USB 3.0 to M.2 NGFF SSD Enclosure with UASP SM2NGFFMBU33 *actual product may vary from photos DE: Bedienungsanleitung - de.startech.com FR: Guide de l'utilisateur - fr.startech.com ES: Guía del usuario - es.startech.com IT: Guida per l'uso - it.startech.com NL: Gebruiksaanwijzing - nl.startech.com PT: Guia do usuário - pt.startech.com For the most up-to-date information, please visit: www.startech.
FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Table of Contents Product Diagram.....................................................................................1 Enclosure....................................................................................................................................................... 1 Internal Drive Tray...................................................................................................................................... 1 Introduction............................................................
Product Diagram Enclosure 1. Drive tray screws 2. USB 3.0 Micro-B port Internal Drive Tray 1. M.2 (NGFF) SSD Connector 2. Drive installation bracket 3.
Introduction Packaging Contents • 1 x USB 3.0 SATA HDD/SSD Enclosure • 1 x USB 3.0 Cable • 1 x SSD Mounting Screw and Standoff • 1 x Mini Screw Driver • 1 x Instruction Manual System Requirements System Requirements • Computer system with available USB 3.0 (5 Gbit/s) port or USB 2.0 port (480Mbps) • M.
Hardware Installation WARNING! SSD Drives and storage adapters require careful handling. If you are not careful with your SSD Drive, lost data may result. Always handle your drive with caution. Be sure that you are properly grounded by wearing an anti-static strap when handling computer components or discharge yourself of any static electricity build-up by touching a large grounded metal surface (such as the computer case) for several seconds. 1.
3. Install your M.2 SSD into the drive tray, by following the below steps. a. Determine if the drive installation bracket requires relocating by assessing your drive length. The board is labeled with the respective drive types for length but if your drive type is unknown, place your SSD next to the M.2 (NGFF) SSD connector, note which drive installation hole matches the height of your SSD. If the bracket is already installed in the correct position please proceed to step (d.). b.
c. (Only required if the drive installation bracket requires relocating) Reseat the drive installation standoff in the drive installation hole that matches your SSD. Replace the removed nut on the reverse side by using a small set of plyers or 5mm nut driver (not included). d. Using the included screw driver, remove the screw threaded into the drive mounting standoff. Note: The connector on your M.2 SSD is keyed so the drive will only fit one way.
e. Slide the M.2 connector on the SSD into the M.2 reciprocal connector on the drive tray. f. Press the drive down toward the drive mounting standoff, and drive the removed screw through the mounting hole on your SSD drive and into the drive mounting standoff using the included Philips head screw driver. Your M.2 SSD is now installed in the internal drive tray. 4. Slide the internal drive tray back into the enclosure so that the USB 3.
5. Using a Philips head screw driver (not included), replace the 2 drive tray screws on either side of the USB 3.0 Micro B port, on the front of the enclosure. 6. Using the included USB 3.0 cable, connect the SSD enclosure to your computer system. Your SSD enclosure is now ready to use.
How to Use Connecting the Hard Drive Once the enclosure has been attached to a computer, and the OS has installed the necessary software, the drive will be accessible as though it were installed within the system. Prior to using the drive, it will need to be formatted according to your operating system requirements. To format your newly attached hard drive, or create partitions, please see the Initializing the Hard Drive section.
Initializing the Hard Drive 1. If the SATA Hard Drive is blank it may need to be initialized and formatted before use. From the main Windows desktop, right-click on “My Computer” (“Computer” in Vista/ 7 / 8/ 8.1), then select Manage. In the new Computer Management window, select Disk Management from the left window panel. 2. A dialog window should automatically appear, asking you to initialize the drive.
Technical Support StarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and access our comprehensive selection of online tools, documentation, and downloads. For the latest drivers/software, please visit www.startech.com/downloads Warranty Information This product is backed by a two year warranty. In addition, StarTech.
Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise. StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you find the parts that connect your solutions. We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website.
