Dual-Monitor Stand - Vertical ARMBARDUOV *actual product may vary from photos FR: Guide de l’utilisateur - fr.startech.com DE: Bedienungsanleitung - de.startech.com ES: Guía del usuario - es.startech.com NL: Gebruiksaanwijzing - nl.startech.com PT: Guia do usuário - pt.startech.com IT: Guida per l’uso - it.startech.com For the latest information, technical specifications, and support for this product, please visit www.StarTech.com/ARMBARDUOV.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols PHILLIPS® is a registered trademark of Phillips Screw Company in the United States or other countries. This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.
Warning statements Make sure to assemble this product according to the instructions. Failure to do so might result in personal injury or property damage. Make sure that the weight of the monitors doesn’t exceed the weight capacity of this product. If you exceed the weight capacity, you might experience personal injury or damage to the equipment. This product can support the following weight: (10 kg) 22 lb. per monitor mount. Never operate this product if parts are missing or damaged.
Table of Contents Warnings....................................................................................................................................................... i Introduction.............................................................................................1 Product diagram......................................................................................................................................... 1 Product dimensions...................................................
Introduction Product diagram VESA monitor mount Upper pole Cable-management clip Pole connector VESA monitor mount Cable-management clip Lower pole Baseplate Instruction manual 1
Product dimensions 48 mm 75 mm 100 mm 113 mm 35 mm 75 mm m 100 m m 116 m ±45° ±45° 818 mm 360° 316 Instruction manual mm m 434 m 2
Technical specifications Type of measurement Measurement VESA mounting hole pattern 75x75 100x100 Weight capacity Up to 10 kg (22 lb.) per monitor mount kg Tilt +450 to -450 Screen size Between 330 mm and 686 mm (13 in. and 27 in.
Package contents 1 2 Baseplate Lower pole Qty: One Qty: One 4 3 Upper pole Pole connector Qty: One Qty: One 5 6 VESA monitor mounts Cable-management clips Qty: Two Qty: Two Instruction manual 4
8 7 Cap 3 mm hex key Qty: One Qty: One 9 10 5 mm hex key 6 mm hex key Qty: One Qty: One 12 11 M4x12 mm screws M5x12 mm screws Qty: Eight Qty: Eight Instruction manual 5
13 14 Washers Instruction manual Qty: Eight Qty: One Requirements • Two monitors or displays that are compatible with one of the mounting hole patterns that ARMBARDUOV supports • A Phillips screwdriver Requirements are subject to change. For the latest requirements, please visit www.StarTech.com/ARMBARDUOV.
Assembly Warning! Make sure that the weight of the monitors does not exceed the weight capacity of this product. If you exceed the weight capacity, you might experience personal injury or damage to the product. This product can support the following weight: Up to 22 lb. (10 kg). Assemble the lower pole 1. Thread the cable-management clip onto the pole. 2. Thread the cap onto the pole. 3. Screw the pole into the baseplate. (figure 1) figure 1 Lower pole Cable-management clip Cap Baseplate 4.
Attach a VESA monitor mount 1. Slide one of the VESA monitor mounts down the lower pole. (figure 3) figure 3 VESA monitor mounts Lower pole 2. When the VESA monitor mount is at the desired height, use the 5 mm hex key to tighten the screw at the back of the VESA monitor mount.
Attach the upper pole 1. Screw the pole connector onto the lower pole. 2. Attach the other cable-management clip to the upper pole. 3. Screw the upper pole into the pole connector. (figure 5) figure 5 Upper pole Cable-management clip Pole connector Lower pole 4. Use the 3 mm hex key to tighten the two screws in the side of the pole connector.
Attach the second VESA monitor mount 1. Slide the other VESA monitor mount down the upper pole. (figure 7) figure 7 VESA monitor mount Upper pole 2. When the VESA monitor mount is at the desired height, use the 5 mm hex key to tighten the screw at the back of the VESA monitor mount.
Attach monitors to the VESA monitor mounts Warning! Attaching a monitor is a two-person job. Do not attempt to complete this task by yourself. Tipping hazard! The ARMBARDUOV is free-standing and when you attach monitors to it, you increase the tipping hazard. A second person is required to keep the ARMBARDUOV upright as you attach the monitors. ARMBARDUOV is designed to be used with monitors that are the same size and weight.
3. Carefully hook the screws into the top two slots on the VESA monitor mount on the upper pole. (figure 10) figure 10 Monitor M4x12 mm screw or M5x12 mm screw VESA monitor mount 4. Use a Phillips screwdriver to tighten the screws. (figure 11) Caution! If the VESA monitor mount starts to slip down the upper pole when you add the weight of the monitor, remove the monitor and use the 5 mm hex key to tighten the screw in the side of the VESA monitor mount.
5. Place two washers over the mounting holes in the VESA monitor mount. 6. Insert two M4x12 mm screws or M5x12 mm screws through the washers, the mounting holes in the VESA monitor mount, and into the back of the monitor. (figure 12) Warning! Do not over-tighten the screws. If you encounter resistance while you’re tightening the screws, stop tightening. Failure to do so could result in damage to the monitor. 7. Repeat steps 1 to 6 to attach a monitor to the VESA monitor mount attached to the lower pole.
Use the 75x75 VESA mounting hole pattern to attach a monitor To accommodate different monitor sizes, the ARMBARDUOV comes with two sets of screws that are different lengths and diameters. To select the appropriate screws for the type of monitor that you’re using, complete the following: • Determine the depth of the mounting holes on the monitor. • Determine the diameter of the mounting holes on the monitor. 1.
Adjust the tilt angle of your monitor 1. To change the angle that a monitor is tilted at, use the 6 mm hex key to turn the screw in the side of the VESA monitor mount counterclockwise. 2. When the screw is loose, position the monitor at the angle that works best for you. 3. Use the 6 mm hex key to turn the screw clockwise to tighten it. (figure 14) figure 14 +45° -45° 6 mm hex key 4.
Adjust the monitors +45° -45° 360° -45° +45° 360° Instruction manual 16
Technical support StarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and access our comprehensive selection of online tools, documentation, and downloads. For the latest drivers/software, please visit www.startech.com/downloads Warranty information This product is backed by a five-year warranty. StarTech.
Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise. StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you find the parts that connect your solutions. We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website.
