300Mbps Wireless-N Guest WiFi Access Point / Account Generator 2T2R 2.4GHz R300WN22GAxx *actual product may vary from photos DE: Bedienungsanleitung - de.startech.com FR: Guide de l'utilisateur - fr.startech.com ES: Guía del usuario - es.startech.com IT: Guida per l'uso - it.startech.com NL: Gebruiksaanwijzing - nl.startech.com PT: Guia do usuário - pt.startech.com For the most up-to-date information, please visit: www.startech.
FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
IC Radiation Exposure Statement This equipment complies with IC RSS-102 radiation exposure limit set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 0.5cm between the radiator and your body. Déclaration d’exposition à la radiation Cet équipement respecte les limites d’exposition aux rayonnements IC définies pour un environnement non contrôlé. Cet équipement doit être installé et mis en marche à une distance minimale de 0.
Table of Contents Introduction.............................................................................................1 Packaging Contents.................................................................................................................................. 1 Product Diagram.....................................................................................1 Product Overview.....................................................................................................................
Configuration...........................................................................................47 Firmware Upgrade..................................................................................................................................... 48 Boot Code..................................................................................................................................................... 51 System Account............................................................................
Introduction Packaging Contents • 1 x Guest WiFi Access Point / Account Generator • 1 x Ethernet Cable • 2 x Screws for Wall Mounting • 1 x Power Adapter • 1 x Quick Start Guide • 1 x Instruction Manual CD Product Diagram Product Overview Guest Accont Generation Button WAN/ Uplink Port Reset Button LAN Ports LED Indicators Instruction Manual 1 DC Jack
LED PWR State Off Green Off SYS Green Green (Blinking) WAN LAN-1-4 No power Unit powered on Remains off while the unit is initializing Initialization complete, system is ready to use During firmware upgrades, this system LED will blink Off No network connection Green 10/100Mbps network connection established Green (Blinking) Indicates WAN activity Off No network connection Green 10/100Mbps network connection established Green (Blinking) Off WLAN Description Green Green (Blinking) Indicat
2. The distance between the two mounting sockets on the back of the Network Switch is approximately 106mm. Mark the distance on the wall, making sure your marks are straight and level. 3. Depending on the mounting surface, use the appropriate tools and hardware to install mounting screws into the surface. There should be a gap of approximately 2 mm between the head of the screw and the wall surface. 4. Place the Access Point so that the wide openings of the mounting sockets are over the screw heads.
10. The Setup Wizard will bring you through the basic configuration requirements in 3 sections: Internet – Allows you to select the appropriate Internet connection type for your ISP • DHCP Client – Allows the device to automatically obtain TCP/IP settings from your ISP Modem. • Static IP – Manually enter your desired IP address settings.
Wireless – Allows you to specify basic wireless network settings • Country – Choose between ETSI (European Telecommunications Standards Institute) or FCC (Federal Communications Commission – North America). • Channel – Select the channel ID for wireless connection. System – Allows you to specify basic system settings for the AP • Username / Password – Change the default username and password.
• System date and time – Specify the Time Zone and choose between manual date and time entry or NTP server settings. • Secure Administrate IP Address – Administrator can specify 5 IP addresses or a range to allow remote control access from network. 11. Click Finish to complete the Setup Wizard. 12. Click the Advanced Setup tab on the top menu to further modify device settings.
Item Default Description Syslog Disable Enables or disables the syslog server function. Server IP Address Empty Enter your syslog server LAN IP address. Server MAC Address Empty Enter your syslog server MAC address. Server 1 IP Address Empty Enter the WAN IP address of your first syslog server. Server 2 IP Address Empty Enter the WAN IP address of your second syslog server. Send to Email Disable Enables or disables the send to e-mail function.
Instruction Manual 8
Item Interval Time Description System System information would be sent according to specified interval time. Format: PRODUCT=GW-1;VER=2.00.00;LOGNAME=DVI; DATE=07Mar26;TIME=11:30:00; System Information 5~60 minutes WANMAC=09-00-0e-00-00-01;LANMAC=09-000e-00-00-02; WLANMAC=09-00-0e-00-00-03; IP_ADDRESS=210.66.37.
A log will be sent if system manager (Administrator) login to or logout from the device. Format: System Manager Activity Information When system manager login or logout PRODUCT=GW-1;VER=2.00.00;LOGNAME=SUN; DATE=07Mar26;TIME=15:23:32; WANMAC=09-00-0e-00-00-01;LANMAC=09-000e-00-00-02; WLANMAC=09-00-0e-00-00-03; IP_ADDRESS=210.66.37.21; SYS_NAME=Cafehotspot;LOCATION=East;CITY= Taipei; COUNTRY=Taiwan; FIRMWARE=v1.01.
