IP2DVI Instruction Manual Ethernet to DVI Video Adapter Ethernet to DVI Video Adapter over IP
FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Table of Contents Introduction...................................................................... 1 Packaging Contents.....................................................................1 System Requirements..................................................................1 Installation........................................................................ 1 Hardware Installation....................................................................1 Driver Installation...................................
Introduction Packaging Contents • 1 x IP2DVI video adapter • 1 x Power Adapter • 1 x Driver and Software CD • 1 x Instruction Manual System Requirements • DVI enabled monitor/projector • TCP/IP network access • Microsoft Windows® XP/Vista (32-bit) Installation Hardware Installation LAN Port LAN Link Indicator Reset Button Power Indicator DVI Connector 1 Power Connector
LED Indicator LED Colour Power Red Link Green Description ON: receiving power from adapter OFF: no power supplied from adapter ON: network connection detected OFF: no network connection detected Flashing: data transfer Driver Installation Windows XP 1. Insert the provided CD into your disc drive. Locate and double-click the Setup.exe file in the Driver folder to launch the setup program. 2. During the installation, the screen may flicker a couple of times. This is normal.
3. When the ‘Install DisplayLink Software’ screen appears. Accept the terms in the license agreement to proceed. 4. If you have a firewall enabled on the computer, make sure to unblock the Cat5ShareStation utility. 5. Connect the IP2DVI unit to your router/switch and power it on. 6. When the Found New Hardware Wizard screen appears, select ‘Install the software automatically (Recommended)’ and click Next. 7. Click ‘Finish’ to complete the installation. 8.
10. Select ‘Generic DoIP’ and click the ‘Connect’ button. When the connection is ready, you will see the Generic DoIP icon become orange as below. 11. Then a pop-up message will appear in the notification area indicating the installation is complete. 12. If your monitor is not yet connected to the IP2DVI, make the connection and power on your monitor. 13. After the connection, the remote monitor should display an image from the computer.
Windows Vista 1. Insert the provided CD into your disc drive. Locate and double-click the Setup.exe file in the Driver folder to launch the setup program. 2. During the installation, the screen may flicker a couple of times. This is normal. When this section of the installation is complete, click ‘Finish’ to proceed. 3. When the ‘Install DisplayLink Software’ screen appears. Accept the terms in the license agreement to proceed.
4. After the installation completes, select Yes to restart your computer. 5. Connect the IP2DVI unit to your router/switch and power it on. 6. Launch the Cat5ShareStation utility from the icon on the Desktop. Click ‘unblock’ when you see the Windows Security Alert or other firewall warning. 7. Select ‘Generic DoIP’ and click the ‘Connect’ button. When the connection is ready, you will see the Generic DoIP icon become orange as below. 8.
Display Mode To change the display mode, right-click on the tray icon located in the System Tray, next to the clock.
Specifications 1 x RJ45 female External Connectors 1 x DVI-I 29-pin female 1 x Power (red) LEDs 1 x LAN Link (green) Maximum Resolution 1280 x 1024 Supported Colour Depth 16 and 32 bit Supported Display Modes • Extended Desktop (left/right/ above/below) • Mirrored (Cloned) Desktop AC: 100-240V, 50-60Hz Power Adapter DC: 5V, 2.5A Operating Temperature 10 - 40 degrees Storage Temperature -10 - 80 degrees Dimensions 97.0mm x 69.8mm x 20.
Technical Support StarTech.com’s lifetime technical support is an integral part of our commit-ment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and access our comprehensive selection of online tools, documentation, and downloads. Warranty Information This product is backed by a one year warranty. In addition, StarTech.
StarTech.com has been making “hard-to-find easy” since 1985, providing high quality solutions to a diverse IT and A/V customer base that spans many channels, including government, education and industrial facilities to name just a few. We offer an unmatched selection of computer parts, cables, A/V products, KVM and Server Management solutions, serving a worldwide market through our locations in the United States, Canada, the United Kingdom and Taiwan. Visit www.startech.
