USBthere 1 Port 165 ft. (50m) MultiSpeed USB 2.
USB221EXT Instruction Manual Thank you for purchasing the USB221EXT. Please read this guide thoroughly before installation. FCC Radio Frequency Interference Statement Warning The USB221EXT has been tested and found compliant with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when installed and operated in a commercial environment.
USB221EXT Instruction Manual Introduction……………………………………………………………… 1 Contents………………………………………………………………….. 1 About the USB221EXT………………………………………………….. 2 Before You Begin………………………………………………………... 6 Installation……………………………………………………………….. 6 Troubleshooting………………………………………………………….. 9 Specifications……………………………………………………………. 11 Technical Support………………………………………………………... 12 Warranty Information…………………………………………………….
USB221EXT Instruction Manual Introduction This manual is intended to assist IT professionals install the USB221EXT . The instructions in this guide assume a general knowledge of computer installation procedures, familiarity with cabling requirements, and some understanding of USB devices. NOTE: Notes give additional information that could make installation easier.
USB221EXT Instruction Manual About the USB221EXT The USB221EXT incorporates StarTech.com’s USBthere technology. This technology breaks the five-meter distance barrier for the connection of USB peripheral devices and allows users to enjoy the benefits of USB technology beyond the desktop. With the USB221EXT, USB devices can be located up to 165 feet (50 meters) from the host computer. The USB221EXT is composed of two individual units; the Local unit and the Remote unit.
USB221EXT Instruction Manual The Remote unit The Remote unit connects to the USB device using a conventional USB cable. Depending on your needs, it also connects to a power outlet through an AC power adapter. The Remote unit allows you to connect one USB device.
USB221EXT Instruction Manual 1 Link LED 5 Device LED(s) 2 Link Port (RJ45) 6 Device Port(s) (USB Type A) 3 Power LED 4 Power connector Network Cabling The Local unit and Remote unit are interconnected by up to 165 feet (50 meters) of Category 5 Unshielded Twisted Pair (UTP) cabling. The UTP cabling must have a straight-through conductor configuration, with no crossovers, and must be terminated with 8conductor RJ45 connectors at both ends.
USB221EXT Instruction Manual guarantee that all high-speed USB devices are compatible with the USB221EXT.
USB221EXT Instruction Manual Before You Begin Before you can install the USB221EXT, you need to prepare your site. 1. Determine where the host computer is to be located and set up the computer. 2. Determine where you want to locate the USB device(s). 3. If you are using surface cabling, ensure you have enough Category 5 UTP cabling to connect the two locations.
USB221EXT Instruction Manual the Local unit to the Remote unit. The UTP cabling must have a straight-through conductor configuration with no crossovers, and must be terminated with 8-conductor RJ45 connectors at both ends. With Surface Cabling 1. Plug one end of the Category 5 UTP cabling (not included) into the Link port on the Local unit. 2. Plug the other end of the Category 5 UTP cabling into the Link port on the Remote unit. With Premise Cabling 1.
USB221EXT Instruction Manual Connecting a USB Device 1. Install any software required to operate the USB device(s). Refer to the documentation for the device(s), as required. 2. Connect the USB device to the Device port on the Remote unit. 3. Check that the Device LED on the Remote unit is on.
USB221EXT Instruction Manual Troubleshooting The following table provides troubleshooting help. The topics are arranged in the order in which they should be executed in most situations. If you are unable to resolve the problem after following these instructions, please contact technical support for further assistance (see page 12). Symptoms/Cause All LEDs on Local unit and Remote unit are off. Cause: The USB221EXT is not receiving power from the adapter Remedy 1.
USB221EXT Instruction Manual Symptoms/Cause A device is connected to Remote unit and the corresponding Device LED is off Cause: a) The USB device is malfunctioning. b) The computer does not recognise the USB device. c) The application software for the device is not operating. Remedy 1. Disconnect the USB221EXT from the computer. 2. Connect the USB device directly to the USB port on the computer. 3. If the device does not operate properly, consult the user documentation for the device. 4.
USB221EXT Instruction Manual Specifications Range (over Category 5 UTP cable) 165 feet (50 meters) USB device support High-speed devices (480 Mb/s) Full speed devices (12 Mb/s) Low speed devices (1.5 Mb/s) USB hub support Any single chain can include four USB hubs and one USB221EXT, in any order. AC adapter(s) Input: 110/240 V AC, 50 – 60 Hz Output: 5 V DC, 2 A Power available to USB 1 x 500 mA device at Remote unit USB cable 2 meters (6.
USB221EXT Instruction Manual Technical Support StarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and access our comprehensive selection of online tools, documentation, and downloads. Warranty Information This product is backed by a one year warranty. In addition, StarTech.