User A log including users information will be sent when a user logs in Format: User Login When a user logs in PRODUCT=GW-1;VER=2.00.00;LOGNAME=ULI;D ATE=07Mar26; TIME=15:23:32;WANMAC=09-000e-00-00-01; LANMAC=09-00-0e-00-00-02; WLANMAC=0900-0e-00-00-03; IP_ADDRESS=210.66.37.21;USER_ NAME=asdfg12;USER_IP=10.59.1.1; USER_ MAC=02-34-3e-01-00;INTERFACE=Ethernet; USER_TYPE=Dynamic; User Type = Guest/ Employee A log including users information will be sent when user logged –out Format: PRODUCT=GW-1;VER=2.00.
A log including logged-in users information will be sent according to specified interval time Format: PRODUCT=GW-1;VER=2.00.00;LOGNAME=CUL ;DATE=07Mar26; TIME=15:23:32;WANMAC=0900-0e-00-00-01; Current User List .5~60 minutes. LANMAC=09-00-0e-00-00-02; WLANMAC=0900-0e-00-00-03; IP_ADDRESS=210.66.37.21;USER_ NUM=0;SEQ=1-5; USER_NAME=asdfg12,USER_ IP=10.59.1.
Item Default Description Session Trace Disable Disables or enables session trace function. Primary TFTP Server IP Address Empty Enter the IP address of the primary TFTP server. Secondary TFTP Server IP Address Empty Enter the IP address of the secondary TFTP server. Send Session Trace log file every 10 minutes Send the session trace log file at the specified interval. Acceptable range is from 5 to 1440 minutes Send to Email Disable Enables or disables the send to e-mail function.
E-mail (SMTP) Server needs to check my account Disable If your SMTP server requires authentication before accepting e-mail, enable this option. These values (username and password) are supplied by your network administrator, SMTP server provider or ISP. Username Empty Enter the username for the SMTP server (max 64 characters). Password Empty Enter the password for the SMTP server.
Item Default Description Bandwidth Disable Enables or disables Bandwidth Management. Maximum Upstream 64Kbps Specify the max upstream bandwidth (64 – 5120 Kbps). Maximum Downstream 128Kbps Specify the max downstream bandwidth (64 – 5120 Kbps). SNMP The SNMP configuration menu allows you to access to your device via Simple Network Management Protocol.
Item Default Description SNMP Disable Disables or enables SNMP management. SNMP Port 161 If SNMP is enabled, you can specify the SNMP port number. The allowed SNMP port numbers are 161 (default), or from 16100-16199 and Trap port numbers are 162 (default), or from 16200-16299. Trap Port 162 This Port setting is useful for remote control via NAT.
Security Pass Through The Pass Through function allows you to specify devices that can pass through the AP, without being checked and authorized. Click the Add to List button once you’ve created a new entry.
Item Default Description Pass Through Disable Enables or disables the pass through function. Destination URL/IP Address Pass Through URL or Website Empty Enter the URL Page (e.g. http://www.yahoo.com – Max 50 characters). Start / End IP Address Empty Enter the range of IP address you want to allow. Subscriber IP/MAC Address or LAN Device Pass Through Start / End IP Address Empty Enter the range of IP address you want to allow.
Item Default Description Filtering Disable Enables or disables the pass through function. HTTP Message to display when a website is blocked This Web Site is blocked by Administrator Enter the message you would like to display to the user when they attempt to access a restricted area. Start / End IP Address Empty Enter the range of IP addresses you want to allow. Please enter new restricted destination URL or Website Empty Enter the URL you would like to restrict.
Secure Remote The Secure Remote feature allows you to create a secure connection to a remote site or back-end system through a VPN PPTP Client. If “Secure Remote” is enabled, the RADIUS packet / syslog will be transferred to this secure connection. Default Description Auto-connect at Start-up (Always connect) Item Disable Click the check box to automatically establish the PPTP connection. PPTP Server IP address Empty Enter the PPTP server IP address provided by your ISP.
System System The System menu defines basic system settings.
Item Default Description System/Host Name Empty Enter a system name (Max 40 alphanumeric characters). Domain Name Empty Enter a domain name (Max 80 1 characters). Location Information Empty Enter your location and contact information if desired. GMT Select the appropriate time zone for your location.
Manual Setting Date (Year/Month/Day) - Manually set the date for the system (Ranges from 2011 to 2035). Time (Hour:Minute:Second) - Set the system time. NTP Setting Server IP / Domain Name 1 Empty Enter the primary IP address or domain name of NTP server (Max100 characters). Server IP / Domain Name 2 Empty Enter the secondary IP address or domain name of NTP server (Max100 characters). Update Time 24 Hours Enter the frequency (hours) in which to update the time.
