USB 3.0/eSATA 8-Bay Removable 2.5/3.5” SATA Hard Drive Enclosure with UASP S355BU33ERM / S358BU33ERM *actual product may vary from photos DE: Bedienungsanleitung - de.startech.com FR: Guide de l'utilisateur - fr.startech.com ES: Guía del usuario - es.startech.com IT: Guida per l'uso - it.startech.com NL: Gebruiksaanwijzing - nl.startech.com PT: Guia do usuário - pt.startech.com For the most up-to-date information, please visit: www.startech.
FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Table of Contents Product Diagram.....................................................................................1 Front View..................................................................................................................................................... 1 Rear View - S358BU33ERM..............................................................................................................................................2 Rear View - S355BU33ERM........................................
Product Diagram Front View Drive Door Power Button Drive Activity LEDs / Drive Interface LEDs HDD Ready LED Instruction Manual 1 USB / eSATA LED
Rear View - S358BU33ERM USB 3.
Rear View - S355BU33ERM eSATA Host Interface Port USB 3.
Introduction Packaging Contents • 1x USB 3.0 / eSATA SSD/HDD Enclosure (S355BU33ERM / S358BU33ERM) • 1x SATA to eSATA full profile bracket • 1x eSATA cable • 1x USB 3.0 cable • 1x 2.5” drive Installation screw kit • 1x 3.
Hardware Installation WARNING! Hard drives and storage enclosures require careful handling, especially when being transported. If you are not careful with your hard disk, lost data may result. Always handle your hard drive and storage device with caution. Be sure that you are properly grounded by wearing an anti-static strap when handling computer components or discharge yourself of any static electricity build-up by touching a large grounded metal surface (such as the computer case) for several seconds. 1.
3. Slide the drive tray out of the slot, by gentley grasping the drive tray arm and pulling the tray out toward you. 4. Install your 2.5” or 3.5” hard drive, in the hard drive tray. Note: 2 types or drive screws are included. Larger screws for 3.5” drives, and smaller screws for 2.5” (Pictured below). Please ensure you are using the proper screw for your specific drive. Larger screw for 3.5” drives Instruction Manual Larger screw for 2.
a) If you are installing a 2.5” HDD/SSD i. Line up the bottom facing drive mount holes on your HDD/SSD, with the bottom drive holes on the drive tray.
ii. Using a Phillips head screw driver (not included), drive 4 of the 2.5” drive screws through the bottom drive holes on the drive tray into the mount holes on your HDD/SSD. b) If you are installing a 3.5” HDD i. Line up the side facing drive mount holes on your HDD, with the side drive holes on the drive tray. ii. Using a Phillips head screw driver (not included), drive 4 of the 3.
5. While holding the drive tray arm open, slide the drive tray back into the slot it was removed from. Once the drive tray has beein inserted, press the drive tray arm back into the latched position. Note: You will notices that as the driver tray arm is closed back into its original position that the tray may shift inwards a little. This is how the tray inserts the drive. 2 1 Note: Please repeat steps 2 through 5 for each additional drive. 6.
7. Connect the S355BU33ERM/S358BU33ERM to your computer system using the included USB 3.0 cable or the eSATA cable depending on your desired host connection. How to Use Connecting the Hard Drive Once the enclosure has been attached to a computer, and powered on, your computer system will automatically recognize the drive(s) and it will be accessible as though it were installed in the system internally.
Mac OS X To safely disconnect the attached drive from the host computer, close any windows listing the contents of the removable drive. Once all windows are closed, click on the USB storage icon on the desktop, and drag it to the Trash Can icon on the desktop. Allow 5 seconds before physically removing the enclosure/drive from the computer. Initializing the Hard Drive 1. If the drive array is new it may need to be initialized and formatted before use.
Technical Support StarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and access our comprehensive selection of online tools, documentation, and downloads. For the latest drivers/software, please visit www.startech.com/downloads Warranty Information This product is backed by a two year warranty. In addition, StarTech.
Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise. StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you find the parts that connect your solutions. We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website.
