Outdoor 150Mbps Wireless N Access Point 1T1R 2.4GHz AP150WN1X1OD / AP150WN1X1OE / AP150WN1X1OG *actual product may vary from photos DE: Bedienungsanleitung - de.startech.com FR: Guide de l'utilisateur - fr.startech.com ES: Guía del usuario - es.startech.com IT: Guida per l'uso - it.startech.com NL: Gebruiksaanwijzing - nl.startech.com PT: Guia do usuário - pt.startech.com For the most up-to-date information, please visit: www.startech.
FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which this manual applies by the third-party company in question.
Table of Contents Product Diagram.....................................................................................1 Rear View....................................................................................................................................................... 1 Introduction.............................................................................................2 Packaging Contents.......................................................................................................
Product Diagram Rear View LED Panel Pole/Wall Mount Bracket Interface Cover Instruction Manual 1
Introduction Packaging Contents • 1 x Outdoor Access Point • 1 x PoE Injector • 1 x Metal Hose Clamp • 1 x Power Adapter • 1 x Quick Start Guide (CD) System Requirements • A networked computer system with a Java-enabled web browser (for configuration) • Cat 5 (or better) network cabling from PoE Injector to Wireless AP and PoE Injector to LAN Switch/router (no more than 100m total) • Mounting screws / anchors if wall mounting PoE Injector and/or Wireless AP Instruction Manual 2
Connection Ports External Antenna (optional) PoE Port LAN Port (Secondary) Interface Description External Antenna External RP-SMA Antenna connector (optional). Upgradable to high gain antennas for more range. See the External Antenna configuration section for setup procedures. PoE Port Power over Ethernet RJ-45 port used to connect the Access Point to the included PoE Injector for power and data connectivity.
LED Indicators Indicator PWR Wifi activity PoE LAN State Description ON The device is powered on Off The device is powered off Flashing Data is being transmitted / received over wireless Off No link detected ON Link detected Off No link detected Flashing Data is being transmitted / received on the PoE LAN interface ON Link detected Off No link detected Flashing Data is being transmitted / received on the Secondary LAN interface Installation Preparing Your Site 1.
Hardware Installation 1. Connect the included power adapter to an available wall outlet and the DC jack on the PoE injector. 2. Connect an Ethernet cable from the LAN port of the PoE Injector to your LAN switch or router. 3. Connect a second Ethernet cable from the PoE port of the PoE Injector, the other end of this cable will connect to the AP as instructed in the following steps. 4. Slide the bottom cover of the unit down to remove it and expose the ports. 5.
Operation Before operation, it is recommended that you ensure the Access Point is using the latest firmware version. Check www.startech.com/downloads for the latest firmware version. Default Settings SSID: AP150WN1X1OD Security: None Default IP Address: 192.168.1.200 ID: admin; PW: admin DHCP: Auto 1. Scan for available wireless networks on your PC and connect to the AP150WN1X1OD network 2. Open a web browser and enter the IP address 192.168.1.200 into the address bar, then press Enter. 3.
Network Name The default SSID of your Wireless Network is: AP150WN1X1OD To change it, enter your desired name in the SSID field. Users connecting wirelessly to the Access Point will use this ID to identify your wireless network. Click Next to continue Network Security By default, there is no Security Key configured on the Access Point. Enter your desired security key (WPA) in the Security Key field (recommended). Note: The key must be at least 8 characters long Click Next to apply your settings.
Advanced Configuration The following sections outline the advanced configuration settings available on the Access Point. These options can be accessed by clicking the More Settings link from the left side of the page, or by clicking the Finish button at the bottom of the Setup Summary page.
Wireless Settings Basic The Wireless Basic Settings page allows you to adjust the settings for your wireless network. These settings are for adjusting the Access Point after you have already gone through the Smart Setup Wizard and wish to further adjust your configurations. Disable Wireless LAN Interface: Turns off all wireless access. Band: Allows you to setup access under a specific combination of Wi-Fi speed standards.