Allow remote user to ping the device Enable This function allows remote users to ping the AP. Ping is normally used to test the physical connection between two devices, to ensure that everything is working correctly. SSL Certificate Default Options: Default or Customer Certificate WAN/LAN The WAN / LAN menu allows you to configure IP addressing and WAN connection settings.
Item Default Description Guest WLAN IP Address Setting IP Address 10.59.1.200 Enter the internal LAN IP address for the device. Subnet Mask 255.255.255.0 Enter the subnet mask for the IP address entered above. Employee WLAN IP Address Setting IP Address 10.59.2.200 The internal LAN IP address of your Wireless Subscriber Server Gateway. Subnet Mask 255.255.255.0 Enter the subnet mask for the IP address.
Server The Server menu allows you to configure Web and DHCP server settings. Item Default Description HTTP Port 80 Enter the HTTP port number (80 or from 8010 to 8060). For access to the AP under NAT, enter using the format: “http://[IP Address]:[Port Number]” HTTPS Port 443 Enter the HTTPS port number (443 or from 4430 to 4440).
Administrator Idle-Timeout 5 Minutes Enter an idle timeout duration in minutes (From 1-1440). If the idle time out is set as 5 minutes, it means that if the administrator doesn’t send packet in 5 minutes, the administrator will be logged out. DHCP Server DHCP Server DHCP Server DHCP Disable: Disable the DHCP server function. DHCP Server: Enable DHCP server function. Guest DHCP DHCP Pool Starting Address 10.59.1.2 Enter the Starting IP address for the Guest address pool.
Wireless The Wireless menu allows you to configure your desired wireless mode and applicable settings. Item Default Description General Settings Select the Country code: Country FCC -ESTI (Europe; Channel 1~13) -FCC (North America; Channel 1~11) Channel 6 Select the channel ID for wireless connection. Select one of the following modes: -802.11n+802.11g+802.11b -802.11n+802.11g 802.11 mode -802.11g+802.11n -802.11n only -802.11g only -802.
Channel Width Auto 20/40MHz Beacon Interval 200 Indicates the frequency interval of the beacon (From 1 to 1000). 2347 This valid range is from 256-2342. This setting determines the packet size at which the AP issues a Request To Send (RTS) before sending the packet. A low RTS Threshold setting can be useful in areas where many client devices are associating with the AP, or in areas where clients are far apart and can detect only the AP (not each other).
Guest Setting Guest ESSID Settings The Guest ESSID Settings menu allows you to configure your guest wireless settings and security. Item Default Description General Settings Active Activate or de-activate the Guest wireless connection interface. ESSID Guest The ESSID is the unique name that is shared among all points in a wireless network. It is case sensitive and must not exceed 32 characters. Security Enable Disable to allow users to communicate with the device without any data encryption.
The AP will randomly generate keys at the length specified here. (8-10 characters) Pre-shared Key Empty Use WPA with RADIUS Disable Server IP Empty Enter the RADIUS server IP address or domain name (Max 15 characters). Authentication Port 1812 Enter the authentication port number (From 0 to 65535). Shared Secret Key Empty Enter the RADIUS key Authentication The Authentication menu allows you to configure the type of guest user authentication required.
Item Default Description No Authentication: Subscriber can direct access the Internet without enter username and password. Built-in Authentication: Authentication Type Built-in Authentication The AP provides “Built-in Authentication” that allows you to build up an Internet service without extra authentication software. When selected, you can generate the subscriber account inside the AP, and the system will authenticate the subscriber login according to the generated account.
Usage Time The Usage Time menu allows you to manage account expiration and usage duration settings. Item Default Description Expiration 12 hours Enter the number of hours/days that unused accounts should be deleted after (Max 30 Hours / Days). Usage Time 3 hours Enter the number of hours/days the guest account should remain valid for (Max 30 Hours / Days). PIN Length 4 The field range is 4-6 characters.
Customization The Customization menu allows you to create a custom login page, add a logo, create an information pop-up window and user agreement as needed. Login Page Tab Provides several different options for you to create or redirect guest users to your login page.
Item Default Description Logo Disable Title Welcome Enter a page title for the top of the login box (Max 80 characters). Subtitle Guest Wifi Enter the subtitle name of subscriber login page (Max 80 characters). Footnote Diable Enter a footnote if desired e.g. “Please contact Customer Service, EXT 1000 for assistance” (Max 240 characters). Copywrite Enable Enter a copyright note for the bottom of the login page (Max 80 characters).
Redirect Item Default Description Redirect Disable Enter the URL where your login page is located (Max 200 characters), or click the button to create your own (sample code below).
Advanced Item Default Description Welcome Slogan Welcome Enter a Welcome slogan (Max 80 characters). Page Background None Enter your desired page background color in Hexadecimal. Article Empty Enter a paragraph for advisement or announcements (Max 1024 characters). Article Text Colour 000000 Enter your desired text color in Hexadecimal. Article Background Color None Enter your desired article background color in Hexadecimal.
