0/100Mbps VDSL2 Ethernet Extender Kit over Single Pair Wire - 1.5km 110VDSLEXT2 / 110VDSLEX2GB / 110VDSLEX2EU *actual product may vary from photos DE: Bedienungsanleitung - de.startech.com FR: Guide de l'utilisateur - fr.startech.com ES: Guía del usuario - es.startech.com IT: Guida per l'uso - it.startech.com NL: Gebruiksaanwijzing - nl.startech.com PT: Guia do usuário - pt.startech.com For the most up-to-date information, please visit: www.startech.
FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Table of Contents Introduction.............................................................................................1 Packaging Contents.................................................................................................................................. 1 System Requirements............................................................................................................................... 1 Product Overview......................................................................
Introduction Packaging Contents • 1x Ethernet VDSL2 - Transmitter • 1x Ethernet VDSL2 - Receiver • 2x RJ45 Cables • 8x Rubber Feet • 2x Power Adapters • 1x Instruction Manual • 2x Wall mount screws and anchors System Requirements • 10/100 Mbps Ethernet Network • Available AC electrical outlets • RJ11 cable or RJ11 lines in building infrastructure Instruction Manual 1
Product Overview The Ethernet Extender Kit consists of x2 Ethernet VDSL2 Transmitter/Receiver units. Either unit can be used at either end of your configuration (transmitting end or receiving end), however the DIP switch settings should be modified according to your specific needs based on direction of traffic. By default, all DIP Switch settings on each of the two units are set to the downward (OFF) position. See the DIP Switch and Mode Settings section for more information.
LED Indicators LED (Green) OFF ON (Solid) FLASHING PWR (Power) Power Off Power On NA ETH (Ethernet) No RJ45 Link/Connection Connected Activity DSL (VDSL) No VDSL Link/Connection Connected Slow - Establishing Connection Fast – Sync / Activity Instruction Manual 3
Installation Hardware Installation One of the Ethernet Extender Kits units should be considered a “Transmitting Unit”, while the other should be considered a “Receiver Unit.” Transmitter Unit 1. Place one of the units at the local location, this unit will act as the Transmitter Unit. 2. Connect the provided power adapter from an AC electrical outlet to the DC Power Input on the Transmitter Unit. The “PWR” LED should light up solid. 3. Set all four of the DIP switches to the downward (OFF) position.
DIP Switch and Mode Settings The Ethernet Extender Kit units have a 4-position DIP switch for configuration of CO/ CPE, Profile, Band, and SNR. By default, all DIP switch settings for both units are set to the downward “OFF” position.
position at the transmitting end. Profile Mode Profile Mode is the VDSL2 profile, 17a or 30a, with 30a allowing higher bandwidth at longer distances. Set this DIP switch to the upward (ON) position for 17a, or the downward (OFF) position for 30a, depending on your network requirements and preferences. Band Mode Band Mode places the unit in either Symmetric or Asymmetric mode.
Technical Support StarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and access our comprehensive selection of online tools, documentation, and downloads. For the latest drivers/software, please visit www.startech.com/downloads Warranty Information This product is backed by a two year warranty. In addition, StarTech.
Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise. StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you find the parts that connect your solutions. We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website.
