300Mbps Wireless-N Access Point/Repeater WFREPEAT300N *actual product may vary from photos DE: Bedienungsanleitung - de.startech.com FR: Guide de l'utilisateur - fr.startech.com ES: Guía del usuario - es.startech.com IT: Guida per l'uso - it.startech.com NL: Gebruiksaanwijzing - nl.startech.com PT: Guia do usuário - pt.startech.com For the most up-to-date information, please visit: www.startech.
FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Table of Contents Introduction.............................................................................................1 Packaging Contents.................................................................................................................................. 1 System Requirements............................................................................................................................... 1 Diagram...............................................................................
Introduction The WFREPEAT300N 300Mbps Wireless-N WiFi Access Point and Repeater has two selectable modes for extending the range of existing wireless networks or adding wireless capabilities to a non-wireless network. Using a wall plug design, this allows for convenient or hidden placement anywhere there is an available AC outlet. As a wireless repeater, the effective range of any 802.11n WiFi network can be increased, while still providing up to 300Mbps of data bandwidth.
Diagram Front Power Wireless Link/Activity Ethernet Link/Activity RJ45 Ethernet port Reset Button Back Modular Wall Plug Plug Release Button Instruction Manual 2
Installation Repeater Mode Setup: 1. Connect the Repeater to an available AC electrical outlet. 2. Wired Setup: Connect an RJ45 Ethernet cable from the Repeater to your computer. Wireless Setup: Connect to the wireless network ‘WiFi-Repeater’. 3. The default IP address on the Repeater is 192.168.10.1; configure your computer to a matching network address (192.168.10.x, where ‘x’ is between 2~255) with subnet set to 255.255.255.0 and gateway to 192.168.10.1. 4. Open a web browser window and enter 192.168.10.
. The next screen will display a list of detected wireless networks. Click the ‘Refresh List’ button to rescan. Select the desired wireless network and then click the ‘Next’ button. 8. Wireless encryption settings will be automatically detected and listed on the following screen. If the wireless network has a password, then enter this into the ‘Pre-Shared Key’ field. You should not need to change any other settings on this screen. Click ‘Apply and Reboot’ and you will receive a confirmation prompt.
9. After the unit has rebooted, the configuration settings/status will be listed. Confirm that the Mode has been set and the correct network name (SSID) is listed and connected to.
Access Point Mode Setup: 1. Connect the Repeater to an available AC electrical outlet. 2. Wired Setup: Connect an RJ45 Ethernet cable from the Repeater to your computer. Wireless Setup: Connect to the wireless network ‘WiFi-Repeater’. 3. The default IP address on the Repeater is 192.168.10.1; configure your computer to a matching network address (192.168.10.x, where ‘x’ is between 2~255) with subnet set to 255.255.255.0 and default gateway to 192.168.10.1. 4. Open a web browser window and enter 192.168.10.
7. The Repeater will automatically pre-configure itself with default information and then reboot. If there are multiple wireless networks or a problem occurs with the automatic setup, Advanced Configuration may be required. Otherwise the setup is complete. Note: Further instruction on Advanced Configuration settings for this device are available on the following pages, if desired. 8.
Advanced Configuration Advanced configuration options for the Repeater can be accessed via the web interface. 1. Connect an RJ45 Ethernet cable from the Repeater to your computer. 2. The default IP address on the Repeater is 192.168.10.1; configure your computer to a matching network address (192.168.10.x, where ‘x’ is between 2~255) with subnet set to 255.255.255.0 and default gateway to 192.168.10.1. 3. Open a web browser window and enter 192.168.10.1 into the address bar.
Wireless Click the link for ‘Wireless’ on the main menu, followed by ‘Basic Settings’. This will present the basic wireless configuration options for the current mode and also allow for manually changing the Mode type. Other options are available on the main menu, such as encryption settings (Security), list of detected WiFi networks (Site Survey), time of use scheduling (Schedule) and WiFi Protected Setup (WPS).
Wireless Cont’d Instruction Manual 10
LAN Interface The ‘LAN Interface’ options allow for configuration of settings for the LAN port (RJ45), when used in Access Point mode. The Unit’s IP address, DHCP settings and other related settings can be customized to match your needs. Management The ‘Management’ sections contain settings for various administrative functions for the unit. An important section to note is the ‘Password’ screen. It is recommended that the default password for the Unit be changed before you finish configuration.
Save/Reload Settings The current settings for the unit can be saved to a file on your computer and reloaded onto the Repeater at any time. The Repeater can be reset to factory defaults from this screen, by clicking the ‘Reset’ button. The Repeater can also be reset to factory defaults by pressing and holding the ‘Reset’ button, located next to the RJ45 port, for 10 seconds. Reboot This provides a remote method of soft restarting the Unit.
Specifications Supported Wireless Standards IEEE 802.11b/g/n Chipset ID Realtek RTL8196C Connectors 1 x RJ45 Ethernet female LEDs 1 x Power 1 x Wireless Link/Activity 1 x Ethernet Link/Activity Antenna Configuration 2x2:2 (TxR:S) Antenna Type 2dBi (internal) Wireless Frequency Range 2.4 GHz ~ 2.485 GHz Wireless Bandwidth 20/40MHz Wireless Encryption Supported WEP, WPA, WPA2 Maximum Wireless Distance 300m (950ft) Maximum Data Transfer Rate 802.11n: 300 Mbps 802.11g: 54 Mbps 802.
Technical Support StarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and access our comprehensive selection of online tools, documentation, and downloads. For the latest drivers/software, please visit www.startech.com/downloads Warranty Information This product is backed by a two year warranty. In addition, StarTech.
Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise. StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you find the parts that connect your solutions. We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website.
