Internal Drive Mounted Dual SATA Hard Drive RAID Adapter S322SAT3R *actual product may vary from photos DE: Bedienungsanleitung - de.startech.com FR: Guide de l'utilisateur - fr.startech.com ES: Guía del usuario - es.startech.com IT: Guida per l'uso - it.startech.com NL: Gebruiksaanwijzing - nl.startech.com PT: Guia do usuário - pt.startech.com For the most up-to-date information, please visit: www.startech.
FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Table of Contents Product Diagram.....................................................................................1 Front View..................................................................................................................................................... 1 Rear View....................................................................................................................................................... 1 Introduction......................................................
Product Diagram Front View Drive #1 SATA (DATA + Power) connector Rear View 2-pin LED connector for HDD Activity LED RAID setting jumper pins RAID unlock/ lock jumper pins 4-pin power connector Drive #2 SATA (DATA) connector SATA host interface connector Instruction Manual 1
Introduction Packaging Contents • 1x Internal Drive Mounted Dual SATA Hard Drive RAID Adapter (S322SAT3R) • 2x SATA Cable (50cm) • 1x 4-pin to SATA Power Adapter • 1x Installation Manual System Requirements • 2 x 2.5/3.
2. Connect the Drive #1 SATA (DATA + Power) connector on the S322SAT3R to the SATA (DATA+Power) connector on the first HDD/SSD mounted in your Computer System. 3. Using one of the included SATA Cables, connect the SATA (Data) connector on the second HDD/SSD to the Drive #2 SATA (DATA) connector on the S322SAT3R. 4. Connect an available SATA Power Source in your Computer System to the SATA (Power) connector on the second HDD/SSD.
5. Using the remaining included SATA Cable, connect the SATA Host Interface connector on the S322SAT3R to an available SATA Interface on your Computer System.
6. Using the included 4-pin to SATA Power Adapter, connect the 4-pin power connector on the S322SAT3R to an available SATA Power Source in your Computer System. 7. The S322SAT3R is now been installed, close your computer case and start your computer to build the RAID array. 8. (Optional) If you would prefer to lock your RAID array so it cannot be altered by the RAID mode setting jumper pins, power down and open your computer system, and set the RAID Lock/Unlock Jumper Pins to the lock position.
Configure RAID WARNING! Setting or changing your RAID modes may erase all data or metadata on your existing HDD/SSDs. RAID Lock/Unlock Jumper Pins The RAID lock/unlock jumper pins, located above the drive mounting brackets enable you to lock your RAID configuration so it cannot be changed. Or unlock your configuration so it can be changed. GND SET NC Use the included jumper and the table below, to short the pins and set the mode for your desired configuration.
Use the included jumpers and the table below, to short the pins and set your desired RAID mode. RAID Mode Description Short Pins RAID 0 Striping - Improves system performance 1-2, 4-5 RAID 1 Mirror – Creates a redundant drive on the second drive for security 2-3, 4-5 BIG Spanning – Creates a large single drive volume consisting of both drives.
LED Activity and Drive Failure Indicators The S322SAT3R includes a 2-pin LED connector for HDD Activity LED enabling you to visually monitor drive activity and RAID array health. Please review the table below for a list of each specific indication.
2. A dialog window should automatically appear, asking you to initialize the drive. Depending on the version of Windows, it will give you the option of either creating an “MBR” or “GPT” disk. GPT (GUID partition) is required for drives volumes larger than 2TB. However, it is not compatible with some older operating systems, while MBR is supported by newer and older operating systems. 3.
Technical Support StarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and access our comprehensive selection of online tools, documentation, and downloads. For the latest drivers/software, please visit www.startech.com/downloads Warranty Information This product is backed by a two year warranty. In addition, StarTech.
Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise. StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you find the parts that connect your solutions. We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website.
