Aluminum 5.25in Bay to 3.5in IDE HDD Mobile Rack DRW115ATABK *DRW115ATABK shown *actual product may vary from photos DE: Bedienungsanleitung - de.startech.com FR: Guide de l'utilisateur - fr.startech.com ES: Guía del usuario - es.startech.com IT: Guida per l'uso - it.startech.com NL: Gebruiksaanwijzing - nl.startech.com PT: Guia do usuário - pt.startech.com For the most up-to-date information, please visit: www.startech.
FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Table of Contents Introduction.............................................................................................1 Packaging Contents.................................................................................................................................. 1 System Requirements............................................................................................................................... 1 Installation..........................................................................
Introduction This high quality Removable ATA/ IDE Hard Drive Drawer/Mobile Rack delivers a professional-grade ATA/ IDE hot-swap solution, allowing you to quickly swap ATA/ IDE hard drives in and out of a computer without having to open the computer case. Simply install the (included) drive bay into a 5.25in drive bay on the host computer, then mount a 3.5in IDE HDD in the (removable) caddy.
Installation Installing Hard Drive in the Caddy WARNING! Hard drives and storage enclosures require careful handling, especially when being transported. If you are not careful with your hard disk, lost data may result. Always handle your hard drive and storage device with caution.
Installing the Bay in the PC WARNING! Computer parts can be severely damaged by static electricity. Be sure that you are properly grounded before opening your computer case. StarTech.com recommends that you wear an anti-static strap when installing any computer component. If an anti-static strap is unavailable, discharge yourself of any static electricity build-up by touching a large grounded metal surface (such as the computer case) for several seconds. 1.
Removing the Drive Drawer 1. Insert the key and turn clockwise to unlock the drive drawer. 2. Lift the handle and gently pull the caddy out of the bay. NOTE: Do not unlock the drawer when the hard drive is in use (See “Monitoring Your Hard Disk Drive and Drawer” below). Only power down the drive when the hard drive is idle. Once you have powered down the hard drive, wait about 15 seconds to let the hard drive “spin down” before removing the caddy from the bay.
To install the Swap Manager Software: 1. Insert your Swap Manager CD into your CD drive. 2. AutoPlay should automatically launch and display all of the folders on the CD. If not, open “My Computer” and double-click on the CD/DVD drive. 3. Enter the folder “AUTOptn”, and double-click the file “SwapManager.exe”. 4. Click Next to continue the installation. 5. Select Yes, I accept to agree to the terms in the license agreement and click Next. 6.
Troubleshooting Swap Manager If you have installed a new drive but there is no new icon listed in Swap Manager, first make sure that you have clicked the Swap In icon to let Swap Manager know that there is a new drive. If that does not work, check the following: • Make sure that the hardware is properly installed and that all cables are properly connected and firmly seated. • Make sure that the drive bay is connected to the secondary ATA/ IDE channel.
Specifications Number of Drive Bays 1 Host Interface ATA/ IDE (pass through) 1 x 40-pin IDE data male Host Connectors 1 x 4-pin LP4 Molex male 1 x Power LEDs 1 x Fan Failure Compatible Hard Drives 3.5in ATA/ IDE Fans 2 x 40mm (ball bearing) Insertion Rating 7, 000 cycles Enclosure Material Aluminum Dimensions (LxWxH) 220.0mm x 148.0mm x 41.
Technical Support StarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and access our comprehensive selection of online tools, documentation, and downloads. For the latest drivers/software, please visit www.startech.com/downloads Warranty Information This product is backed by a two year warranty. In addition, StarTech.
Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise. StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you find the parts that connect your solutions. We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website.