2.5in USB 2.0 FireWire SATA External Hard Drive Enclosure SAT2510U2F *actual product may vary from photos DE: Bedienungsanleitung - de.startech.com FR: Guide de l'utilisateur - fr.startech.com ES: Guía del usuario - es.startech.com IT: Guida per l'uso - it.startech.com NL: Gebruiksaanwijzing - nl.startech.com PT: Guia do usuário - pt.startech.com For the most up-to-date information, please visit: www.startech.
FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Table of Contents Introduction.............................................................................................1 Packaging Contents.................................................................................................................................. 1 System Requirements............................................................................................................................... 1 Installation..........................................................................
Introduction The SAT2510U2F External Hard Drive Enclosure supports both USB 2.0 and FireWire 400 (IEEE1394a) host connections in a slim, lightweight aluminum design. Packaging Contents • 1 x 2.
Installation WARNING! Hard drives require careful handling, especially when being transported. If you are not careful with your hard disk, lost data may result. Always handle your hard drive and storage device with caution. Hardware Installation 1. Remove the two small screws from either side of the rear panel of the enclosure and then pull the rear panel out. 2. Slide a 2.5” SATA hard drive into the 7+15 SATA connector on the inside of the rear panel. 3.
5. Connect the enclosure to the host computer system via FireWire or USB cable. If using the USB Y-cable, make sure to connect the primary connector on the cable to the host computer. The secondary connector is optional (extra power only). OPTIONAL: If the SATA drive/enclosure does not power up or is intermittent, additional power may need to be supplied. If using the USB Y-cable, connect the secondary connector on the cable to an available USB port on the host computer.
Locate the Disk that says it is “Unallocated” (check hard drive capacity to confirm it’s the correct hard drive) and then right-click in the section that says “Unallocated” and select “New Partition”. The New Partition Wizard will appear. Follow the instructions in the wizard to complete setting up the drive. Once complete, the Disk should show up as “Healthy” with a drive letter assigned (ie. E:). This drive letter should now appear within My Computer.
Specifications USB 2.0 Bus Interface FireWire400 (IEEE1394a) 1 x USB mini-B Connectors 1 x 6-pin FireWire 1 x DC power connector LEDs 1 x Power/Activity Chipset Initio INIC-1615 FW802C Compatible Hard Drives 2.5” SATA hard drive/solid state drive, up to 9.5mm height USB: 480Mb/s Maximum Data Transfer Rate FireWire: 400Mb/s Power Adapter (optional) 5VDC, 500mA or more, center positive, type H plug Dimensions 137.0mm x 80.0mm x 17.
Technical Support StarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and access our comprehensive selection of online tools, documentation, and downloads. For the latest drivers/software, please visit www.startech.com/downloads Warranty Information This product is backed by a two year warranty. In addition, StarTech.
Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise. StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you find the parts that connect your solutions. We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website.