PCI31PUSB/LP & PEX312PUSB/LP PCI/PCIe 12V Powered USB Card PUSBADAP/LP 12V/24V Daughter Card
FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Instruction Manual Table of Contents Introduction ................................................................................... 1 Features.......................................................................................1 Package Contents........................................................................1 Hardware Guide.............................................................................. 2 PCI312PUSB/LP, PEX312PUSB/LP.............................................2 Jumper Settings...
Instruction Manual Introduction Thank you for purchasing a StarTech.com Powered USB 2.0 Adapter Card (available in both PCI and PCI Express formats as well as Standard and Low Profile). Now, adding Powered USB capability to a computer has never been easier! Fully compatible with USB1.1 OHCI and USB2.0 ECHI specifications, the cards support data speeds of up to 480 Mbps and provide power to Powered USB devices through industrial standard Powered USB connectors.
Instruction Manual Hardware Guide PCI312PUSB/LP, PEX312PUSB/LP J4: USB Ports 4, 5 (for Expansion) +5 DD+ G +5 DD+ G JP2: +12V Selector J5: AUX Power J1~J3: External JP1: Powered USB Ports (x3) +5V Selector Jumper Settings JP1 (+5V Selector) Default: The USB2.0 Bus Power is supplied by the motherboard PCI slot (DC+5V supplied from PCB) The USB2.0 Bus Power is supplied by the AUX power connector (J5).
Instruction Manual Jumper Settings - Cont’d JP2 (+12V Selector) Settings Default: The 12V power source of the Powered USB connectors are supplied by the PCI slot into which the card is installed The 12V power source of the Powered USB connectors are supplied by the AUX power connector (J5). This will require that a power cable be connected from the computer power supply to J5. This option provides more power for the Powered USB devices over the USB2.0 cable.
Instruction Manual Jumper Settings JP2 (24V Selector) Settings Default: The power source of the 24V-keyed PoweredUSB connector is supplied from the internal step-up switching regulator (jumpers must be set identically, both at INT or EXT. The power source of the 24V-keyed Powered USB connector is supplied from the external Power DIN input connector, in this case, a 24V AC adapter will be required. Please see http://www.startech.com for more information.
Instruction Manual 5. Remove a metal bracket that is adjacent to or near the one removed in step #2, and fasten PUSBADAP/PUSBADAPLP directly to the metal rear panel of the computer case. 6. Connect the remaining end of the 9-Pin USB Header Cable used in step #3, to the USB IN connector, denoted as J1: USB Input Connector (from Host USB port) (see diagram, pg.3) on the PUSBADAP board. 7. PCI312PUSB/PEX312PUSB: By default, JP2 (see pg. 3) is set to PCI.
Instruction Manual 2. Locate an empty PCI/PCI Express slot and remove the metal bracket covering the accompanying empty port/socket. 3. Position the card above the open PCI/PCI Express slot, ensuring that the card is properly aligned with the slot. Insert the card firmly into the slot, distributing force evenly across the length of the board, then fasten the metal bracket to the computer case (using the screw removed in step #2, if necessary). 4. By default, JP2 (see pg.
Instruction Manual #2), to the USB Header connector on the host motherboard. For further instructions on how to locate the appropriate connection on the motherboard, please consult the documentation that was included with your motherboard/computer at the time of purchase. Software Installation PCI312PUSB/LP and PEX312PUSB/LP are natively supported by Windows® XP (SP2) 2000 (SP4) and Vista™.
Instruction Manual 8
Instruction Manual Specifications PCI312PUSB PEX312PUSB 3 x 12V Powered USB male connectors Connectors 1 x LP4 Connector 1 x Internal USB (9 pin) Header Connector for expansion 1x Jumper Connector OS Support Dimensions (L x W) 1x 12v Power USB Connector 1x 24v Power USB Connector 1x 4 pin Power Din Connector 1x Internal USB Connector 1x Jumper Connector 1x LP4 Connector Windows® 2000/ME/2003/XP/Vista™ 81.2 mm x 66.7 mm (3.2 in ) x (2.63 in ) Regulatory Certified 120 mm x 66.7 mm (4.72 in ) x (2.
Instruction Manual Technical Support StarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and access our comprehensive selection of online tools, documentation, and downloads. Warranty Information This product is backed by a lifetime warranty. In addition, StarTech.
StarTech.com has been making “hard-to-find easy” since 1985, providing high quality solutions to a diverse IT and A/V customer base that spans many channels, including government, education and industrial facilities to name just a few. We offer an unmatched selection of computer parts, cables, A/V products, KVM and Server Management solutions, serving a worldwide market through our locations in the United States, Canada, the United Kingdom and Taiwan. Visit www.startech.