• Sample Framed Page Logo Tab The Logo tab allows you to upload your company logo for use on the login page.
Information Window Tab The Information Window tab allows you to create a customized message to new guests after they log in. Item Default Description Display Information Window after a subscriber logs in successfully Enabled – Pop Up Window Name Information Window Enter the window name to be shown in the title bar (Max 30 characters). Main Message You can access the Internet now! Enter your main message / heading (Max 30 characters). Message Description This is an information...
• Sample Information Window User Agreement Tab The User Agreement tab allows you to create a customized user agreement page for guest users.
Item Default Description Title User Agreement Page Enter the window name to be shown in the title bar (Max 100 characters). Title Text Colour 000000 Enter your desired title text color in Hexadecimal. Article Empty The article is allowed the administrator to input a paragraph in the subscriber login page for advisement or announcement (Max 1024 characters). Article Text Colour 000000 Enter your desired text color in Hexadecimal.
Employee Setting Employee ESSID Settings The Employee ESSID Settings menu allows you to configure your employee wireless settings and security. Item Default Description General Settings Active Activate or de-activate the wireless connection interface. ESSID Employee The ESSID is the unique name that is shared among all points in a wireless network. It is case sensitive and must not exceed 32 characters.
Authentication Port 1812 Enter the authentication port number from 0 to 65535. Shared Secret Key Empty Enter the RADIUS key System Status Menu System Report The System report displays current basic system information, including: service connection status, host name, LAN, WAN, DHCP Configuration, DNS, SSL Certificate, network traffic Information and the system firmware version number.
Account List The Account List displays all account information on this device, including: the status, PIN, usage time, time created, login time, expiration time and status. This page will refresh automatically every 5 minutes, or you can click the Refresh button in the top right corner to update manually.
Account Log The Account Log displays account activity information. • Click the Export button to export the contents of the log to a text file (filename: export.
Current User Report The Current User report displays currently logged-in user status and allows the administrator to disconnect users if needed. This page will refresh automatically every 5 minutes, or you can click the Refresh button in the top right corner to update manually.
Session List The Session List displays the real-time session usage information for the AP. System Tools Menu The System Tools Menu allows you to upgrade Firmware, change passwords and backup or restore configuration files. Configuration The Configuration menu allows you to backup or restore the configuration settings for the device.
Item Backup Remote TFTP Server IP Address File Name Default - Description Click the button to save the system configuration to a file computer. (export.cfg) Empty Enter the IP address of the TFTP Server. Empty Enter your desired file name. Empty Click Choose File to select a file from your local PC Empty Enter the IP address of TFTP Server. Empty Enter the file name in the File Name field. - Click Apply and confirm to erase all configuration settings and revert back to factory default.
Item Default Description Local PC File Path - Click Choose File to select a file from your local PC Remote TFTP Server IP Address Empty Enter the IP address of TFTP Server. File Name Empty Enter the file name in the File Name field.
Scheduled Firmware Upgrade Tab The Scheduled Firmware Upgrade tab allows you to specify a file location and frequency for automated firmware upgrades. Item Default Description Disable/Enable Disable Disables or enables the scheduled firmware upgrade function. TFTP Server IP Empty Enter the IP address of the TFTP Server. File Synchronization Empty Enter the file name and location in the File Synchronization field.
Boot Code The Boot Code menu allows you to upload a new boot code file should an update become available. System Account The System Account menu allows you to change the administration account for the device. Item Description Username Enter a username up to 20, case-sensitive alphanumeric characters. Password Enter a password up to 20, case-sensitive alphanumeric characters. Confirm Re-enter the same password to confirm.
SSL Certificate The SSL Certificate menu allows you to add your certificate files to the device. PING The PING menu will issue the ping command to your specified IP address or URL. Item Description IP or URL Enter the IP address or the URL link.
Restart The Restart menu will reboot the device. Logout The Logout menu will exit from the configuration screen.
Specifications Supported Wireless Standards IEEE802.11b/g/n Chipset Ralink – RT3052 Connectors 5 x RJ45 Ethernet Female Antenna Configuration 2x2:2 (TxR:s) Wireless Frequency Range 2.400 – 2.484 Wireless Bandwidth 20/40MHz Wireless Encryption Supported WPA2(AES with IEEE 802.1x) WPA(TKIP with IEEE 802.
Technical Support StarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and access our comprehensive selection of online tools, documentation, and downloads. For the latest drivers/software, please visit www.startech.com/downloads Warranty Information This product is backed by a two year warranty. In addition, StarTech.
Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise. StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you find the parts that connect your solutions. We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website.
