3 Drive Trayless 3.5” SATA/SAS Mobile Rack HSB3SATSASBA *actual product may vary from photos DE: Bedienungsanleitung - de.startech.com FR: Guide de l'utilisateur - fr.startech.com ES: Guía del usuario - es.startech.com IT: Guida per l'uso - it.startech.com NL: Gebruiksaanwijzing - nl.startech.com PT: Guia do usuário - pt.startech.com For the most up-to-date information, please visit: www.startech.
FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Table of Contents Product Diagram.....................................................................................1 Front View..................................................................................................................................................... 1 Rear View....................................................................................................................................................... 1 Introduction......................................................
Product Diagram Front View 1. 3 x 2.5” Drive bays 2. 3 x 2.5” Drive bay key hole 3. 3 x /3.5in LED indicators Rear View 1. 2 x SATA Drive Power Connector ports 2. 3 x SATA Data Connector ports 3. Hard Drive LED Enable/Disable 4.
Introduction Packaging Contents • 1 x 3 SATA HDD Backplane • 3 x 18” SATA Cable • 2 x Bay Key • 1 x Installation Screw kit • 1 x Instruction Manual System Requirements • 1X Computer System with SATA connectivity and two available 5.25” bays • 2X Available SATA Power Connections • Up to three 3.5” SATA/SAS Hard Drive(s) WARNING! Hard drives and storage docks require careful handling, especially when being transported. If you are not careful with your hard disk, lost data may result.
Installation Hardware Installation 1. Ensure your computer system is powered down, and the power cable has been disconnected from the Power Supply. 2. Open your computer case (refer to the computer user manual for details), and place the 3.5in SATA/SAS HDD Backplane into two available 5.25” slots, lining up the side installation holes on the HSB2535SATBK (pictured below), with installation holes on the 5.25” slot inside the computer. 3.
3.5in Hard Drive Installation 1. Insert either of the included bay keys into the your desired 3.5in Drive bay key holes depending on which drawer you intend to install the drive into. And Turn the key clockwise into the unlock position. 2. Pull the drive door handle to open the drive bay 3. Insert your desired drive 4. Close the drive door.
3.5in Hard Drive Removal 1. Insert either of the included bay keys into the “2.5in/3.5in Drive bay key holes depending on which type of drive you intend to install. And Turn the key clockwise into the unlock position. 2. Pull the drive door handle to open the drive bay 3. Remove your drive 4. Close the drive door. Note: It is important to eject or unmount the hard drive from your computer system before physically removing the drive. See How to Use - Disconnecting the Hard Drive section for instructions.
How to Use Connecting the Hard Drive Once the drive has been installed in the drive bay, the drivers will install automatically, and the inserted drive will be accessible as though it were installed within the system. Note: some operating systems may require that the system be scanned for hardware changes from within device manager, for the newly connected drive(s) to be recognized. Prior to using the drive, it will need to be formatted according to your operating system requirements.
Initializing the Hard Drive 1. If the SATA Hard Drive is blank it may need to be initialized and formatted before use. From the main Windows desktop, right-click on “My Computer” (“Computer” in Vista/ 7 / 8), then select Manage. In the new Computer Management window, select Disk Management from the left window panel. 2. A dialog window should automatically appear, asking you to initialize the drive. Depending on the version of Windows, it will give you the option of either creating an “MBR” or “GPT” disk.
Technical Support StarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and access our comprehensive selection of online tools, documentation, and downloads. For the latest drivers/software, please visit www.startech.com/downloads Warranty Information This product is backed by a two year warranty. In addition, StarTech.
Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise. StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you find the parts that connect your solutions. We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website.
