Screws. Being careful not to over-tighten the Desk Clamp Screws.
If the Mounting Surface’s thickness is between 10 mm - 50 mm: 4. Align the two upper Screw Holes on the Upper Desk Clamp with the two Screw Holes on the Lower Desk Clamp. 5. Insert the two Desk Clamp Screws through the Screw Holes on the Upper Desk Clamp and into the Screw Holes on the Lower Desk Clamp. 6. Using the 4 mm Hex Key, tighten the two Desk Clamp Screws. Being careful not to over-tighten the Desk Clamp Screws.
Assembling the Monitor Arm 1. Align the three Screw Holes on the top of the C-Clamp with the three Screw Holes on the bottom of the Pole. 2. Insert the three Pole Assembly Screws through the Screw Holes on the top of the C-Clamp and into the Screw Holes on the bottom of the Pole. 3. Using the 4 mm Hex Key, tighten the three Pole Assembly Screws. Being careful not to over-tighten the Pole Assembly Screws.
4. Slide the Swivel Arm Assembly over-top of the Pole. Installing the Swivel Arm Assembly 5. Adjust the Swivel Arm Assembly up or down until it is at the desired height. 6. While holding the weight of the Swivel Arm Assembly, use the 6 mm Hex Key to tighten the Adjustment Screw on the Swivel Arm Assembly to secure the Swivel Arm Assembly in place. To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Tightening the Adjustment Screw 7. While supporting the weight of the Monitor Arm, slide the C-Clamp over the edge of the Mounting Surface. 8. Using your hand, tighten the Thumb Screw until the C-Clamp is pressed tightly against the Mounting Surface. Mounting the Monitors Note: It is recommend that two people are used to mount the Monitors to the Monitor Mounts. 1. Determine the size of screw to use to mount the Monitors to the Monitor Mounts (M4 x 12 mm or M5 x 12 mm).
2. While supporting the weight of the Monitor, align the Screw Holes on the back of the Monitor with the Screw Holes on the Monitor Mount. Aligning the Monitor with the Monitor Mount 3. Align a Washers (x 4), with a Screw Hole on the Monitor Mount. 4. Insert a Screw x 4 (M4 x 12 mm or M5 x 12 mm) through the Washer and Screw Hole on the Monitor Mount and into the Screw Holes on the back of the Monitor. 5.
Note: Do not over-tighten the Thumb Screws. If you encounter resistance while you’re tightening the Thumb Screws, stop tightening. Failure to do so could result in damage to the monitor. Attaching a Monitor to the Monitor Mount 6. Repeat steps 1 - 5 to mount the second Monitor. To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Adjusting the Monitors 1. Using the 6 mm Hex Key, loosen the Adjustment Screw that is located on the side of the Monitor Mount. Adjusting the Monitor Tilt 2. Adjust the tilt of the Monitor. 3. Once the Monitor is in the desired position, tighten the Adjustment Screw, securing the Monitor in place. To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Routing the Cables • • Monitor Cables can be routed along the Swivel Arm Assembly through the Cable Management Clips along the Swivel Arm Assembly and down along the Pole through the Cable Management Clip. Once the Monitor Arm is assembled the Hex Keys can be placed in the front of the Cable Management Clip on the Pole. Routing Cables To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.
Warranty Information This product is backed by a five-year warranty. For further information on product warranty terms and conditions, please refer to www.startech.com/warranty. Limitation of Liability In no event shall the liability of StarTech.com Ltd. and StarTech.
Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise. StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you find the parts that connect your solutions. We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website.