Multiple AP: You may add one additional (SSID) to you Wireless network. The additional SSID can have its own security, band and data rate settings. You may restrict users for specific SSIDs or provide access only to some users with lower bandwidth by changing the band (i.e. only allow 802.11b access to specific users). Channel Width: Wi-Fi operates in two separate channel widths, 20Hz and 40Hz. 20Hz allows operation on channels 1-11, while 40Hz is 5-11. 40Hz allows for faster speeds.
Using the drop down menu, you can select which network you wish to configure and adjust the security settings for (standard wireless network or the multiple SSID network). Note: It is recommended to use WPA or WPA2 as your encryption type. WEP 64bit and 128bit security is a more primitive WiFi security encryption type which may limit wireless performance and speed from the Access Point. (Pre Service Pack 3 Windows XP computers may not support WPA2).
WDS Settings Wireless Distribution System (WDS) allows you to use the Access Point to wirelessly connect to other Access Points. In WDS mode, the Access Point can function as a Main Access Point which is connected to a network using a cable, or it can be a Relay Access Point which is wirelessly connected to the Main Access Point. To configure WDS mode you will need to adjust the settings for the following fields: a) Enable WDS: First you must enable the WDS function to use it.
f ) Channel: Ensure that all Access Points, Main or Relay, operate on the same wireless channel. g) DHCP: WDS mode requires that you have a static IP address for your Access Point. Enter a static IP address for your Access Point by selecting “Disable” under the DHCP field. h) IP Address: The IP address of the Access Point should be on the same subnet as the Main or Relay Access Points. For example, if the network you are connected to has an IP address range of 192.168.1.100 – 192.168.1.
Advanced Settings These settings allow you to control the advanced details of your wireless network configuration. Please use caution in changing these settings. Smart Features The Access Point provides Smart Features that offer convenience and protection for your wireless network. The Smart Features allow you to control access to your wireless network through on/off schedules, specific user authorizations, as well as through the range of your wireless coverage for your.
To do so: a) Click Enable Access Schedule b) Select which days you wish for your Wi-Fi to be available c) Select the time frame during that day that you wish for Wi-Fi to be available d) Apply Changes User Access Control User Access lets you deny / allow access to specific users connecting wirelessly to your network by MAC address. By inputting the MAC address(es) into this area, you can define whether that device is allowed into your network or not allowed.
IP Settings IP Address: The IP address of the Access Point. Subnet Mask: The subnet of the Access Point. Default Gateway: The Access Point to another network, normally the IP address of your router. DHCP: The Access Point includes a ‘Smart’ AUTO DHCP feature to help manage the IP addresses within your wireless network and with your router.
Management Settings The Management features on the Access Point allow you to view the status of your Access Point and your wireless network. System Status The Access Point System Status page provides full information regarding the system, wireless network and configurations as well as the current IP settings of the Access Point. This page is often used to check the health of your wireless network and the link to your home router/network.
Save and Reload Settings Allows you to back-up your current settings which may be reloaded at a later time. This feature may be useful for testing new features and settings without having to worry about returning to a stable platform. You may also reset the Access Point’s settings to factory settings by pressing Reset. By resetting the Access Point you will lose all previous configurations and will need to run the Smart Setup Wizard again to reconnect to a Home Network.
Specifications Supported Wireless Standards IEEE802.11 b/g/n Chipset Realtek - 8196C 2 x RJ45 Ethernet Female Connectors 1 x RP-SMA (Coax; Reverse Polarity SubMiniature A) Female Antenna Configuration 1x1:1 (TxR:s) Antenna Type 12dBi Directional Antenna Wireless Frequency Range 2.400 ~ 2.484GHz Wireless Bandwidth 20/40MHz 64/128 bit WEP WPA(TKIP with IEEE 802.1x) Wireless Encryption Supported WPA2(AES with IEEE 802.1x) WPA Mixed 802.
Technical Support StarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and access our comprehensive selection of online tools, documentation, and downloads. For the latest drivers/software, please visit www.startech.com/downloads Warranty Information This product is backed by a two year warranty. In addition, StarTech.
Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise. StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you find the parts that connect your solutions. We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website.
